Кнопки ноутбука

[Wweb911]

Здравствуйте! Уважаемые форумчане! Поставил Ubuntu 9.10 на ноутбук Cpmpaq CQ-410ER. На нем есть кнопки) которые не работают под Линукс, чего с ними делать? Прошу помоч)) а именно кнопки включения Wi-Fi и выключения ноута, а также кнопка включения\выключения тачпада

[dimas000]

кгм... для асуса есть некий asus-laptop extras, насчет компака - хз, во всяком случае в конфиге дистрибутивного ядра ничего похожего не нашел. потом поищу в самом ядре, мб чего и есть...
кстати, есть догадки насчет acpi. попробуй грузануть ядро с опцией acpi=off (в грубе выбираешь нужный пункт, жмешь "e", к опциям "quiet splash" дописываешь еще и "acpi=off") - во всяком случае, на вкл/выкл должно как-то повлиять.
ЗЫ. а вообще система выключается?
ЗЗЫ. кнопка вайфая у самого не работает. в биосе - пожалуйста, а при загрузки убунты снова включается намертво. надо смотреть, если модулем - можно его заблокировать, если монолитом вшито - тут уж только ядро пересобирать, но стоит ли оно того?

[Wweb911]

да система выключается, вот вроде щас кнопка включения стала работать стабильно, по крайней мере выполняет свою функцию
а с кнопкой включения выключения тача что делать?

(Нажмите, чтобы показать/скрыть)

