что пишет dmesg после присоединения устройства?
После этой команды пишет очень много, даже все не влезло:
put/input5
[ 1.804620] ata1.00: ATA-6: ST9100822A, 3.01, max UDMA/100
[ 1.804624] ata1.00: 195371568 sectors, multi 16: LBA48
[ 1.804659] ata1.01: ATAPI: MATSHITAUJ-845D, D100, max UDMA/33
[ 1.816015] Clocksource tsc unstable (delta = -204686991 ns)
[ 1.820521] ata1.00: configured for UDMA/100
[ 1.836362] ata1.01: configured for UDMA/33
[ 1.836942] scsi 0:0:0:0: Direct-Access ATA ST9100822A 3.01 PQ: 0 ANSI: 5
[ 1.837044] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.838782] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB)
[ 1.838829] sd 0:0:0:0: [sda] Write Protect is off
[ 1.838832] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.838856] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.838976] sda:
[ 1.839085] scsi 0:0:1:0: CD-ROM MATSHITA UJ-845D D100 PQ: 0 ANSI: 5
[ 1.868163] sda1 sda2 < sda5 >
[ 1.900123] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.902333] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda caddy
[ 1.902337] Uniform CD-ROM driver Revision: 3.20
[ 1.902401] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 1.902440] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 1.902462] Freeing unused kernel memory: 540k freed
[ 1.902763] Write protecting the kernel text: 4568k
[ 1.902799] Write protecting the kernel read-only data: 1836k
[ 2.019688] Linux agpgart interface v0.103
[ 2.076458] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/device:02/input/input6
[ 2.076507] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 2.081138] tg3.c:v3.99 (April 20, 2009)
[ 2.081157] tg3 0000:06:08.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.122925] tg3 0000:06:08.0: wake-up capability disabled by ACPI
[ 2.122933] tg3 0000:06:08.0: PME# disabled
[ 2.268120] [drm] Initialized drm 1.1.0 20060810
[ 2.287931] [drm] radeon default to kernel modesetting DISABLED.
[ 2.288116] pci 0000:01:00.0: power state changed by ACPI to D0
[ 2.288129] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.288135] pci 0000:01:00.0: setting latency timer to 64
[ 2.288280] [drm] Initialized radeon 1.31.0 20080528 for 0000:01:00.0 on minor 0
[ 2.289734] eth0: Tigon3 [partno(BCM95705A50) rev 3003] (PCI:33MHz:32-bit) MAC address 00:c0:9f:bc:4f:a4
[ 2.289739] eth0: attached PHY is 5705 (10/100/1000Base-T Ethernet) (WireSpeed[0])
[ 2.289742] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 2.289744] eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
[ 2.290026] ohci1394 0000:06:01.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 2.344043] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[b0217000-b02177ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 3.058244] xor: automatically using best checksumming function: pIII_sse
[ 3.076005] pIII_sse : 5180.000 MB/sec
[ 3.076008] xor: using function: pIII_sse (5180.000 MB/sec)
[ 3.079215] device-mapper: dm-raid45: initialized v0.2594b
[ 3.249435] PM: Starting manual resume from disk
[ 3.249440] PM: Resume from partition 8:5
[ 3.249442] PM: Checking hibernation image.
[ 3.249592] PM: Resume from disk failed.
