Там описано пять вариантов работы со свопом. Вы какой сделали?
Добавил в конец открывшегося файла строку
vm.swappiness=1
(без # в начале, я не программист, но думаю, что # в начале означает, что строка будет воспринята как комментарий).
Вы определитесь сначала, какого эффекта вы хотите добиться.
Хочу, чтобы в раздел подкачки данные записывались только при полном заполнении оперативной памяти. Так как установил систему на SSD диск, думаю, что это для долголетия диска будет критичным фактором.
Чет вы по-ходу наоптимизировали?
arh@arh-P35-S3:~$ cat /etc/fstab
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point> <type> <options> <dump> <pass>
# / was on /dev/sda1 during installation
UUID=3919cb01-8867-422f-bab7-5c32d3cde2c3 / ext4 errors=remount-ro 0 1
# /home was on /dev/sda6 during installation
UUID=2fa1bcb0-9ebe-4cb1-8335-d0e27cad769e /home ext4 defaults 0 2
# swap was on /dev/sda5 during installation
UUID=767162b4-2c48-4c7a-a3d2-32aaac8b832d none swap sw 0 0
/dev/fd0 /media/floppy0 auto rw,user,noauto,exec,utf8 0 0
LABEL=Arhiv /mnt/Arhiv auto nosuid,nodev,nofail,x-gvfs-show 0 0
arh@arh-P35-S3:~$ cat /etc/sysctl.conf
#
# /etc/sysctl.conf - Configuration file for setting system variables
# See /etc/sysctl.d/ for additional system variables.
# See sysctl.conf (5) for information.
#
#kernel.domainname = example.com
# Uncomment the following to stop low-level messages on console
#kernel.printk = 3 4 1 3
##############################################################3
# Functions previously found in netbase
#
# Uncomment the next two lines to enable Spoof protection (reverse-path filter)
# Turn on Source Address Verification in all interfaces to
# prevent some spoofing attacks
#net.ipv4.conf.default.rp_filter=1
#net.ipv4.conf.all.rp_filter=1
# Uncomment the next line to enable TCP/IP SYN cookies
# See http://lwn.net/Articles/277146/
# Note: This may impact IPv6 TCP sessions too
#net.ipv4.tcp_syncookies=1
# Uncomment the next line to enable packet forwarding for IPv4
#net.ipv4.ip_forward=1
# Uncomment the next line to enable packet forwarding for IPv6
# Enabling this option disables Stateless Address Autoconfiguration
# based on Router Advertisements for this host
#net.ipv6.conf.all.forwarding=1
###################################################################
# Additional settings - these settings can improve the network
# security of the host and prevent against some network attacks
# including spoofing attacks and man in the middle attacks through
# redirection. Some network environments, however, require that these
# settings are disabled so review and enable them as needed.
#
# Do not accept ICMP redirects (prevent MITM attacks)
#net.ipv4.conf.all.accept_redirects = 0
#net.ipv6.conf.all.accept_redirects = 0
# _or_
# Accept ICMP redirects only for gateways listed in our default
# gateway list (enabled by default)
# net.ipv4.conf.all.secure_redirects = 1
#
# Do not send ICMP redirects (we are not a router)
#net.ipv4.conf.all.send_redirects = 0
#
# Do not accept IP source route packets (we are not a router)
#net.ipv4.conf.all.accept_source_route = 0
#net.ipv6.conf.all.accept_source_route = 0
#
# Log Martian Packets
#net.ipv4.conf.all.log_martians = 1
#
vm.swappiness=1
arh@arh-P35-S3:~$
Пользователь добавил сообщение 01 Февраля 2017, 07:36:30:
Сейчас раздел подкачки пуст, но после работы более 12-ти часов без перезагрузки данные начинают там постепенно накапливаться. Я не знаю, возможно, это нормально?