root@localhost ~]# smartctl -a -s on /dev/sda
smartctl 6.2 2013-07-26 r3841 [i686-linux-3.14.41-std-def-alt1] (ALT Linux 6.2-alt0.M70P.1)
Copyright (C) 2002-13, Bruce Allen, Christian Franke,
www.smartmontools.org=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint P80
Device Model: SAMSUNG SP0842N
Serial Number: S0DWJ30L212226
Firmware Version: BH100-35
User Capacity: 80 026 361 856 bytes [80,0 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 T13/1532D revision 4a
Local Time is: Tue Jun 13 21:24:41 2017 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 32) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 1848) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 30) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 253 099 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always - 2944
4 Start_Stop_Count 0x0032 079 079 000 Old_age Always - 22100
5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 253 253 015 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 12450
10 Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 253 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 089 089 000 Old_age Always - 12028
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 2044070
190 Airflow_Temperature_Cel 0x0022 085 064 045 Old_age Always - 51
194 Temperature_Celsius 0x0022 085 064 000 Old_age Always - 51
195 Hardware_ECC_Recovered 0x001a 253 100 000 Old_age Always - 3
196 Reallocated_Event_Count 0x0032 253 253 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 253 089 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 253 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 099 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 11947 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 11947 occurred at disk power-on lifetime: 12203 hours (508 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 9c b3 96 e1 Error: UNC at LBA = 0x0196b39c = 26653596
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 d8 01 9c b3 96 e1 00 00:09:07.188 READ VERIFY SECTOR(S)
20 d8 01 18 31 b3 e3 00 00:09:07.188 READ SECTOR(S)
40 d8 01 9b b3 96 e1 00 00:09:07.188 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:07.188 READ SECTOR(S)
40 d8 02 9d b3 96 e1 00 00:09:07.188 READ VERIFY SECTOR(S)
Error 11946 occurred at disk power-on lifetime: 12203 hours (508 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 9b b3 96 e1 Error: UNC at LBA = 0x0196b39b = 26653595
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 d8 02 9b b3 96 e1 00 00:09:05.438 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:05.438 READ SECTOR(S)
c6 d8 00 9c b3 96 a0 00 00:09:05.438 SET MULTIPLE MODE
Error 11945 occurred at disk power-on lifetime: 12203 hours (508 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 04 9b b3 96 e1 Error: UNC at LBA = 0x0196b39b = 26653595
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 d8 04 9b b3 96 e1 00 00:09:03.625 READ VERIFY SECTOR(S)
20 d8 01 18 31 b3 e3 00 00:09:03.625 READ SECTOR(S)
40 d8 04 97 b3 96 e1 00 00:09:03.625 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:03.625 READ SECTOR(S)
c6 d8 00 9c b3 96 a0 00 00:09:03.625 SET MULTIPLE MODE
Error 11944 occurred at disk power-on lifetime: 12203 hours (508 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 97 b3 96 e1 Error: UNC at LBA = 0x0196b397 = 26653591
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 d8 08 97 b3 96 e1 00 00:09:01.813 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:01.813 READ SECTOR(S)
40 d8 08 8f b3 96 e1 00 00:09:01.813 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:01.813 READ SECTOR(S)
c6 d8 00 9c b3 96 a0 00 00:09:01.813 SET MULTIPLE MODE
Error 11943 occurred at disk power-on lifetime: 12203 hours (508 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 10 8f b3 96 e1 Error: UNC at LBA = 0x0196b38f = 26653583
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 d8 10 8f b3 96 e1 00 00:09:00.000 READ VERIFY SECTOR(S)
20 d8 01 18 31 b3 e3 00 00:09:00.000 READ SECTOR(S)
40 d8 10 7f b3 96 e1 00 00:09:00.000 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:00.000 READ SECTOR(S)
40 d8 20 9f b3 96 e1 00 00:09:00.000 READ VERIFY SECTOR(S)
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Self-test routine in progress 00% 12448 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[root@localhost ~]# smartctl -a /dev/sda