[    0.148904] pci 0000:00:14.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.148913] pci 0000:00:14.0: PME# disabled
[    0.149137] pci 0000:00:08.0: transparent bridge
[    0.149169] pci 0000:02:00.0: reg 10 32bit mmio: [0xc1000000-0xc1ffffff]
[    0.149178] pci 0000:02:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
[    0.149186] pci 0000:02:00.0: reg 1c 64bit mmio: [0xc4000000-0xc5ffffff]
[    0.149191] pci 0000:02:00.0: reg 24 io port: [0x4000-0x407f]
[    0.149196] pci 0000:02:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[    0.149240] pci 0000:00:0b.0: bridge io port: [0x4000-0x4fff]
[    0.149244] pci 0000:00:0b.0: bridge 32bit mmio: [0xc1000000-0xc1ffffff]
[    0.149250] pci 0000:00:0b.0: bridge 64bit mmio pref: [0xc4000000-0xdfffffff]
[    0.149305] pci 0000:07:00.0: reg 10 64bit mmio: [0xc2000000-0xc200ffff]
[    0.149436] pci 0000:00:14.0: bridge 32bit mmio: [0xc2000000-0xc20fffff]
[    0.149473] pci_bus 0000:00: on NUMA node 0
[    0.149477] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.149574] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[    0.149665] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IXVE._PRT]
[    0.167795] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 10 11 14 15) *0, disabled.
[    0.167959] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 10 11 14 15) *0, disabled.
[    0.168131] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 10 11 14 15) *0, disabled.
[    0.168293] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 10 11 14 15) *0, disabled.
[    0.168457] ACPI: PCI Interrupt Link [Z012] (IRQs 19 20 21 22 23) *10
[    0.168618] ACPI: PCI Interrupt Link [Z013] (IRQs 19 20 21 22 23) *0, disabled.
[    0.168781] ACPI: PCI Interrupt Link [Z014] (IRQs 19 20 21 22 23) *0, disabled.
[    0.168943] ACPI: PCI Interrupt Link [Z015] (IRQs 19 20 21 22 23) *0, disabled.
[    0.169105] ACPI: PCI Interrupt Link [LSMB] (IRQs 18) *10
[    0.169268] ACPI: PCI Interrupt Link [LUS0] (IRQs 17) *11
[    0.169429] ACPI: PCI Interrupt Link [LUS2] (IRQs 17) *7
[    0.169594] ACPI: PCI Interrupt Link [LMAC] (IRQs 19 20 21 22 23) *11
[    0.169756] ACPI: PCI Interrupt Link [LAZA] (IRQs 19 20 21 22 23) *10
[    0.169918] ACPI: PCI Interrupt Link [LGPU] (IRQs 19 20 21 22 23) *10
[    0.170080] ACPI: PCI Interrupt Link [LPID] (IRQs 19 20 21 22 23) *0, disabled.
[    0.170248] ACPI: PCI Interrupt Link [LSI0] (IRQs 19 20 21 22 23) *11
[    0.170409] ACPI: PCI Interrupt Link [LSI1] (IRQs 19 20 21 22 23) *0, disabled.
[    0.170574] ACPI: PCI Interrupt Link [Z010] (IRQs 16) *5
[    0.170740] ACPI: PCI Interrupt Link [Z011] (IRQs 16) *10
[    0.170899] ACPI: PCI Interrupt Link [LPMU] (IRQs 18) *11
[    0.171065] SCSI subsystem initialized
[    0.171127] libata version 3.00 loaded.
[    0.171197] usbcore: registered new interface driver usbfs
[    0.171209] usbcore: registered new interface driver hub
[    0.171231] usbcore: registered new device driver usb
[    0.171369] ACPI: WMI: Mapper loaded
[    0.171371] PCI: Using ACPI for IRQ routing
[    0.171527] Bluetooth: Core ver 2.15
[    0.171552] NET: Registered protocol family 31
[    0.171554] Bluetooth: HCI device and connection manager initialized
[    0.171557] Bluetooth: HCI socket layer initialized
[    0.171560] NetLabel: Initializing
[    0.171561] NetLabel:  domain hash size = 128
[    0.171563] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.171576] NetLabel:  unlabeled traffic allowed by default
[    0.171605] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[    0.171610] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[    0.177439] pnp: PnP ACPI init
[    0.177460] ACPI: bus type pnp registered
[    0.186237] pnp: PnP ACPI: found 12 devices
[    0.186239] ACPI: ACPI bus type pnp unregistered
[    0.186243] PnPBIOS: Disabled by ACPI PNP
[    0.186254] system 00:02: iomem range 0xe0000000-0xefffffff has been reserved
[    0.186260] system 00:03: ioport range 0x360-0x361 has been reserved
[    0.186263] system 00:03: ioport range 0x4d0-0x4d1 has been reserved
[    0.186267] system 00:03: iomem range 0xff800000-0xff800fff has been reserved
[    0.186273] system 00:0a: ioport range 0x1000-0x107f has been reserved
[    0.186276] system 00:0a: ioport range 0x1080-0x10ff has been reserved
[    0.186279] system 00:0a: ioport range 0x1200-0x127f has been reserved
[    0.186282] system 00:0a: ioport range 0x1280-0x12ff has been reserved
[    0.186285] system 00:0a: ioport range 0x1400-0x147f has been reserved
[    0.186288] system 00:0a: ioport range 0x1480-0x14ff has been reserved
[    0.186293] system 00:0b: iomem range 0xffc00000-0xffffffff could not be reserved
[    0.186297] system 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.186300] system 00:0b: iomem range 0xfee00000-0xfeefffff could not be reserved
[    0.186303] system 00:0b: iomem range 0xfed00000-0xfed00fff has been reserved
[    0.186307] system 00:0b: iomem range 0xfef00000-0xfef00fff has been reserved
[    0.220964] AppArmor: AppArmor Filesystem Enabled
[    0.221007] pci 0000:00:08.0: PCI bridge, secondary bus 0000:01
[    0.221009] pci 0000:00:08.0:   IO window: disabled
[    0.221014] pci 0000:00:08.0:   MEM window: disabled
[    0.221017] pci 0000:00:08.0:   PREFETCH window: disabled
[    0.221024] pci 0000:00:0b.0: PCI bridge, secondary bus 0000:02
[    0.221028] pci 0000:00:0b.0:   IO window: 0x4000-0x4fff
[    0.221032] pci 0000:00:0b.0:   MEM window: 0xc1000000-0xc1ffffff
