Конечно в sane он не подерживается
Коды 055f:040b. Формат А3.
Прочел что вроде пакет mustek_usb2 неофициальный поддерживает
http://www.meier-geinitz.de/sane/mustek_usb2-backend/index_ru.htmlСкачал
./configure
make
make install
в папке sane где куча конфигов лежит его конфига нету, но в списке dll.conf значится mustek_usb2. И мана по нем работает.
sane-find-scanner находит сканер
а вот "scanimage -L" говорит No scanners
Куда копать дальше?.. Я так и не понял - встал драйвер или нет. И если встал, чего не подхватывается... Все конечно же под рутом... Ну и xsane под рутом тоже ничего не видит. Ubuntu 9.04
root@techlinux:/usr/local/etc/sane.d# SANE_DEBUG_DLL=255 scanimage -L
[sanei_debug] Setting debug level of dll to 255.
[dll] sane_init: SANE dll backend version 1.0.12 from sane-backends 1.0.21cvs
[dll] sane_init/read_dlld: processing /usr/local/etc/sane.d/dll.d ...
[dll] sane_init/read_dlld: done.
[dll] sane_init/read_config: reading dll.conf
[dll] add_backend: adding backend `mustek'
[dll] add_backend: adding backend `mustek_usb'
[dll] add_backend: adding backend `mustek_usb2'
[dll] sane_get_devices
[dll] load: searching backend `mustek_usb2' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-mustek_usb2.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-mustek_usb2.so.1'
[dll] init: initializing backend `mustek_usb2'
[dll] init: backend `mustek_usb2' is version 1.0.10
[dll] load: searching backend `mustek_usb' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-mustek_usb.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-mustek_usb.so.1'
[dll] init: initializing backend `mustek_usb'
[dll] init: backend `mustek_usb' is version 1.0.18
[dll] load: searching backend `mustek' in `/usr/local/lib/sane'
[dll] load: trying to load `/usr/local/lib/sane/libsane-mustek.so.1'
[dll] load: dlopen()ing `/usr/local/lib/sane/libsane-mustek.so.1'
[dll] init: initializing backend `mustek'
[dll] init: backend `mustek' is version 1.0.138
[dll] sane_get_devices: found 0 devices
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
[dll] sane_exit: exiting
[dll] sane_exit: calling backend `mustek_usb2's exit function
[dll] sane_exit: calling backend `mustek_usb's exit function
[dll] sane_exit: calling backend `mustek's exit function
[dll] sane_exit: finished