[ 3.281802] EXT4-fs (sda1): barriers enabled
[ 3.308069] kjournald2 starting: pid 391, dev sda1:8, commit interval 5 seconds
[ 3.308080] EXT4-fs (sda1): delayed allocation enabled
[ 3.308083] EXT4-fs: file extents enabled
[ 3.310081] EXT4-fs: mballoc enabled
[ 3.310095] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 3.620136] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f000064bd3e]
[ 13.116025] usb 3-2: new low speed USB device using uhci_hcd and address 2
[ 13.344145] usb 3-2: configuration #1 chosen from 1 choice
[ 22.477228] Adding 4016208k swap on /dev/sda5. Priority:-1 extents:1 across:4016208k
[ 22.589283] udev: starting version 147
[ 22.612849] EXT4-fs (sda1): internal journal on sda1:8
[ 22.675818] lp: driver loaded but no devices found
[ 22.676540] irda_init()
[ 22.676555] NET: Registered protocol family 23
[ 22.679383] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
[ 22.679407] nsc-ircc, chip->init
[ 22.679417] nsc-ircc, Found chip at base=0x164e
[ 22.679444] nsc-ircc, driver loaded (Dag Brattli)
[ 22.679451] nsc_ircc_open(), can't get iobase of 0x2f8
[ 22.679482] nsc-ircc, Found chip at base=0x164e
[ 22.679509] nsc-ircc, driver loaded (Dag Brattli)
[ 22.679512] nsc_ircc_open(), can't get iobase of 0x2f8
[ 22.679746] nsc-ircc 00:06: disabled
[ 22.949636] tg3 0000:06:08.0: firmware: requesting tigon/tg3_tso5.bin
[ 22.952816] tg3 0000:06:08.0: wake-up capability disabled by ACPI
[ 22.952823] tg3 0000:06:08.0: PME# disabled
[ 23.244960] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.425020] intel_rng: FWH not detected
[ 23.468333] acer-wmi: Acer Laptop ACPI-WMI Extras
[ 23.468351] acer-wmi: No or unsupported WMI interface, unable to load
[ 23.582555] Intel ICH 0000:00:1e.2: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 23.582583] Intel ICH 0000:00:1e.2: setting latency timer to 64
[ 23.900023] intel8x0_measure_ac97_clock: measured 54167 usecs (2610 samples)
[ 23.900027] intel8x0: clocking to 48000
[ 24.042819] yenta_cardbus 0000:06:01.0: CardBus bridge found [1025:0066]
[ 24.042837] yenta_cardbus 0000:06:01.0: Enabling burst memory read transactions
[ 24.042841] yenta_cardbus 0000:06:01.0: Using CSCINT to route CSC interrupts to PCI
[ 24.042844] yenta_cardbus 0000:06:01.0: Routing CardBus interrupts to PCI
[ 24.042849] yenta_cardbus 0000:06:01.0: TI: mfunc 0x01c21b22, devctl 0x64
[ 24.048102] lib80211: common routines for IEEE802.11 drivers
[ 24.048105] lib80211_crypt: registered algorithm 'NULL'
[ 24.084199] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 24.084202] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 24.094935] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 24.094939] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 24.102982] ttyS1: LSR safety check engaged!
[ 24.218516] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 24.280625] yenta_cardbus 0000:06:01.0: ISA IRQ mask 0x0cf8, PCI irq 18
[ 24.280630] yenta_cardbus 0000:06:01.0: Socket status: 30000006
[ 24.280635] pci_bus 0000:06: Raising subordinate bus# of parent bus (#06) from #07 to #08
[ 24.280644] yenta_cardbus 0000:06:01.0: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
[ 24.280648] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x4000-0x4fff: clean.