[    0.221036] pci 0000:00:0b.0:   PREFETCH window: 0x000000c4000000-0x000000dfffffff
[    0.221262] pci 0000:00:14.0: PCI bridge, secondary bus 0000:07
[    0.221265] pci 0000:00:14.0:   IO window: disabled
[    0.221276] pci 0000:00:14.0:   MEM window: 0xc2000000-0xc20fffff
[    0.221283] pci 0000:00:14.0:   PREFETCH window: disabled
[    0.221299] pci 0000:00:08.0: setting latency timer to 64
[    0.221306] pci 0000:00:0b.0: setting latency timer to 64
[    0.221575] ACPI: PCI Interrupt Link [Z012] enabled at IRQ 23
[    0.221579]   alloc irq_desc for 23 on node -1
[    0.221582]   alloc kstat_irqs on node -1
[    0.221591] pci 0000:00:14.0: PCI INT A -> Link[Z012] -> GSI 23 (level, low) -> IRQ 23
[    0.221600] pci 0000:00:14.0: setting latency timer to 64
[    0.221608] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.221610] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.221614] pci_bus 0000:01: resource 3 io:  [0x00-0xffff]
[    0.221616] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffff]
[    0.221619] pci_bus 0000:02: resource 0 io:  [0x4000-0x4fff]
[    0.221622] pci_bus 0000:02: resource 1 mem: [0xc1000000-0xc1ffffff]
[    0.221625] pci_bus 0000:02: resource 2 pref mem [0xc4000000-0xdfffffff]
[    0.221628] pci_bus 0000:07: resource 1 mem: [0xc2000000-0xc20fffff]
[    0.221665] NET: Registered protocol family 2
[    0.221751] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.222070] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.222776] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.223123] TCP: Hash tables configured (established 131072 bind 65536)
[    0.223126] TCP reno registered
[    0.223208] NET: Registered protocol family 1
[    0.223274] Trying to unpack rootfs image as initramfs...
[    0.422780] Freeing initrd memory: 7473k freed
[    0.427594] Simple Boot Flag at 0x38 set to 0x1
[    0.427707] cpufreq-nforce2: No nForce2 chipset.
[    0.427732] Scanning for low memory corruption every 60 seconds
[    0.427836] audit: initializing netlink socket (disabled)
[    0.427854] type=2000 audit(1270898237.424:1): initialized
[    0.436587] highmem bounce pool size: 64 pages
[    0.436596] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.437819] VFS: Disk quotas dquot_6.5.2
[    0.437877] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.438516] fuse init (API version 7.12)
[    0.438603] msgmni has been set to 1686
[    0.438790] alg: No test for stdrng (krng)
[    0.438801] io scheduler noop registered
[    0.438803] io scheduler anticipatory registered
[    0.438805] io scheduler deadline registered
[    0.438845] io scheduler cfq registered (default)
[    0.439083] pci 0000:00:07.0: Enabling HT MSI Mapping
[    0.439206] pci 0000:00:08.0: Enabling HT MSI Mapping
[    0.439342] pci 0000:00:09.0: Enabling HT MSI Mapping
[    0.439485] pci 0000:00:0a.0: Enabling HT MSI Mapping
[    0.439629] pci 0000:00:0b.0: Enabling HT MSI Mapping
[    0.439705] pci 0000:02:00.0: Boot video device
[    0.440034]   alloc irq_desc for 24 on node -1
[    0.440037]   alloc kstat_irqs on node -1
[    0.440059] pcieport-driver 0000:00:14.0: irq 24 for MSI/MSI-X
[    0.440081] pcieport-driver 0000:00:14.0: setting latency timer to 64
[    0.440254] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.440276] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.443933] ACPI: AC Adapter [ADP1] (on-line)
[    0.443990] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    0.443995] ACPI: Power Button [PWRF]
[    0.444056] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[    0.447046] ACPI: Lid Switch [LID0]
[    0.447086] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[    0.447093] ACPI: Sleep Button [SLPB]
[    0.447139] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[    0.447142] ACPI: Power Button [PWRB]
[    0.447369] processor LNXCPU:00: registered as cooling_device0
[    0.487356] thermal LNXTHERM:01: registered as thermal_zone0
[    0.487363] ACPI: Thermal Zone [TZS0] (58 C)
[    0.500749] thermal LNXTHERM:02: registered as thermal_zone1
[    0.500755] ACPI: Thermal Zone [TZS1] (58 C)
[    0.500796] isapnp: Scanning for PnP cards...
[    0.504040] Switched to high resolution mode on CPU 0
[    0.813503] ACPI: Battery Slot [BAT0] (battery absent)
[    0.857001] isapnp: No Plug & Play device found
[    0.858047] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.859208] brd: module loaded
[    0.859627] loop: module loaded
[    0.859713] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[    0.859782] ahci 0000:00:09.0: version 3.0
[    0.860089] ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 22
[    0.860094]   alloc irq_desc for 22 on node -1
[    0.860097]   alloc kstat_irqs on node -1
[    0.860108] ahci 0000:00:09.0: PCI INT A -> Link[LSI0] -> GSI 22 (level, low) -> IRQ 22
[    0.860143]   alloc irq_desc for 25 on node -1
[    0.860145]   alloc kstat_irqs on node -1
[    0.860152] ahci 0000:00:09.0: irq 25 for MSI/MSI-X
[    0.860201] ahci 0000:00:09.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl IDE mode
[    0.860205] ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pmp pio slum part
[    0.860209] ahci 0000:00:09.0: setting latency timer to 64
[    0.860468] scsi0 : ahci
[    0.860565] scsi1 : ahci
[    0.860636] ata1: SATA max UDMA/133 abar m8192@0xc0004000 port 0xc0004100 irq 25
[    0.860639] ata2: SATA max UDMA/133 abar m8192@0xc0004000 port 0xc0004180 irq 25
[    0.860828] pata_amd 0000:00:06.0: version 0.4.1
[    0.860869] pata_amd 0000:00:06.0: setting latency timer to 64
