dmesg:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.24-19-rt (buildd@terranova) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP PREEMPT RT Sat Jul 12 02:53:01 UTC 2008 (Ubuntu 2.6.24-4.6-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
[ 0.000000] BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 127MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 262128) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 262128
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 262128
[ 0.000000] On node 0 totalpages: 262128
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4040 pages, LIFO batch:0
[ 0.000000] Normal zone: 3080 pages used for memmap
[ 0.000000] Normal zone: 222200 pages, LIFO batch:31
[ 0.000000] HighMem zone: 447 pages used for memmap
[ 0.000000] HighMem zone: 32305 pages, LIFO batch:7
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F6B00 checksum 0
[ 0.000000] ACPI: RSDP 000F6B00, 0014 (r0 Nvidia)
[ 0.000000] ACPI: RSDT 3FFF3000, 002C (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP 3FFF3040, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT 3FFF30C0, 48E8 (r1 NVIDIA AWRDACPI 1000 MSFT 100000D)
[ 0.000000] ACPI: FACS 3FFF0000, 0040
[ 0.000000] ACPI: APIC 3FFF79C0, 005A (r1 Nvidia AWRDACPI 42302E31 AWRD 0)
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:10 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: BIOS IRQ0 pin2 override ignored.
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[ 0.000000] Real-Time Preemption Support (C) 2004-2007 Ingo Molnar
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 258545
[ 0.000000] Kernel command line: root=/dev/sda1 ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2205.018 MHz processor.
[ 26.993312] Console: colour VGA+ 80x25
[ 26.993316] console [tty0] enabled
[ 26.993847] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 26.994286] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 27.032409] Memory: 1020568k/1048512k available (2225k kernel code, 27248k reserved, 1059k data, 368k init, 131008k highmem)
[ 27.032417] virtual kernel memory layout:
[ 27.032418] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 27.032419] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 27.032420] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 27.032422] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 27.032423] .init : 0xc043b000 - 0xc0497000 ( 368 kB)
[ 27.032424] .data : 0xc032c6a0 - 0xc0435324 (1059 kB)
[ 27.032425] .text : 0xc0100000 - 0xc032c6a0 (2225 kB)
[ 27.032428] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 27.092503] Calibrating delay using timer specific routine.. 4411.82 BogoMIPS (lpj=2205913)
[ 27.092547] Security Framework initialized
[ 27.092555] SELinux: Disabled at boot.
[ 27.092565] AppArmor: AppArmor initialized
[ 27.092569] Failure registering capabilities with primary security module.
[ 27.092585] Mount-cache hash table entries: 512
[ 27.092742] Initializing cgroup subsys ns
[ 27.092748] Initializing cgroup subsys cpuacct
[ 27.092759] CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000 00000000
[ 27.092768] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 27.092770] CPU: L2 Cache: 512K (64 bytes/line)
[ 27.092773] CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000 00000000
[ 27.092783] Compat vDSO mapped to ffffe000.
[ 27.092797] Checking 'hlt' instruction... OK.
[ 27.096735] SMP alternatives: switching to UP code
[ 27.097659] Freeing SMP alternatives: 9k freed
[ 27.097782] Early unpacking initramfs... done
[ 27.414861] ACPI: Core revision 20070126
[ 27.414948] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 27.435595] CPU0: AMD Athlon(tm) XP 3200+ stepping 00
[ 27.435623] Total of 1 processors activated (4411.82 BogoMIPS).
[ 27.435816] ENABLING IO-APIC IRQs
[ 27.436010] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 27.547535] Brought up 1 CPUs
[ 27.547567] CPU0 attaching sched-domain:
[ 27.547570] domain 0: span 01
[ 27.547572] groups: 01
[ 27.547800] net_namespace: 76 bytes
[ 27.547806] Booting paravirtualized kernel on bare hardware
[ 27.548310] Time: 7:51:20 Date: 08/18/08
[ 27.548351] NET: Registered protocol family 16
[ 27.548590] EISA bus registered
[ 27.548618] ACPI: bus type pci registered
[ 27.549193] PCI: PCI BIOS revision 2.10 entry at 0xfb420, last bus=2
[ 27.549196] PCI: Using configuration type 1
[ 27.549200] Setting up standard PCI resources
[ 27.555018] ACPI: EC: Look up EC in DSDT
[ 27.560586] ACPI: Interpreter enabled
[ 27.560589] ACPI: (supports S0 S1 S4 S5)
[ 27.560603] ACPI: Using IOAPIC for interrupt routing
[ 27.568439] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 27.569421] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 27.569572] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 27.569783] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[ 27.613012] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 27.613163] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 27.613307] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 27.613461] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 27.613608] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 27.613754] ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 27.613898] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 27.614052] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 27.614202] ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 27.614352] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 27.614494] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 27.614642] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 27.614786] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 27.614932] ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 27.615086] ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 27.615231] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 27.615356] ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
[ 27.615467] ACPI: PCI Interrupt Link [APC2] (IRQs *17)
[ 27.615580] ACPI: PCI Interrupt Link [APC3] (IRQs *18)
[ 27.615694] ACPI: PCI Interrupt Link [APC4] (IRQs *19)
[ 27.615805] ACPI: PCI Interrupt Link [APCE] (IRQs *16), disabled.