[ 24.280861] yenta_cardbus 0000:06:01.0: pcmcia: parent PCI bridge Memory window: 0xb0200000 - 0xb02fffff
[ 24.280864] yenta_cardbus 0000:06:01.0: pcmcia: parent PCI bridge Memory window: 0x80000000 - 0x83ffffff
[ 24.281947] ipw2200 0000:06:03.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 24.282021] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 24.282059] ipw2200 0000:06:03.0: firmware: requesting ipw2200-bss.fw
[ 24.456197] usbcore: registered new interface driver hiddev
[ 24.456256] usbcore: registered new interface driver usbhid
[ 24.456258] usbhid: v2.6:USB HID core driver
[ 24.534031] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
[ 24.535224] tifm_7xx1 0000:06:01.3: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 24.564044] tifm_core: MMC/SD card detected in socket 0:3
[ 24.582584] input: A4Tech USB Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input7
[ 24.582686] a4tech 0003:09DA:000A.0001: input,hidraw0: USB HID v1.10 Mouse [A4Tech USB Mouse] on usb-0000:00:1d.1-2/input0
[ 24.678809] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 24.679973] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 24.680500] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 24.680912] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 24.681459] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 24.754445] mmc0: new SD card at address 9520
[ 24.758697] mmcblk0: mmc0:9520 SU02G 1.89 GiB
[ 24.758757] mmcblk0: p1
[ 24.767943] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x126eb1, caps: 0xa04713/0x4000
[ 24.787063] type=1505 audit(1267585743.682:2): operation="profile_load" pid=1166 name=/usr/share/gdm/guest-session/Xsession
[ 24.788844] type=1505 audit(1267585743.686:3): operation="profile_load" pid=1167 name=/sbin/dhclient3
[ 24.789485] type=1505 audit(1267585743.686:4): operation="profile_load" pid=1167 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 24.789845] type=1505 audit(1267585743.686:5): operation="profile_load" pid=1167 name=/usr/lib/connman/scripts/dhclient-script
[ 24.794555] type=1505 audit(1267585743.690:6): operation="profile_load" pid=1168 name=/usr/bin/evince
[ 24.806629] type=1505 audit(1267585743.702:7): operation="profile_load" pid=1168 name=/usr/bin/evince-previewer
[ 24.811192] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
[ 24.828471] type=1505 audit(1267585743.726:
: operation="profile_load" pid=1168 name=/usr/bin/evince-thumbnailer
[ 24.908966] type=1505 audit(1267585743.806:9): operation="profile_load" pid=1179 name=/usr/bin/freshclam
[ 24.911077] type=1505 audit(1267585743.806:10): operation="profile_load" pid=1180 name=/usr/lib/cups/backend/cups-pdf
[ 24.911827] type=1505 audit(1267585743.806:11): operation="profile_load" pid=1180 name=/usr/sbin/cupsd
[ 29.454596] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 29.454600] vboxdrv: Warning: 2.6.31+ kernel detected. Most likely the hardware performance
[ 29.454602] vboxdrv: counter framework which can generate NMIs is active. You have to prevent
[ 29.454603] vboxdrv: the usage of hardware performance counters by
[ 29.454604] vboxdrv: echo 2 > /proc/sys/kernel/perf_counter_paranoid
[ 29.454608] vboxdrv: Found 1 processor cores.
[ 29.454713] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 29.454716] vboxdrv: Successfully loaded version 3.1.4 (interface 0x00100001).
[ 30.061358] ppdev: user-space parallel port driver
[ 31.169627] __ratelimit: 6 callbacks suppressed
[ 31.169630] ACPI: EC: missing confirmations, switch off interrupt mode.
[ 34.217867] [drm] Setting GART location based on new memory map
[ 34.220056] [drm] Loading R400 Microcode
[ 34.220098] [drm] Num pipes: 2
[ 34.220105] [drm] writeback test succeeded in 1 usecs
[ 35.076015] eth1: no IPv6 routers present
[ 71.485166] gvfs-gdu-volume[2434]: segfault at c ip 0044dfa7 sp bf84266c error 4 in libgdu.so.0.0.0[43b000+31000]
[ 71.723227] gvfs-gdu-volume[2442]: segfault at c ip 00a49fa7 sp bf98162c error 4 in libgdu.so.0.0.0[a37000+31000]
[ 71.917111] lib80211_crypt: registered algorithm 'WEP'
[ 117.812788] chromium-browse[2710]: segfault at 13c ip 08cf0544 sp bf83b880 error 4 in chromium-browser[8048000+225d000]
[ 228.208712] sr 0:0:1:0: [sr0] Unhandled sense code
[ 228.208721] sr 0:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 228.208729] sr 0:0:1:0: [sr0] Sense Key : Medium Error [current]
[ 228.208740] sr 0:0:1:0: [sr0] Add. Sense: No seek complete
[ 228.208750] end_request: I/O error, dev sr0, sector 9180288
[ 228.208761] Buffer I/O error on device sr0, logical block 1147536
[ 229.152061] usb 1-8: new high speed USB device using ehci_hcd and address 3
[ 229.290995] usb 1-8: configuration #1 chosen from 1 choice
[ 235.493153] sr 0:0:1:0: [sr0] Unhandled sense code
[ 235.493162] sr 0:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 235.493171] sr 0:0:1:0: [sr0] Sense Key : Medium Error [current]
[ 235.493181] sr 0:0:1:0: [sr0] Add. Sense: No seek complete
[ 235.493192] end_request: I/O error, dev sr0, sector 9180288
[ 235.493203] Buffer I/O error on device sr0, logical block 1147536
[ 235.550622] Initializing USB Mass Storage driver...