[    0.860963] scsi2 : pata_amd
[    0.861029] scsi3 : pata_amd
[    0.861058] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x30c0 irq 14
[    0.861061] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x30c8 irq 15
[    0.861684] Fixed MDIO Bus: probed
[    0.861718] PPP generic driver version 2.4.2
[    0.861824] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.862130] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 17
[    0.862134]   alloc irq_desc for 17 on node -1
[    0.862136]   alloc kstat_irqs on node -1
[    0.862146] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 17 (level, low) -> IRQ 17
[    0.862163] ehci_hcd 0000:00:02.1: setting latency timer to 64
[    0.862166] ehci_hcd 0000:00:02.1: EHCI Host Controller
[    0.862194] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[    0.862225] ehci_hcd 0000:00:02.1: debug port 1
[    0.862230] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[    0.862249] ehci_hcd 0000:00:02.1: irq 17, io mem 0xc0007000
[    0.872019] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[    0.872097] usb usb1: configuration #1 chosen from 1 choice
[    0.872128] hub 1-0:1.0: USB hub found
[    0.872137] hub 1-0:1.0: 3 ports detected
[    0.872424] ACPI: PCI Interrupt Link [Z011] enabled at IRQ 16
[    0.872427]   alloc irq_desc for 16 on node -1
[    0.872429]   alloc kstat_irqs on node -1
[    0.872437] ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z011] -> GSI 16 (level, low) -> IRQ 16
[    0.872446] ehci_hcd 0000:00:04.1: setting latency timer to 64
[    0.872449] ehci_hcd 0000:00:04.1: EHCI Host Controller
[    0.872478] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
[    0.872504] ehci_hcd 0000:00:04.1: debug port 1
[    0.872509] ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
[    0.872525] ehci_hcd 0000:00:04.1: irq 16, io mem 0xc0007400
[    0.884048] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
[    0.884109] usb usb2: configuration #1 chosen from 1 choice
[    0.884130] hub 2-0:1.0: USB hub found
[    0.884141] hub 2-0:1.0: 4 ports detected
[    0.884183] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.884444] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 17
[    0.884448] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 17 (level, low) -> IRQ 17
[    0.884457] ohci_hcd 0000:00:02.0: setting latency timer to 64
[    0.884460] ohci_hcd 0000:00:02.0: OHCI Host Controller
[    0.884485] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
[    0.884497] ohci_hcd 0000:00:02.0: irq 17, io mem 0xc0006000
[    0.942498] usb usb3: configuration #1 chosen from 1 choice
[    0.942519] hub 3-0:1.0: USB hub found
[    0.942527] hub 3-0:1.0: 3 ports detected
[    0.942809] ACPI: PCI Interrupt Link [Z010] enabled at IRQ 16
[    0.942812] ohci_hcd 0000:00:04.0: PCI INT A -> Link[Z010] -> GSI 16 (level, low) -> IRQ 16
[    0.942820] ohci_hcd 0000:00:04.0: setting latency timer to 64
[    0.942823] ohci_hcd 0000:00:04.0: OHCI Host Controller
[    0.942849] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
[    0.942860] ohci_hcd 0000:00:04.0: irq 16, io mem 0xc0008000
[    0.998123] usb usb4: configuration #1 chosen from 1 choice
[    0.998144] hub 4-0:1.0: USB hub found
[    0.998153] hub 4-0:1.0: 4 ports detected
[    0.998192] uhci_hcd: USB Universal Host Controller Interface driver
[    0.998274] PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.020099] i8042.c: Detected active multiplexing controller, rev 1.1.
[    1.034406] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.034411] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.034415] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.034418] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.034420] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.034473] mice: PS/2 mouse device common for all mice
[    1.034592] rtc_cmos 00:06: RTC can wake from S4
[    1.034628] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    1.034684] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[    1.034806] device-mapper: uevent: version 1.0.3
[    1.034906] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    1.035345] device-mapper: multipath: version 1.1.0 loaded
[    1.035348] device-mapper: multipath round-robin: version 1.0.0 loaded
[    1.035482] EISA: Probing bus 0 at eisa.0
[    1.035488] Cannot allocate resource for EISA slot 1
[    1.035493] Cannot allocate resource for EISA slot 3
[    1.035496] Cannot allocate resource for EISA slot 4
[    1.035509] EISA: Detected 0 cards.
[    1.035549] cpuidle: using governor ladder
[    1.035551] cpuidle: using governor menu
[    1.036024] TCP cubic registered
[    1.036171] NET: Registered protocol family 10
[    1.036564] lo: Disabled Privacy Extensions
[    1.036841] NET: Registered protocol family 17
[    1.036857] Bluetooth: L2CAP ver 2.13
[    1.036859] Bluetooth: L2CAP socket layer initialized
[    1.036861] Bluetooth: SCO (Voice Link) ver 0.6
[    1.036863] Bluetooth: SCO socket layer initialized
[    1.036887] Bluetooth: RFCOMM TTY layer initialized
[    1.036890] Bluetooth: RFCOMM socket layer initialized
[    1.036891] Bluetooth: RFCOMM ver 1.11
[    1.036906] powernow-k8: Found 1 AMD Sempron(tm) SI-42 processors (1 cpu cores) (version 2.20.00)
[    1.036940] powernow-k8:    0 : pstate 0 (2100 MHz)
[    1.036943] powernow-k8:    1 : pstate 1 (1050 MHz)
[    1.037123] Using IPI No-Shortcut mode
[    1.037185] PM: Resume from disk failed.
