Не могу настроить кулеры

[NikWeo]

Добрый день форумчанам,суть вопроса: как увеличить скорость кулеров (1 на процессоре, 1 видеокарта, 2 выдув из системника и 1 на вдув) точнее показывает скорость 0
Ниже приведу выводы команд

sensors

(Нажмите, чтобы показать/скрыть)

nikita@terminal ~ $ sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0:       +54.0°C  (high = +80.0°C, crit = +100.0°C)
Core 1:       +56.0°C  (high = +80.0°C, crit = +100.0°C)

w83627dhg-isa-0290
Adapter: ISA adapter
Vcore:        +1.23 V  (min =  +0.00 V, max =  +1.74 V)
in1:          +0.74 V  (min =  +1.55 V, max =  +0.39 V)  ALARM
AVCC:         +3.41 V  (min =  +2.98 V, max =  +3.63 V)
+3.3V:        +3.41 V  (min =  +2.98 V, max =  +3.63 V)
in4:          +1.30 V  (min =  +1.34 V, max =  +2.00 V)  ALARM
in5:          +0.57 V  (min =  +0.30 V, max =  +1.11 V)
in6:          +0.00 V  (min =  +1.22 V, max =  +1.94 V)  ALARM
3VSB:         +3.38 V  (min =  +2.98 V, max =  +3.63 V)
Vbat:         +3.33 V  (min =  +2.70 V, max =  +3.63 V)
fan1:           0 RPM  (min = 1318 RPM, div = 128)  ALARM
fan2:           0 RPM  (min = 10546 RPM, div = 128)  ALARM
fan3:           0 RPM  (min = 1054 RPM, div = 128)  ALARM
fan4:           0 RPM  (min = 10546 RPM, div = 128)  ALARM
fan5:           0 RPM  (min = 10546 RPM, div = 128)  ALARM
temp1:        +40.0°C  (high = -42.0°C, hyst = +32.0°C)  ALARM  sensor = CPU diode
temp2:       -128.0°C  (high = +80.0°C, hyst = +75.0°C)  sensor = CPU diode
temp3:       +127.0°C  (high = +80.0°C, hyst = +75.0°C)  ALARM  sensor = thermistor
cpu0_vid:    +0.000 V
intrusion0:  ALARM

pwmconfig

(Нажмите, чтобы показать/скрыть)

nikita@terminal ~ $ sudo pwmconfig
[sudo] password for nikita:
# pwmconfig revision 6166 (2013-05-01)
This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.

We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.

Found the following devices:
   hwmon0/device is coretemp
   hwmon1/device is w83627dhg

Found the following PWM controls:
   hwmon1/device/pwm1           current value: 255
   hwmon1/device/pwm2           current value: 127
   hwmon1/device/pwm3           current value: 255
   hwmon1/device/pwm4           current value: 127

Giving the fans some time to reach full speed...
Found the following fan sensors:
   hwmon1/device/fan1_input     current speed: 0 ... skipping!
   hwmon1/device/fan2_input     current speed: 0 ... skipping!
   hwmon1/device/fan3_input     current speed: 0 ... skipping!
   hwmon1/device/fan4_input     current speed: 0 ... skipping!
   hwmon1/device/fan5_input     current speed: 0 ... skipping!

There are no working fan sensors, all readings are 0.
Make sure you have a 3-wire fan connected.
You may also need to increase the fan divisors.
See doc/fan-divisors for more information.

Пытался редактировать
sudo echo "255" > /sys/class/hwmon/hwmon/device/fan1_input
Пишет отказано в доступе хотя и через sudo

В общем как можно увеличить скорость кулеров в моей ситуации? помогите пожалуйста
ОС: Linux Mint 17.1 (знаю можете сказать иди на форум мятной, но она сделана на той же убунте)
Материнская плата: intel dg43gt


P.S. может ли быть дело в минте (как вариант могу установить Ubuntu)

[maks05]

Начнём с того, что есть ли проблема вообще? В чём она? Вы физически наблюдаете перегрев? Или беспокоит шум вентиляторов?

Второе. Какое железо, какой корпус системника (марка, модель)?

Третье. Как и куда подключены вентиляторы? В идеале они должны подключаться на материнку и, желательно, чере 4-контактные разъёмы. Тогда контролем температуры и скоростью вентиляторов будет управлять BIOS компьютера, в котором, соотвественно, и нужно производить все настройки. Ну или подключать на внешний реобас с ручным управлением.