[ 235.553198] scsi2 : SCSI emulation for USB Mass Storage devices
[ 235.553505] usbcore: registered new interface driver usb-storage
[ 235.553513] USB Mass Storage support registered.
[ 235.554561] usb-storage: device found at 3
[ 235.554567] usb-storage: waiting for device to settle before scanning
[ 240.560102] usb-storage: device scan complete
[ 240.560526] scsi 2:0:0:0: Direct-Access ST916082 1AS 3.AL PQ: 0 ANSI: 0
[ 240.560906] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 240.566406] sd 2:0:0:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 240.568769] sd 2:0:0:0: [sdb] Write Protect is off
[ 240.568772] sd 2:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 240.568775] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 240.575485] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 240.575492] sdb: sdb2 < sdb5 >
Пользователь решил продолжить мысль 03 Марта 2010, 13:44:03:
что пишет dmesg после присоединения устройства?
Продолжение
[ 240.620282] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 240.620290] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 242.350018] sr 0:0:1:0: [sr0] Unhandled sense code
[ 242.350027] sr 0:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 242.350036] sr 0:0:1:0: [sr0] Sense Key : Medium Error [current]
[ 242.350046] sr 0:0:1:0: [sr0] Add. Sense: No seek complete
[ 242.350057] end_request: I/O error, dev sr0, sector 9180400
[ 242.350068] Buffer I/O error on device sr0, logical block 1147550
[ 249.205115] sr 0:0:1:0: [sr0] Unhandled sense code
[ 249.205124] sr 0:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 249.205133] sr 0:0:1:0: [sr0] Sense Key : Medium Error [current]
[ 249.205143] sr 0:0:1:0: [sr0] Add. Sense: No seek complete
[ 249.205154] end_request: I/O error, dev sr0, sector 9180400
[ 249.205164] Buffer I/O error on device sr0, logical block 1147550
[ 256.791564] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
[ 435.197204] gvfs-gdu-volume[3040]: segfault at c ip 007cdfa7 sp bfebd25c error 4 in libgdu.so.0.0.0[7bb000+31000]
[ 445.596402] gnome-panel[2380]: segfault at 4 ip 00b8d546 sp bfc002a0 error 4 in libglobalmenu-plugin.so[b7e000+13000]
[ 446.337717] gvfs-gdu-volume[3053]: segfault at c ip 007c1fa7 sp bfe65f8c error 4 in libgdu.so.0.0.0[7af000+31000]
[ 703.984044] usb 1-6: new high speed USB device using ehci_hcd and address 4
[ 704.121858] usb 1-6: configuration #1 chosen from 1 choice
[ 704.124500] hub 1-6:1.0: USB hub found
[ 704.128622] hub 1-6:1.0: 7 ports detected
[ 707.742219] usb 1-8: USB disconnect, address 3
[ 772.524063] usb 1-6: USB disconnect, address 4
[ 786.576072] usb 3-2: USB disconnect, address 2
[ 789.008055] usb 5-2: new low speed USB device using uhci_hcd and address 2
[ 789.180243] usb 5-2: configuration #1 chosen from 1 choice
[ 789.199957] input: A4Tech USB Mouse as /devices/pci0000:00/0000:00:1d.3/usb5/5-2/5-2:1.0/input/input9
[ 789.206203] a4tech 0003:09DA:000A.0002: input,hidraw0: USB HID v1.10 Mouse [A4Tech USB Mouse] on usb-0000:00:1d.3-2/input0
[ 802.556085] usb 1-6: new high speed USB device using ehci_hcd and address 6
[ 802.689151] usb 1-6: configuration #1 chosen from 1 choice
[ 802.691843] scsi3 : SCSI emulation for USB Mass Storage devices
[ 802.694320] usb-storage: device found at 6
[ 802.694327] usb-storage: waiting for device to settle before scanning
[ 807.694410] usb-storage: device scan complete
[ 807.694921] scsi 3:0:0:0: Direct-Access ST916082 1AS 3.AL PQ: 0 ANSI: 0