[    1.037197] registered taskstats version 1
[    1.037317]   Magic number: 6:622:276
[    1.037352] tty tty13: hash matches
[    1.037449] rtc_cmos 00:06: setting system clock to 2010-04-10 11:17:18 UTC (1270898238)
[    1.037453] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.037454] EDD information not available.
[    1.058199] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[    1.185124] usb 1-1: new high speed USB device using ehci_hcd and address 2
[    1.344107] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.344125] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.344846] ata2.00: ATA-8: TOSHIBA MK1655GSX, FG011C, max UDMA/100
[    1.344849] ata2.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    1.346120] ata2.00: configured for UDMA/100
[    1.365271] ata1.00: ATAPI: TSSTcorp CDDVDW TS-L633M, 0200, max UDMA/100
[    1.386388] ata1.00: configured for UDMA/100
[    1.392217] scsi 0:0:0:0: CD-ROM            TSSTcorp CDDVDW TS-L633M  0200 PQ: 0 ANSI: 5
[    1.408199] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.408202] Uniform CD-ROM driver Revision: 3.20
[    1.408287] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    1.408327] sr 0:0:0:0: Attached scsi generic sg0 type 5
[    1.408396] scsi 1:0:0:0: Direct-Access     ATA      TOSHIBA MK1655GS FG01 PQ: 0 ANSI: 5
[    1.408487] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    1.408528] sd 1:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    1.408569] sd 1:0:0:0: [sda] Write Protect is off
[    1.408572] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.408593] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.408693]  sda:
[    1.408767] ata4: port disabled. ignoring.
[    1.477300]  sda1 sda2 < sda5 sda6 >
[    1.517621] sd 1:0:0:0: [sda] Attached SCSI disk
[    1.517638] Freeing unused kernel memory: 540k freed
[    1.518012] Write protecting the kernel text: 4580k
[    1.518042] Write protecting the kernel read-only data: 1840k
[    1.596373] usb 1-1: configuration #1 chosen from 1 choice
[    1.760617] usb 2-2: new high speed USB device using ehci_hcd and address 2
[    1.774273] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[    1.774602] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 21
[    1.774608]   alloc irq_desc for 21 on node -1
[    1.774610]   alloc kstat_irqs on node -1
[    1.774622] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
[    1.774628] forcedeth 0000:00:0a.0: setting latency timer to 64
[    1.874914] Initializing USB Mass Storage driver...
[    1.875022] scsi4 : SCSI emulation for USB Mass Storage devices
[    1.875151] usbcore: registered new interface driver usb-storage
[    1.875154] USB Mass Storage support registered.
[    1.889752] usb-storage: device found at 2
[    1.889756] usb-storage: waiting for device to settle before scanning
[    1.931922] usb 2-2: configuration #1 chosen from 1 choice
[    1.967985] acpi device:13: registered as cooling_device1
[    1.968106] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:10/device:11/input/input6
[    1.968147] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[    2.292460] usb 4-4: new low speed USB device using ohci_hcd and address 2
[    2.293571] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1f:16:e3:bb:4f
[    2.293575] forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt lnktim msi desc-v3
[    2.548091] usb 4-4: configuration #1 chosen from 1 choice
[    2.561528] usbcore: registered new interface driver hiddev
[    2.561591] usbcore: registered new interface driver usbhid
[    2.561593] usbhid: v2.6:USB HID core driver
[    2.678708] input: A4Tech PS/2+USB Mouse as /devices/pci0000:00/0000:00:04.0/usb4/4-4/4-4:1.0/input/input7
[    2.678794] a4tech 0003:09DA:000A.0001: input,hidraw0: USB HID v1.10 Mouse [A4Tech PS/2+USB Mouse] on usb-0000:00:04.0-4/input0
[    3.511800] PM: Starting manual resume from disk
[    3.511805] PM: Resume from partition 8:6
[    3.511807] PM: Checking hibernation image.
[    3.511963] PM: Resume from disk failed.
[    3.542943] EXT4-fs (sda5): barriers enabled
[    3.558052] kjournald2 starting: pid 384, dev sda5:8, commit interval 5 seconds
[    3.558082] EXT4-fs (sda5): delayed allocation enabled
[    3.558086] EXT4-fs: file extents enabled
[    3.559975] EXT4-fs: mballoc enabled
[    3.559990] EXT4-fs (sda5): mounted filesystem with ordered data mode
[    4.334911] type=1505 audit(1270898241.794:2): operation="profile_load" pid=408 name=/usr/share/gdm/guest-session/Xsession
[    4.336988] type=1505 audit(1270898241.798:3): operation="profile_load" pid=409 name=/sbin/dhclient3
[    4.337273] type=1505 audit(1270898241.798:4): operation="profile_load" pid=409 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[    4.337436] type=1505 audit(1270898241.798:5): operation="profile_load" pid=409 name=/usr/lib/connman/scripts/dhclient-script
[    4.388231] type=1505 audit(1270898241.850:6): operation="profile_load" pid=410 name=/usr/bin/evince
[    4.393001] type=1505 audit(1270898241.854:7): operation="profile_load" pid=410 name=/usr/bin/evince-previewer
[    4.395821] type=1505 audit(1270898241.854:: operation="profile_load" pid=410 name=/usr/bin/evince-thumbnailer
[    4.427081] type=1505 audit(1270898241.886:9): operation="profile_load" pid=412 name=/usr/lib/cups/backend/cups-pdf
[    6.888334] usb-storage: device scan complete
[    6.891061] scsi 4:0:0:0: Direct-Access     Generic- Multi-Card       1.00 PQ: 0 ANSI: 0 CCS