[ 27.615967] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0
[ 27.616136] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0
[ 27.616295] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0
[ 27.616453] ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0
[ 27.616614] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0
[ 27.616772] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
[ 27.616884] ACPI: PCI Interrupt Link [APCS] (IRQs *23)
[ 27.617049] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0
[ 27.617210] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0
[ 27.617370] ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
[ 27.617528] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
[ 27.617672] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 27.617710] pnp: PnP ACPI init
[ 27.617718] ACPI: bus type pnp registered
[ 27.621942] pnp: PnP ACPI: found 15 devices
[ 27.621944] ACPI: ACPI bus type pnp unregistered
[ 27.621948] PnPBIOS: Disabled by ACPI PNP
[ 27.622232] PCI: Using ACPI for IRQ routing
[ 27.622237] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 27.670949] NET: Registered protocol family 8
[ 27.670951] NET: Registered protocol family 20
[ 27.671054] AppArmor: AppArmor Filesystem Enabled
[ 27.682970] system 00:00: ioport range 0x4000-0x407f has been reserved
[ 27.682973] system 00:00: ioport range 0x4080-0x40ff has been reserved
[ 27.682976] system 00:00: ioport range 0x4400-0x447f has been reserved
[ 27.682979] system 00:00: ioport range 0x4480-0x44ff has been reserved
[ 27.682982] system 00:00: ioport range 0x4200-0x427f has been reserved
[ 27.682984] system 00:00: ioport range 0x4280-0x42ff has been reserved
[ 27.682991] system 00:01: ioport range 0x5000-0x503f has been reserved
[ 27.682993] system 00:01: ioport range 0x5100-0x513f has been reserved
[ 27.683000] system 00:02: iomem range 0xd9200-0xdbfff has been reserved
[ 27.683003] system 00:02: iomem range 0xf0000-0xf7fff could not be reserved
[ 27.683006] system 00:02: iomem range 0xf8000-0xfbfff could not be reserved
[ 27.683008] system 00:02: iomem range 0xfc000-0xfffff could not be reserved
[ 27.683011] system 00:02: iomem range 0x3fff0000-0x3fffffff could not be reserved
[ 27.683014] system 00:02: iomem range 0xffff0000-0xffffffff could not be reserved
[ 27.683017] system 00:02: iomem range 0x0-0x9ffff could not be reserved
[ 27.683019] system 00:02: iomem range 0x100000-0x3ffeffff could not be reserved
[ 27.683022] system 00:02: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 27.683025] system 00:02: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 27.683030] system 00:04: ioport range 0xb78-0xb7b has been reserved
[ 27.683033] system 00:04: ioport range 0xf78-0xf7b has been reserved
[ 27.683036] system 00:04: ioport range 0xa78-0xa7b has been reserved
[ 27.683038] system 00:04: ioport range 0xe78-0xe7b has been reserved
[ 27.683040] system 00:04: ioport range 0xbbc-0xbbf has been reserved
[ 27.683043] system 00:04: ioport range 0xfbc-0xfbf has been reserved
[ 27.683045] system 00:04: ioport range 0x4d0-0x4d1 has been reserved
[ 27.683048] system 00:04: ioport range 0x294-0x297 has been reserved
[ 27.713496] PCI: Bridge: 0000:00:08.0
[ 27.713499] IO window: 9000-afff
[ 27.713503] MEM window: cb000000-ccffffff
[ 27.713507] PREFETCH window: 50000000-500fffff
[ 27.713512] PCI: Bridge: 0000:00:1e.0
[ 27.713513] IO window: disabled.