[ 807.695723] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 807.720901] sd 3:0:0:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 807.724215] sd 3:0:0:0: [sdb] Write Protect is off
[ 807.724220] sd 3:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 807.724223] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 807.728869] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 807.728876] sdb: sdb2 < sdb5 >
[ 807.780386] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 807.780393] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 877.153122] gvfs-gdu-volume[3260]: segfault at c ip 00f4efa7 sp bf8d069c error 4 in libgdu.so.0.0.0[f3c000+31000]
[ 881.881156] usb 1-6: USB disconnect, address 6
[ 885.776073] usb 5-2: USB disconnect, address 2
[ 888.468054] usb 3-2: new low speed USB device using uhci_hcd and address 3
[ 888.641241] usb 3-2: configuration #1 chosen from 1 choice
[ 888.671656] input: A4Tech USB Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input10
[ 888.671756] a4tech 0003:09DA:000A.0003: input,hidraw0: USB HID v1.10 Mouse [A4Tech USB Mouse] on usb-0000:00:1d.1-2/input0
[ 1188.204042] usb 4-2: new full speed USB device using uhci_hcd and address 2
[ 1188.386241] usb 4-2: configuration #1 chosen from 1 choice
[ 1188.450668] cdc_acm 4-2:1.8: ttyACM0: USB ACM device
[ 1188.460610] usbcore: registered new interface driver cdc_acm
[ 1188.460615] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1188.473000] NET: Registered protocol family 35
[ 1188.543925] usbcore: registered new interface driver cdc_ether
[ 1188.634697] usbcore: registered new interface driver cdc_phonet
[ 1188.635978] usb 4-2: bad CDC descriptors
[ 1188.636023] usbcore: registered new interface driver rndis_host
[ 1188.690416] cfg80211: Calling CRDA to update world regulatory domain
[ 1188.712878] usb 4-2: bad CDC descriptors
[ 1188.712932] usbcore: registered new interface driver rndis_wlan
[ 1188.741089] cfg80211: World regulatory domain updated:
[ 1188.741093] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 1188.741096] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1188.741099] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 1188.741102] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 1188.741105] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1188.741108] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1197.801377] PPP BSD Compression module registered
[ 1197.844775] PPP Deflate Compression module registered
[ 1278.068807] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
[ 1509.816046] usb 1-8: new high speed USB device using ehci_hcd and address 9
[ 1510.073392] usb 1-8: configuration #1 chosen from 1 choice
[ 1510.073606] scsi4 : SCSI emulation for USB Mass Storage devices
[ 1510.073712] usb-storage: device found at 9
[ 1510.073715] usb-storage: waiting for device to settle before scanning
[ 1515.072762] usb-storage: device scan complete
[ 1515.073773] scsi 4:0:0:0: Direct-Access JetFlash Transcend 4GB 8.07 PQ: 0 ANSI: 2
[ 1515.074608] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 1515.097851] sd 4:0:0:0: [sdb] 7843840 512-byte logical blocks: (4.01 GB/3.74 GiB)
[ 1515.098596] sd 4:0:0:0: [sdb] Write Protect is off
[ 1515.098599] sd 4:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 1515.098602] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 1515.104634] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 1515.104641] sdb: sdb1
[ 1515.125283] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 1515.125291] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 1557.088055] usb 1-8: reset high speed USB device using ehci_hcd and address 9