smartctl 6.2 2013-07-26 r3841 [i686-linux-3.14.41-std-def-alt1] (ALT Linux 6.2-alt0.M70P.1)
Copyright (C) 2002-13, Bruce Allen, Christian Franke,
www.smartmontools.org=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint P80
Device Model: SAMSUNG SP0842N
Serial Number: S0DWJ30L212226
Firmware Version: BH100-35
User Capacity: 80 026 361 856 bytes [80,0 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 T13/1532D revision 4a
Local Time is: Tue Jun 13 21:24:53 2017 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 32) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 1848) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 30) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 253 099 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always - 2944
4 Start_Stop_Count 0x0032 079 079 000 Old_age Always - 22100
5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 253 253 015 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 12450
10 Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 253 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 089 089 000 Old_age Always - 12028
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 2044070
190 Airflow_Temperature_Cel 0x0022 088 064 045 Old_age Always - 50
194 Temperature_Celsius 0x0022 088 064 000 Old_age Always - 50
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 12846
196 Reallocated_Event_Count 0x0032 253 253 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 253 089 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 253 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 099 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 11947 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 11947 occurred at disk power-on lifetime: 12203 hours (508 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 9c b3 96 e1 Error: UNC at LBA = 0x0196b39c = 26653596
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 d8 01 9c b3 96 e1 00 00:09:07.188 READ VERIFY SECTOR(S)
20 d8 01 18 31 b3 e3 00 00:09:07.188 READ SECTOR(S)
40 d8 01 9b b3 96 e1 00 00:09:07.188 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:07.188 READ SECTOR(S)
40 d8 02 9d b3 96 e1 00 00:09:07.188 READ VERIFY SECTOR(S)
Error 11946 occurred at disk power-on lifetime: 12203 hours (508 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 9b b3 96 e1 Error: UNC at LBA = 0x0196b39b = 26653595
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 d8 02 9b b3 96 e1 00 00:09:05.438 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:05.438 READ SECTOR(S)
c6 d8 00 9c b3 96 a0 00 00:09:05.438 SET MULTIPLE MODE
Error 11945 occurred at disk power-on lifetime: 12203 hours (508 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 04 9b b3 96 e1 Error: UNC at LBA = 0x0196b39b = 26653595
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 d8 04 9b b3 96 e1 00 00:09:03.625 READ VERIFY SECTOR(S)
20 d8 01 18 31 b3 e3 00 00:09:03.625 READ SECTOR(S)
40 d8 04 97 b3 96 e1 00 00:09:03.625 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:03.625 READ SECTOR(S)
c6 d8 00 9c b3 96 a0 00 00:09:03.625 SET MULTIPLE MODE
Error 11944 occurred at disk power-on lifetime: 12203 hours (508 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 97 b3 96 e1 Error: UNC at LBA = 0x0196b397 = 26653591
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 d8 08 97 b3 96 e1 00 00:09:01.813 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:01.813 READ SECTOR(S)
40 d8 08 8f b3 96 e1 00 00:09:01.813 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:01.813 READ SECTOR(S)
c6 d8 00 9c b3 96 a0 00 00:09:01.813 SET MULTIPLE MODE
Error 11943 occurred at disk power-on lifetime: 12203 hours (508 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 10 8f b3 96 e1 Error: UNC at LBA = 0x0196b38f = 26653583
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
40 d8 10 8f b3 96 e1 00 00:09:00.000 READ VERIFY SECTOR(S)
20 d8 01 18 31 b3 e3 00 00:09:00.000 READ SECTOR(S)
40 d8 10 7f b3 96 e1 00 00:09:00.000 READ VERIFY SECTOR(S)
20 d8 01 00 00 00 e0 00 00:09:00.000 READ SECTOR(S)
40 d8 20 9f b3 96 e1 00 00:09:00.000 READ VERIFY SECTOR(S)
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Self-test routine in progress 00% 12448 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[/tt]