[ 27.713517] MEM window: c8000000-caffffff
[ 27.713520] PREFETCH window: c0000000-c7ffffff
[ 27.713531] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 27.713550] NET: Registered protocol family 2
[ 27.748959] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 27.749318] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 27.750802] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes)
[ 27.753664] TCP: Hash tables configured (established 131072 bind 65536)
[ 27.753670] TCP reno registered
[ 27.765025] checking if image is initramfs... it is
[ 28.365789] Freeing initrd memory: 7801k freed
[ 28.366566] audit: initializing netlink socket (disabled)
[ 28.366583] audit(1219045881.203:1): initialized
[ 28.366699] krcupreemptd setsched 0
[ 28.366701] prio = 98
[ 28.366780] highmem bounce pool size: 64 pages
[ 28.366846] VFS: Disk quotas dquot_6.5.1
[ 28.366870] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 28.366958] io scheduler noop registered
[ 28.366960] io scheduler anticipatory registered
[ 28.366962] io scheduler deadline registered
[ 28.366971] io scheduler cfq registered (default)
[ 28.414579] Boot video device is 0000:02:00.0
[ 28.414885] isapnp: Scanning for PnP cards...
[ 28.772132] isapnp: No Plug & Play device found
[ 28.806033] Real Time Clock Driver v1.12ac
[ 28.806170] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 28.806329] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 28.806505] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 28.807114] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 28.807581] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 28.808449] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 28.808524] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 28.808630] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 28.811037] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 28.811043] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 28.819377] mice: PS/2 mouse device common for all mice
[ 28.819512] EISA: Probing bus 0 at eisa.0
[ 28.819536] Cannot allocate resource for EISA slot 4
[ 28.819539] Cannot allocate resource for EISA slot 5
[ 28.819555] EISA: Detected 0 cards.
[ 28.819558] cpuidle: using governor ladder
[ 28.819649] NET: Registered protocol family 1
[ 28.819676] Using IPI No-Shortcut mode
[ 28.819733] registered taskstats version 1
[ 28.819856] Magic number: 4:444:875
[ 28.820033] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 28.820035] EDD information not available.
[ 28.820430] Freeing unused kernel memory: 368k freed
[ 28.841222] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 30.043265] fuse init (API version 7.9)
[ 30.049483] ACPI: Fan [FAN] (on)
[ 30.058628] ACPI: Thermal Zone [THRM] (45 C)
[ 31.075736] usbcore: registered new interface driver usbfs
[ 31.075765] usbcore: registered new interface driver hub
[ 31.086133] usbcore: registered new device driver usb
[ 31.095976] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[ 31.096308] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
[ 31.096317] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 22 (level, high) -> IRQ 16
[ 31.096324] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 31.111656] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 31.167399] SCSI subsystem initialized
[ 31.248539] libata version 3.00 loaded.
[ 31.431328] FDC 0 is a post-1991 82077
[ 31.609717] forcedeth 0000:00:04.0: ifname eth0, PHY OUI 0x20 @ 1, addr 00:50:8d:f5:55:fc
[ 31.609724] forcedeth 0000:00:04.0: timirq lnktim desc-v1
[ 31.610492] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
[ 31.610501] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, high) -> IRQ 17
[ 31.610515] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 31.610519] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 31.610863] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 31.612320] ohci_hcd 0000:00:02.0: irq 17, io mem 0xcd080000
[ 31.665439] usb usb1: configuration #1 chosen from 1 choice
[ 31.665468] hub 1-0:1.0: USB hub found
[ 31.665482] hub 1-0:1.0: 3 ports detected
[ 31.766642] ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
[ 31.766653] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 20 (level, high) -> IRQ 18
[ 31.766670] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 31.766674] ohci_hcd 0000:00:02.1: OHCI Host Controller
[ 31.766701] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
[ 31.767779] ohci_hcd 0000:00:02.1: irq 18, io mem 0xcd083000
[ 31.822240] usb usb2: configuration #1 chosen from 1 choice
[ 31.822268] hub 2-0:1.0: USB hub found
[ 31.822282] hub 2-0:1.0: 3 ports detected
[ 31.923521] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
[ 31.923529] ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 22 (level, high) -> IRQ 16
[ 31.923546] PCI: Setting latency timer of device 0000:00:02.2 to 64
[ 31.923550] ehci_hcd 0000:00:02.2: EHCI Host Controller
[ 31.923578] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
[ 31.923614] ehci_hcd 0000:00:02.2: debug port 1
[ 31.923619] PCI: cache line size of 64 is not supported by device 0000:00:02.2
[ 31.924688] ehci_hcd 0000:00:02.2: irq 16, io mem 0xcd086000