[ 1557.437416] scsi5 : SCSI emulation for USB Mass Storage devices
[ 1557.455865] usb-storage: device found at 9
[ 1557.455872] usb-storage: waiting for device to settle before scanning
[ 1562.456882] usb-storage: device scan complete
[ 1562.457547] scsi 5:0:0:0: Direct-Access JetFlash Transcend 4GB 8.07 PQ: 0 ANSI: 2
[ 1562.457957] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 1562.483416] sd 5:0:0:0: [sdb] 7843840 512-byte logical blocks: (4.01 GB/3.74 GiB)
[ 1562.484540] sd 5:0:0:0: [sdb] Write Protect is off
[ 1562.484546] sd 5:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 1562.484549] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 1562.501879] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 1562.501887] sdb: sdb1
[ 1562.524873] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 1562.524883] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[ 2553.276682] usb 1-8: USB disconnect, address 9
[ 2557.309022] usb 5-2: new full speed USB device using uhci_hcd and address 3
[ 2557.738268] usb 5-2: configuration #1 chosen from 1 choice
[ 2557.807583] Bluetooth: Generic Bluetooth USB driver ver 0.5
[ 2557.807740] usbcore: registered new interface driver btusb
[ 2558.051069] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2558.051074] Bluetooth: BNEP filters: protocol multicast
[ 2558.119454] Bridge firewalling registered
[ 2717.256092] usb 5-2: USB disconnect, address 3
[ 2717.257090] btusb_intr_complete: hci0 urb efe6d000 failed to resubmit (19)
[ 2717.257104] btusb_bulk_complete: hci0 urb f2823900 failed to resubmit (19)
[ 2717.258081] btusb_bulk_complete: hci0 urb f24af080 failed to resubmit (19)
[ 2717.259070] btusb_send_frame: hci0 urb d8b85d80 submission failed
[ 2743.644042] usb 1-8: new high speed USB device using ehci_hcd and address 11
[ 2743.886886] usb 1-8: configuration #1 chosen from 1 choice
[ 2743.889808] scsi6 : SCSI emulation for USB Mass Storage devices
[ 2743.890030] usb-storage: device found at 11
[ 2743.890035] usb-storage: waiting for device to settle before scanning
[ 2748.888652] usb-storage: device scan complete
[ 2748.889401] scsi 6:0:0:0: Direct-Access JetFlash Transcend 4GB 8.07 PQ: 0 ANSI: 2
[ 2748.890221] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 2748.913839] sd 6:0:0:0: [sdb] 7843840 512-byte logical blocks: (4.01 GB/3.74 GiB)
[ 2748.915199] sd 6:0:0:0: [sdb] Write Protect is off
[ 2748.915203] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 2748.915206] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 2748.924812] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 2748.924820] sdb: sdb1
[ 2748.943591] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 2748.943598] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 2838.928052] usb 1-8: reset high speed USB device using ehci_hcd and address 11
[ 2839.281373] scsi7 : SCSI emulation for USB Mass Storage devices
[ 2839.293298] usb-storage: device found at 11
[ 2839.293304] usb-storage: waiting for device to settle before scanning
[ 2844.293674] usb-storage: device scan complete
[ 2844.294408] scsi 7:0:0:0: Direct-Access JetFlash Transcend 4GB 8.07 PQ: 0 ANSI: 2
[ 2844.295231] sd 7:0:0:0: Attached scsi generic sg2 type 0
Пользователь решил продолжить мысль 03 Марта 2010, 15:46:03:
что пишет dmesg после присоединения устройства?
Еще много можно добавлять текста из того, что выдала эта команда, добавить?
Тема: Как заставить работать USB устройства? (Прочитано 2251 раз)
