smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.8.0-56-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org=== START OF INFORMATION SECTION ===
Model Family: SanDisk based SSDs
Device Model: SanDisk SSD U100 16GB
Serial Number: 0b454e3e5
LU WWN Device Id: 5 001b40 054b4e5e3
Firmware Version: KM.10.00
User Capacity: 16.013.942.784 bytes [16,0 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 1.8 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 T13/2015-D revision 3
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Jun 29 09:37:51 2017 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 3) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0002 100 100 000 Old_age Always - 0
9 Power_On_Hours 0x0002 100 100 000 Old_age Always - 2
12 Power_Cycle_Count 0x0002 100 100 000 Old_age Always - 949
171 Program_Fail_Count 0x0002 100 100 000 Old_age Always - 0
172 Erase_Fail_Count 0x0002 100 100 000 Old_age Always - 0
173 Avg_Write/Erase_Count 0x0002 100 100 000 Old_age Always - 9
174 Unexpect_Power_Loss_Ct 0x0002 100 100 000 Old_age Always - 179
187 Reported_Uncorrect 0x0002 100 100 000 Old_age Always - 0
230 Perc_Write/Erase_Count 0x0002 100 100 000 Old_age Always - 30
232 Perc_Avail_Resrvd_Space 0x0003 100 100 005 Pre-fail Always - 0
234 Perc_Write/Erase_Ct_BC 0x0002 100 100 000 Old_age Always - 5
241 Total_LBAs_Written 0x0002 100 100 000 Old_age Always - 29652239
242 Total_LBAs_Read 0x0002 100 100 000 Old_age Always - 30695854
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Тема: usb drive Superblock invalid, trying backup blocks (Прочитано 1491 раз)