[NikWeo]

Проблема в том что показатели в sensors равны 0 (как в такой ситуации мониторить температуры?)
Корпус Gigabyte 3D Aurora
Подключены к матери но через 3 пина а не 4

P.S. уже подумываю что реобас всё таки лучше в данной ситуации, но как тогда быть с 0 показателями (каждый раз смотреть через биос нет возможности)
Какие данные по железу нужны объясните пожалуйста

[v!tax]

Код: [Выделить]

sudo sensors-detect?

[NikWeo]

Вот вывод команды sensors-detect

(Нажмите, чтобы показать/скрыть)

nikita@terminal ~ $ sudo sensors-detect
[sudo] password for nikita:
# sensors-detect revision 6170 (2013-05-20 21:25:22 +0200)
# Board: Intel Corporation DG43GT

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): yes
Module cpuid loaded successfully.
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
AMD Family 12h and 14h thermal sensors...                   No
AMD Family 15h thermal sensors...                           No
AMD Family 15h power sensors...                             No
AMD Family 16h power sensors...                             No
Intel digital thermal sensor...                             Success!
    (driver `coretemp')
Intel AMB FB-DIMM thermal sensor...                         No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): yes
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               Yes
Found `Winbond W83627DHG-P/W83527HG Super IO Sensors'       Success!
    (address 0x290, driver `w83627ehf')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No

Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): yes
Probing for `IPMI BMC KCS' at 0xca0...                      No
Probing for `IPMI BMC SMIC' at 0xca8...                     No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): yes
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): yes
Using driver `i2c-i801' for device 0000:00:1f.3: Intel ICH10
Module i2c-i801 loaded successfully.
Module i2c-dev loaded successfully.

Next adapter: NVIDIA i2c adapter 0 at 1:00.0 (i2c-0)
Do you want to scan it? (yes/NO/selectively): yes
Client found at address 0x49
Probing for `National Semiconductor LM75'...                No
Probing for `National Semiconductor LM75A'...               No
Probing for `Dallas Semiconductor DS75'...                  No
Probing for `National Semiconductor LM77'...                No
Probing for `Analog Devices ADT7410/ADT7420'...             No
Probing for `Maxim MAX6642'...                              No
Probing for `National Semiconductor LM73'...                No
Probing for `National Semiconductor LM92'...                No
Probing for `National Semiconductor LM76'...                No
Probing for `Maxim MAX6633/MAX6634/MAX6635'...              No
Probing for `NXP/Philips SA56004'...                        No
Probing for `SMSC EMC1023'...                               No
Probing for `SMSC EMC1043'...                               No
Probing for `SMSC EMC1053'...                               No
Probing for `SMSC EMC1063'...                               No

Next adapter: NVIDIA i2c adapter 1 at 1:00.0 (i2c-1)
Do you want to scan it? (yes/NO/selectively): yes

Next adapter: NVIDIA i2c adapter 2 at 1:00.0 (i2c-2)
Do you want to scan it? (yes/NO/selectively): yes

Next adapter: NVIDIA i2c adapter 6 at 1:00.0 (i2c-3)
Do you want to scan it? (yes/NO/selectively): yes

Now follows a summary of the probes I have just done.
Just press ENTER to continue: yes

Driver `coretemp':
  * Chip `Intel digital thermal sensor' (confidence: 9)

Driver `w83627ehf':
  * ISA bus, address 0x290
    Chip `Winbond W83627DHG-P/W83527HG Super IO Sensors' (confidence: 9)

To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
coretemp
w83627ehf
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!

Do you want to add these lines automatically to /etc/modules? (yes/NO)yes
Successful!

Monitoring programs won't work until the needed modules are
loaded. You may want to run 'service kmod start'
to load them.

Unloading i2c-dev... OK
Unloading i2c-i801... OK
Unloading cpuid... OK

[lin_user]

P.S. уже подумываю что реобас всё таки лучше в данной ситуации, но как тогда быть с 0 показателями (каждый раз смотреть через биос нет возможности)

А зачем на них смотреть?

как в такой ситуации мониторить температуры?

Да как обычно.

[v!tax]

http://vladimir-stupin.blogspot.com/2011/11/fancontrol.html
http://www.ubuntu-help.org/2012/03/fancontrol-lm-sensors-linux.html
http://vovanys.com/linux/upravlenie-kulerom-v-ubuntu-pri-pomoshhi-fancontrol/