Hi community.
I'm trying to build up a tcp failover cluster. I'm trying to save and restore active tcp sessions (that belong to master side) on the salve side, when master experience the failover. So that, I would have needed tcp sockets opened on slave side (that were indeed started on the master side).
The main goal is to make it working for kamailio (SER) daemon. I'm trying to reach real-time HA cluster for calls that are being on the line and save them when master experience the failure.
What I've already done: 1. Created well-formed rule set for iptables: -A INPUT -i eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -i eth0 -d 10.100.100.27/32 -j DROP -A INPUT -m state --state INVALID -j LOG
-P FORWARD DROP -A FORWARD -i eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -i eth0 -d 10.100.100.27/32 -j DROP -A FORWARD -m state --state INVALID -j LOG
where 10.100.100.27 - VIP address The same rule set is stored on the slave side.
2. Configured conntracd: Sync { Mode FTFW { DisableExternalCache Off CommitTimeout 1800 PurgeTimeout 5 }
UDP { IPv4_address 10.100.100.28 IPv4_Destination_Address 10.100.100.29 Port 3780 Interface eth0 SndSocketBuffer 1249280 RcvSocketBuffer 1249280 Checksum on }
Options { ExpectationSync { sip ftp } } }
General { Nice -20 HashSize 32768 HashLimit 131072 LogFile on Syslog on LockFile /var/lock/conntrack.lock UNIX { Path /var/run/conntrackd.ctl Backlog 20 } NetlinkBufferSize 2097152 NetlinkBufferSizeMaxGrowth 8388608 Filter From Userspace { Protocol Accept { TCP UDP ICMP } Address Ignore { } } }
where 10.100.100.28 - master and 10.100.100.29 - salve. The same config file is stored on the slave side, but addresses in UDP section are swapped. I tried to use Address Ignore block, where I made an effort to add ip addresses belong to the node, but with this one it didn't work at all - there was no exchange of conntrackd traffic between cluster nodes. So I leaved it empty.
3. Configured keepalived:
vrrp_instance E1 { interface eth0 state BACKUP virtual_router_id 61 advert_int 1 authentication { auth_type PASS auth_pass herepassword } virtual_ipaddress { 10.100.100.27/27 dev eth0 } nopreempt garp_master_delay 1
notify_master «/etc/conntrackd/primary-backup.sh primary» notify_backup «/etc/conntrackd/primary-backup.sh backup» notify_fault «/etc/conntrackd/primary-backup.sh fault» }
where primary-backup.sh is a script, that is provided with conntrackd libraries. You will ask me, why I don't use dedicated link for conntrackd? I used it for a while, but as matter of fact it didn't change anything, so I simplified the assignment for myself and made it deprecated.
How the process of failover looks like for the current moment:
1. I use telnet/ssh/ftp to connect to VIP address located (for current moment) on master side; 1.1. Master side experience a fail - I bring down the eth0 link; 2. Backup node see the problem and execute: /etc/conntrackd/primary-backup.sh primary so the following sequence of conntrackd command are executed: /usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -c /usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -f /usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -R /usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -B
3. I can see the needed telnet/ssh/ftp session on the backup node by command: conntrackd -i It has state - ESTABLISHED state (I'm confident that this is session I need, cuz I remember the client's port was used for connection on master node).
4. But when I try to send packets (commands) from my client, server resets the TCP session with [R] flag. Tcpdump output on the backups node shows only 2 rows:
11:12:26.621001 IP telnet.client.test.56238 > 10.100.100.27.telnet: Flags [P.], seq 1380562259:1380562261, ack 1731331297, win 237, options [nop,nop,TS val 43239685 ecr 81905017], length 2 11:12:26.621083 IP 10.100.100.27.telnet > telnet.client.test.56238: Flags [R], seq 1731331297, win 0, length 0
As you can see, firewall accepts the traffic (in INPUT and FORWARD chains),this means that session exists on the backup internal cache/kernel table (otherwise iptables would drop the packet), but it then resets it, why? I tried to test it with ssh, telnet and ftp. No success at all. I also tried to remove flushing command, so that sequence was changed to : /usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -c /usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -R
and it also didn't work.
So if someone has the needed experience, please don't be apathetic, help a bit. At least I need a hint where to look for a problem.
-- BR, Donat Zenichev
Тема: TCP failover doesn't work as expected (Прочитано 605 раз)