[ 32.027993] usb 1-2: new full speed USB device using ohci_hcd and address 2
[ 32.033984] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 32.034121] usb usb3: configuration #1 chosen from 1 choice
[ 32.034150] hub 3-0:1.0: USB hub found
[ 32.034160] hub 3-0:1.0: 6 ports detected
[ 32.135645] ACPI: PCI Interrupt Link [APCM] enabled at IRQ 21
[ 32.135652] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [APCM] -> GSI 21 (level, high) -> IRQ 17
[ 32.135659] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 32.195756] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[cd084000-cd0847ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 32.204870] sata_sil 0000:01:0b.0: version 2.3
[ 32.205133] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[ 32.205142] ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 19
[ 32.209994] scsi0 : sata_sil
[ 32.210877] scsi1 : sata_sil
[ 32.210926] ata1: SATA max UDMA/100 mmio m512@0xcc000000 tf 0xcc000080 irq 19
[ 32.210930] ata2: SATA max UDMA/100 mmio m512@0xcc000000 tf 0xcc0000c0 irq 19
[ 32.396726] usb 3-2: new high speed USB device using ehci_hcd and address 2
[ 32.512112] usb 3-2: configuration #1 chosen from 1 choice
[ 32.512407] hub 3-2:1.0: USB hub found
[ 32.513148] hub 3-2:1.0: 4 ports detected
[ 32.664564] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 32.684898] ata1.00: ATA-7: WDC WD5000AAKS-22TMA0, 12.01C01, max UDMA/133
[ 32.684902] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 32.691349] ata1.00: configured for UDMA/100
[ 33.144226] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 33.163752] ata2.00: ATA-8: WDC WD5000AAKS-22A7B0, 01.03B01, max UDMA/133
[ 33.163756] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 33.169751] ata2.00: configured for UDMA/100
[ 33.169892] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKS-2 12.0 PQ: 0 ANSI: 5
[ 33.170406] scsi 1:0:0:0: Direct-Access ATA WDC WD5000AAKS-2 01.0 PQ: 0 ANSI: 5
[ 33.170838] pata_amd 0000:00:09.0: version 0.3.10
[ 33.170918] PCI: Setting latency timer of device 0000:00:09.0 to 64
[ 33.172745] scsi2 : pata_amd
[ 33.176194] scsi3 : pata_amd
[ 33.176814] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 33.176817] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 33.185651] Driver 'sd' needs updating - please use bus_type methods
[ 33.185755] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 33.185770] sd 0:0:0:0: [sda] Write Protect is off
[ 33.185774] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 33.185793] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.185850] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 33.185861] sd 0:0:0:0: [sda] Write Protect is off
[ 33.185864] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 33.185881] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.185886] sda: sda1 sda2 < sda5 > sda3
[ 33.312144] ohci1394: fw-host0: SelfID received outside of bus reset sequence
[ 33.316215] sd 0:0:0:0: [sda] Attached SCSI disk
[ 33.316300] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[ 33.316316] sd 1:0:0:0: [sdb] Write Protect is off
[ 33.316319] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 33.316339] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.316387] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[ 33.316398] sd 1:0:0:0: [sdb] Write Protect is off
[ 33.316401] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 33.316418] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.316421] sdb: sdb1 sdb2 < sdb5 > sdb3
[ 33.364666] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 33.374112] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 33.374135] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 33.481364] ata3.00: ATAPI: PLEXTOR DVDR PX-712A, 1.09, max MWDMA2
[ 33.569032] ieee1394: Host added: ID:BUS[0-00:1023] GUID[000000508df455fc]
[ 33.635206] ata3.00: configured for MWDMA2
[ 33.856222] ata4.00: ATA-6: ST3120026A, 3.06, max UDMA/100
[ 33.856228] ata4.00: 234441648 sectors, multi 16: LBA48
[ 33.878105] ata4.00: configured for UDMA/100
[ 33.878842] scsi 2:0:0:0: CD-ROM PLEXTOR DVDR PX-712A 1.09 PQ: 0 ANSI: 5
[ 33.878930] scsi 2:0:0:0: Attached scsi generic sg2 type 5
[ 33.879446] scsi 3:0:0:0: Direct-Access ATA ST3120026A 3.06 PQ: 0 ANSI: 5
[ 33.879510] sd 3:0:0:0: [sdc] 234441648 512-byte hardware sectors (120034 MB)
[ 33.879525] sd 3:0:0:0: [sdc] Write Protect is off
[ 33.879528] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 33.879547] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.879704] sd 3:0:0:0: [sdc] 234441648 512-byte hardware sectors (120034 MB)
[ 33.879716] sd 3:0:0:0: [sdc] Write Protect is off
[ 33.879719] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 33.879735] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.879738] sdc: sdc1 sdc2 < sdc5 >
[ 33.890623] sd 3:0:0:0: [sdc] Attached SCSI disk
[ 33.890650] sd 3:0:0:0: Attached scsi generic sg3 type 0
[ 33.910447] Driver 'sr' needs updating - please use bus_type methods
[ 33.913363] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 33.913370] Uniform CD-ROM driver Revision: 3.20
[ 33.913431] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 39.288134] EXT3-fs: mounted filesystem with journal data mode.
