Стоит Ubuntu 16.04. Используется как сервер хранения. В системе стоят три диска WD два по 500 гб и один 2 Тб
Из них создан LVM раздел на 2.5 ТБ для хранения.
С недавнего времени заметил что очень часто постоянно горит лампа hdd. Вчера зашел в консоль и решил проверить fsck ФС
И вот что получилось -
фото удаленоsmartctl выдает следующее
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 174 172 021 Pre-fail Always - 4266
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 754
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 3300
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 754
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 46
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 707
194 Temperature_Celsius 0x0022 119 095 000 Old_age Always - 28
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 36331 inconsistent with error log pointer 3
ATA Error Count: 36331 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 36331 occurred at disk power-on lifetime: 3300 hours (137 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 10 c8 e1 4b e1 Error: IDNF at LBA = 0x014be1c8 = 21750216
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 10 c8 e1 4b e1 00 01:40:01.777 WRITE DMA
ca 00 08 c0 e1 4b e1 00 01:39:50.294 WRITE DMA
ca 00 18 a8 e1 4b e1 00 01:39:50.251 WRITE DMA
Error 36330 occurred at disk power-on lifetime: 3300 hours (137 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 08 00 a8 07 e0 Error: IDNF at LBA = 0x0007a800 = 501760
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 08 00 a8 07 e0 00 01:39:06.984 WRITE DMA
ca 00 08 88 e1 4b e1 00 01:38:33.561 WRITE DMA
ca 00 30 58 e1 4b e1 00 01:38:33.305 WRITE DMA
Error 36329 occurred at disk power-on lifetime: 3300 hours (137 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 48 08 e1 4b e1 Error: IDNF at LBA = 0x014be108 = 21750024
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ca 00 48 08 e1 4b e1 00 01:37:24.926 WRITE DMA
ca 00 08 00 e1 4b e1 00 01:36:58.421 WRITE DMA
ca 00 10 f0 e0 4b e1 00 01:36:58.410 WRITE DMA
Error 36328 occurred at disk power-on lifetime: 3293 hours (137 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 01 00 00 00 e0 Device Fault; Error: ABRT 1 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 00 07:41:16.135 READ DMA
ef 03 42 00 00 00 a0 00 07:41:16.126 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 07:41:16.115 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 00 05:18:25.284 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 05:18:25.284 SET FEATURES [Set transfer mode]
Error 36327 occurred at disk power-on lifetime: 3293 hours (137 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 42 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 42 00 00 00 a0 00 07:41:16.126 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 07:41:16.115 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 00 05:18:25.284 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 05:18:25.284 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 05:18:25.284 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Что все это означает ? Накрылся диск ? обидно что это как раз WD 2 Tb RED
пп. 1.5. Для добавления графических изображений в сообщения требуется использовать внешние сервисы. Включение в сообщение полноразмерных изображений, превышающих разрешённые размеры, допускается исключительно в виде превью... Руководстве по добавлению изображений на форумОтредактировал
-mahinist