[    6.891430] sd 4:0:0:0: Attached scsi generic sg2 type 0
[    6.895542] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[   17.310279] udev: starting version 147
[   17.339020] Adding 827308k swap on /dev/sda6.  Priority:-1 extents:1 across:827308k
[   17.345732] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
[   17.345750] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
[   17.416933] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   17.480037] lp: driver loaded but no devices found
[   17.552554] EXT4-fs (sda5): internal journal on sda5:8
[   17.765080] cfg80211: Calling CRDA to update world regulatory domain
[   17.837873] ath5k 0000:07:00.0: PCI INT A -> Link[Z012] -> GSI 23 (level, low) -> IRQ 23
[   17.837886] ath5k 0000:07:00.0: setting latency timer to 64
[   17.837932] ath5k 0000:07:00.0: registered as 'phy0'
[   18.299873] Linux video capture interface: v2.00
[   18.303092] uvcvideo: Found UVC 1.00 device HP Webcam-101 (064e:a102)
[   18.309090] cfg80211: World regulatory domain updated:
[   18.309094]    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   18.309098]    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   18.309101]    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   18.309103]    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   18.309106]    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   18.309109]    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   18.316285] Linux agpgart interface v0.103
[   18.361231] input: HP Webcam-101 as /devices/pci0000:00/0000:00:04.1/usb2/2-2/2-2:1.0/input/input8
[   18.361282] usbcore: registered new interface driver uvcvideo
[   18.361285] USB Video Class driver (v0.1.0)
[   18.437190] ath: EEPROM regdomain: 0x67
[   18.437194] ath: EEPROM indicates we should expect a direct regpair map
[   18.437199] ath: Country alpha2 being used: 00
[   18.437201] ath: Regpair used: 0x67
[   18.764958] __ratelimit: 6 callbacks suppressed
[   18.764962] type=1505 audit(1270883856.226:12): operation="profile_replace" pid=953 name=/usr/share/gdm/guest-session/Xsession
[   18.766708] type=1505 audit(1270883856.226:13): operation="profile_replace" pid=954 name=/sbin/dhclient3
[   18.769772] type=1505 audit(1270883856.230:14): operation="profile_replace" pid=954 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[   18.769938] type=1505 audit(1270883856.230:15): operation="profile_replace" pid=954 name=/usr/lib/connman/scripts/dhclient-script
[   18.774652] type=1505 audit(1270883856.234:16): operation="profile_replace" pid=955 name=/usr/bin/evince
[   18.779455] type=1505 audit(1270883856.238:17): operation="profile_replace" pid=955 name=/usr/bin/evince-previewer
[   18.783603] type=1505 audit(1270883856.242:18): operation="profile_replace" pid=955 name=/usr/bin/evince-thumbnailer
[   18.789790] type=1505 audit(1270883856.250:19): operation="profile_replace" pid=957 name=/usr/lib/cups/backend/cups-pdf
[   18.790147] type=1505 audit(1270883856.250:20): operation="profile_replace" pid=957 name=/usr/sbin/cupsd
[   18.792322] type=1505 audit(1270883856.254:21): operation="profile_replace" pid=958 name=/usr/sbin/tcpdump
[   18.914105] nvidia: module license 'NVIDIA' taints kernel.
[   18.914109] Disabling lock debugging due to kernel taint
[   19.213805] ip_tables: (C) 2000-2006 Netfilter Core Team
[   19.258636] phy0: Selected rate control algorithm 'minstrel'
[   19.259274] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[   19.319769] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 20
[   19.319775]   alloc irq_desc for 20 on node -1
[   19.319778]   alloc kstat_irqs on node -1
[   19.319790] HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 20 (level, low) -> IRQ 20
[   19.319837] HDA Intel 0000:00:07.0: setting latency timer to 64
[   19.484956] Synaptics Touchpad, model: 1, fw: 7.0, id: 0x1a0b1, caps: 0xd04711/0xa00000
[   19.588836] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input9
[   19.646209] ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 19
[   19.646216]   alloc irq_desc for 19 on node -1
[   19.646219]   alloc kstat_irqs on node -1
[   19.646230] nvidia 0000:02:00.0: PCI INT A -> Link[LGPU] -> GSI 19 (level, low) -> IRQ 19
[   19.646239] nvidia 0000:02:00.0: setting latency timer to 64
[   19.646516] NVRM: loading NVIDIA UNIX x86 Kernel Module  185.18.36  Fri Aug 14 17:18:04 PDT 2009
[   19.679990] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   20.236439] input: HDA NVidia Mic as /devices/pci0000:00/0000:00:07.0/sound/card0/input10
[   20.236523] input: HDA NVidia Mic as /devices/pci0000:00/0000:00:07.0/sound/card0/input11
[   20.236579] input: HDA NVidia Headphone as /devices/pci0000:00/0000:00:07.0/sound/card0/input12
[   20.658425]   alloc irq_desc for 26 on node -1
[   20.658429]   alloc kstat_irqs on node -1
[   20.658442] forcedeth 0000:00:0a.0: irq 26 for MSI/MSI-X
[   20.804734] NET: Registered protocol family 24
[   21.518816] ppdev: user-space parallel port driver
[   31.132021] eth0: no IPv6 routers present
[35765.770065] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[38172.449017] atkbd.c: Unknown key pressed (translated set 2, code 0xd8 on isa0060/serio0).
[38172.449026] atkbd.c: Use 'setkeycodes e058 <keycode>' to make it known.
[38172.455199] atkbd.c: Unknown key released (translated set 2, code 0xd8 on isa0060/serio0).
[38172.455205] atkbd.c: Use 'setkeycodes e058 <keycode>' to make it known.
[42223.775646] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.

