wlan0 вместо eth2

[prestonia]

Код: [Выделить]

maestro@meniac:~$ sudo iwconfig
eth0      no wireless extensions.

eth2      IEEE 802.11abg  ESSID:off/any 
          Mode:Managed  Access Point: Not-Associated   Tx-Power=200 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
         
lo        no wireless extensions.
вместо eth2 должно показываться по идее wlan0 (это встроенный вайфай на ноутбуке)
как быть?

[victor00000]

Код: [Выделить]

cat  /etc/udev/rules.d/70-persistent-net.rules

[prestonia]

Код: [Выделить]

cat  /etc/udev/rules.d/70-persistent-net.rules

Код: [Выделить]

maestro@meniac:~$ cat  /etc/udev/rules.d/70-persistent-net.rules
# This file was automatically generated by the /lib/udev/write_net_rules
# program, run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single
# line, and change only the value of the NAME= key.

# PCI device 0x10ec:/sys/devices/pci0000:00/0000:00:1c.4/0000:07:00.0 (r8169)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:24:e8:fb:61:15", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"

# PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1c.3/0000:06:00.0/ssb0:0 (b43-pci-bridge)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:16:44:d9:57:f2", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"

# PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1c.3/0000:06:00.0 (wl)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:16:44:d9:57:f2", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"

# PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1c.3/0000:06:00.0 (wl)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:16:44:d9:57:f2", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth2"

# USB device 0x0cf3:0x7015 (usb)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="f4:ec:38:96:b3:42", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan1"

# USB device 0x0b05:0x421f (usb)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="80:00:60:0f:e8:00", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth3"

# USB device 0x07d1:0x3c11 (usb)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:21:91:51:98:90", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan2"


[victor00000]

eth2 где? папробуй менять wlan0 и ребеут.