sudo smartctl --all /dev/sdb
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is
http://smartmontools.sourceforge.net/=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.11
Device Model: ST3500320AS
Serial Number: 5QM23YRT
Firmware Version: SD15
User Capacity: 500 107 862 016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Mon Oct 26 23:45:49 2009 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 25) The self-test routine was aborted by
the host.
Total time to complete Offline
data collection: ( 642) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 117) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 095 079 006 Pre-fail Always - 170214990
3 Spin_Up_Time 0x0003 095 089 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 938
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 2047
7 Seek_Error_Rate 0x000f 037 037 030 Pre-fail Always - 53631325519147
9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 5047
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 1
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 905
184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 098 098 000 Old_age Always - 2
188 Unknown_Attribute 0x0032 100 041 000 Old_age Always - 2504004338283
189 High_Fly_Writes 0x003a 072 072 000 Old_age Always - 28
190 Airflow_Temperature_Cel 0x0022 058 052 045 Old_age Always - 42 (Lifetime Min/Max 42/42)
194 Temperature_Celsius 0x0022 042 048 000 Old_age Always - 42 (0 18 0 0)
195 Hardware_ECC_Recovered 0x001a 037 029 000 Old_age Always - 170214990
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 32744 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 32744 occurred at disk power-on lifetime: 5046 hours (210 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 00 00 00 00 00 a0 00 01:07:15.142 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 01:07:15.134 IDENTIFY DEVICE
00 00 00 00 00 00 00 04 01:07:14.978 NOP [Abort queued commands]
00 00 00 00 00 00 00 ff 01:07:14.666 NOP [Abort queued commands]
ec 00 01 01 00 00 a0 00 01:06:54.095 IDENTIFY DEVICE
Error 32743 occurred at disk power-on lifetime: 5046 hours (210 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 01:07:15.134 IDENTIFY DEVICE
00 00 00 00 00 00 00 04 01:07:14.978 NOP [Abort queued commands]
00 00 00 00 00 00 00 ff 01:07:14.666 NOP [Abort queued commands]
ec 00 01 01 00 00 a0 00 01:06:54.095 IDENTIFY DEVICE
00 00 00 00 00 00 00 04 01:06:52.082 NOP [Abort queued commands]
Error 32742 occurred at disk power-on lifetime: 5046 hours (210 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 01 01 00 00 a0 00 01:06:54.095 IDENTIFY DEVICE
00 00 00 00 00 00 00 04 01:06:52.082 NOP [Abort queued commands]
00 00 00 00 00 00 00 ff 01:06:47.252 NOP [Abort queued commands]
00 00 00 00 00 00 00 ff 01:06:46.695 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 00:54:57.899 IDENTIFY PACKET DEVICE
Error 32741 occurred at disk power-on lifetime: 5046 hours (210 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 00 00 00 00 00 a0 00 00:54:57.899 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 00:54:57.891 IDENTIFY DEVICE
00 00 00 00 00 00 00 04 00:54:57.735 NOP [Abort queued commands]
00 00 00 00 00 00 00 ff 00:54:57.423 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 00:54:52.424 IDENTIFY PACKET DEVICE
Error 32740 occurred at disk power-on lifetime: 5046 hours (210 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 00:54:57.891 IDENTIFY DEVICE
00 00 00 00 00 00 00 04 00:54:57.735 NOP [Abort queued commands]
00 00 00 00 00 00 00 ff 00:54:57.423 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 00:54:52.424 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 00:54:52.416 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.