(Нажмите, чтобы показать/скрыть)

Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 0bda:0158 Realtek Semiconductor Corp. Mass Stroage Device
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 09da:000a A4 Tech Co., Ltd Port Mouse
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 064e:a102 Suyin Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

[armad]

xserver-xorg-input-synaptics установлен?

похоже что да.

[   19.484956] Synaptics Touchpad, model: 1, fw: 7.0, id: 0x1a0b1, caps: 0xd04711/0xa00000
[   19.588836] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input9

Это твой тачпад.

[Wweb911]

да ставил, но все равно на всякий случай опишите процесс установки, мало ли че не так, я новичек в Линуксе

Это твой тачпад.

да, как заставить работать кнопку?)

[armad]

Нету у меня бука чтобы пробовать (
Попробуй вот это поставить - touchfreeze

Touchfreeze docks in your system tray and disables your touchpad
while typing. It re-enables your touchpad when typing stops, using a
configurable delay time.

Или это - gpointing-device-settings

[Wweb911]

Нету у меня бука чтобы пробовать (
Попробуй вот это поставить - touchfreeze

Touchfreeze docks in your system tray and disables your touchpad
while typing. It re-enables your touchpad when typing stops, using a
configurable delay time.

Или это - gpointing-device-settings

c помощью проги получило его выключить, но как кнопку вкл\выкл сделать?)

[armad]

Запусти программу из терминала, понаблюдай вывод.
Почитай хелп к ней, возможно она понимает команды. Вдруг среди них есть на управление тачпадом.
Можеш глянуть здесь - http://cscott.net/Projects/Synaptics/ - тоже драйвера для тачпада синаптикса

Или жди гуру, может и объявится на форуме.

Да, еще, покажи xorg.conf
Пользователь решил продолжить мысль 10 Апреля 2010, 15:45:08:Еще можешь тут почитать - http://ru.gentoo-wiki.com/wiki/Acer_Aspire_5920G
Это не Ubuntu, но линукс есть линукс

[Wweb911]

Запусти программу из терминала, понаблюдай вывод.
Почитай хелп к ней, возможно она понимает команды. Вдруг среди них есть на управление тачпадом.
Можеш глянуть здесь - http://cscott.net/Projects/Synaptics/ - тоже драйвера для тачпада синаптикса

Или жди гуру, может и объявится на форуме.