[ 39.288217] kjournald starting. Commit interval 5 seconds
[ 45.160460] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 45.205302] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 46.180129] Linux agpgart interface v0.102
[ 46.232195] agpgart: Detected NVIDIA nForce2 chipset
[ 46.453415] agpgart: AGP aperture is 512M @ 0xa0000000
[ 46.453480] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000
[ 46.453499] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5100
[ 46.670898] input: Power Button (FF) as /devices/virtual/input/input2
[ 46.682750] ACPI: Power Button (FF) [PWRF]
[ 46.682863] input: Power Button (CM) as /devices/virtual/input/input3
[ 46.694738] ACPI: Power Button (CM) [PWRB]
[ 49.264956] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 49.306213] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 49.490968] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 50.215843] gameport: EMU10K1 is pci0000:01:09.1/gameport0, io 0x9400, speed 59659kHz
[ 50.438454] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 50.438465] ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17 (level, high) -> IRQ 20
[ 50.776827] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5
[ 51.172887] nvidia: module license 'NVIDIA' taints kernel.
[ 51.240220] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
[ 51.240227] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 20 (level, high) -> IRQ 18
[ 51.240259] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 51.265236] parport_pc 00:0c: reported by Plug and Play ACPI
[ 51.265356] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 51.554334] intel8x0_measure_ac97_clock: measured 50774 usecs
[ 51.554340] intel8x0: clocking to 47477
[ 51.859491] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 51.859502] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 21
[ 51.859887] NVRM: loading NVIDIA UNIX x86 Kernel Module 169.12 Thu Feb 14 17:53:07 PST 2008
[ 52.102850] NET: Registered protocol family 10
[ 52.103131] lo: Disabled Privacy Extensions
[ 53.926556] loop: module loaded
[ 53.960758] lp0: using parport0 (interrupt-driven).
[ 54.113990] Adding 2048276k swap on /dev/sda3. Priority:-1 extents:1 across:2048276k
[ 54.479016] EXT3 FS on sda1, internal journal
[ 54.612135] device-mapper: uevent: version 1.0.3
[ 54.612180] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
[ 56.298560] kjournald starting. Commit interval 5 seconds
[ 56.298940] EXT3 FS on sda5, internal journal
[ 56.298946] EXT3-fs: mounted filesystem with journal data mode.
[ 56.323368] kjournald starting. Commit interval 5 seconds
[ 56.331013] EXT3 FS on sdb1, internal journal
[ 56.331017] EXT3-fs: mounted filesystem with journal data mode.
[ 56.353147] kjournald starting. Commit interval 5 seconds
[ 56.353275] EXT3 FS on sdc5, internal journal
[ 56.353279] EXT3-fs: mounted filesystem with ordered data mode.
[ 56.984344] PPP generic driver version 2.4.2
[ 57.000809] NET: Registered protocol family 17
[ 57.456844] NET: Registered protocol family 24
[ 57.949810] No dock devices found.
[ 59.845943] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 59.845950] apm: overridden by ACPI.
[ 59.984644] ppdev: user-space parallel port driver
[ 60.066446] audit(1219038713.209:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=6062 profile="/usr/sbin/cupsd" namespace="default"
[ 62.700012] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[ 62.700027] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[ 62.700098] agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
[ 62.753020] eth0: no IPv6 routers present
[ 163.077309] kjournald starting. Commit interval 5 seconds
[ 163.085292] EXT3 FS on sdb5, internal journal
[ 163.085299] EXT3-fs: mounted filesystem with journal data mode.