Да, еще, покажи xorg.conf
Пользователь решил продолжить мысль 10 Апреля 2010, 15:45:08:Еще можешь тут почитать - http://ru.gentoo-wiki.com/wiki/Acer_Aspire_5920G
Это не Ubuntu, но линукс есть линукс

вообщем он у меня изначально пустой был, а в процессе настройки тача, вернее в попытках вот это туда запихивал

(Нажмите, чтобы показать/скрыть)

Section "ServerLayout"
   Identifier   "Layout0"
   Screen      0 "Default Screen" 0 0
   InputDevice   "Synaptics Touchpad"   "SendCoreEvents"
EndSection

Section "Device"
   Identifier   "Configured Video Device"
EndSection

Section "Monitor"
   Identifier   "Configured Monitor"
EndSection

Section "Screen"
   Identifier   "Default Screen"
   Monitor      "Configured Monitor"
   Device      "Configured Video Device"
EndSection

Section "InputDevice"
   Identifier   "Synaptics Touchpad"
   Driver      "synaptics"
   Option      "SendCoreEvents"   "true"
   Option      "Device"      "/dev/psaux"
   Option      "Protocol"      "auto-dev"
   Option      "SHMConfig"      "true"
EndSection

[armad]

Вот это до конца читал ? http://ru.gentoo-wiki.com/wiki/Acer_Aspire_5920G#.D0.A2.D0.B0.D1.87.D0.BF.D0.B0.D0.B4

[Wweb911]

Вот это до конца читал ? http://ru.gentoo-wiki.com/wiki/Acer_Aspire_5920G#.D0.A2.D0.B0.D1.87.D0.BF.D0.B0.D0.B4

Synaptics) мож мне по инструкции сделать все?) ниче что ноут другой?)

[armad]

Если делать, то вдумчиво. Понимая что и куда пишешь. Иначе только навредишь.

[Wweb911]

ммм... в связи с некоторыми затруднениями по смене ос предложения по теме принимаются дальше
буду рад помощи...
P.S.Wi-Fi запустить удалось, он работает, но кнопка нифига) что жми, что не жми((( хотелось бы иметь возможность управлять им с помощью кнопки... такая же ерунда с тачем... кнопка питания стала работать нормально

[dimas000]

гм... пожамкал свою кнопку вайфая... отклик есть - вот что гласят последние записи в /var/log/syslog:

(Нажмите, чтобы показать/скрыть)

Apr 11 01:21:13 Ulf NetworkManager: <info>  (wlan0): device state change: 3 -> 2 (reason 0)
Apr 11 01:21:13 Ulf NetworkManager: <info>  (wlan0): deactivating device (reason: 0).
Apr 11 01:21:13 Ulf NetworkManager: <info>  Policy set 'Auto eth0' (eth0) as default for routing and DNS.
Apr 11 01:21:13 Ulf NetworkManager: <info>  Wireless now enabled by radio killswitch
Apr 11 01:21:13 Ulf NetworkManager: <info>  (wlan0): bringing up device.
Apr 11 01:21:13 Ulf NetworkManager: <info>  (wlan0): device state change: 2 -> 3 (reason 0)
Apr 11 01:21:13 Ulf kernel: [ 1073.672872] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Apr 11 01:21:13 Ulf NetworkManager: <info>  (wlan0): supplicant interface state:  starting -> ready
Apr 11 01:21:13 Ulf wpa_supplicant[1052]: Failed to initiate AP scan.
Apr 11 01:21:14 Ulf wpa_supplicant[1052]: CTRL-EVENT-SCAN-RESULTS

попробуй аналогично со своими кнопками, мб чего и прояснится. и попробуй грузануться без иксов (загрузив ядро с опцией text), чтоб не портили впечатление всякие гномовские (или чьи там еще) навороты

[Wweb911]

гм... пожамкал свою кнопку вайфая... отклик есть - вот что гласят последние записи в /var/log/syslog:

(Нажмите, чтобы показать/скрыть)

Apr 11 01:21:13 Ulf NetworkManager: <info>  (wlan0): device state change: 3 -> 2 (reason 0)
Apr 11 01:21:13 Ulf NetworkManager: <info>  (wlan0): deactivating device (reason: 0).
Apr 11 01:21:13 Ulf NetworkManager: <info>  Policy set 'Auto eth0' (eth0) as default for routing and DNS.
Apr 11 01:21:13 Ulf NetworkManager: <info>  Wireless now enabled by radio killswitch
Apr 11 01:21:13 Ulf NetworkManager: <info>  (wlan0): bringing up device.
Apr 11 01:21:13 Ulf NetworkManager: <info>  (wlan0): device state change: 2 -> 3 (reason 0)
Apr 11 01:21:13 Ulf kernel: [ 1073.672872] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Apr 11 01:21:13 Ulf NetworkManager: <info>  (wlan0): supplicant interface state:  starting -> ready
Apr 11 01:21:13 Ulf wpa_supplicant[1052]: Failed to initiate AP scan.
Apr 11 01:21:14 Ulf wpa_supplicant[1052]: CTRL-EVENT-SCAN-RESULTS

попробуй аналогично со своими кнопками, мб чего и прояснится. и попробуй грузануться без иксов (загрузив ядро с опцией text), чтоб не портили впечатление всякие гномовские (или чьи там еще) навороты

я ничего не понял) что ты предлогаешь делать) опиши пожалуйста по подробнее)