вроде как подняли
cherepok@admin:~$ modprobe -c | grep 1969 | grep 2048
alias pci:v00001969d00002048sv*sd*bc*sc*i* atl2
cherepok@admin:~$ sudo rmmod atl2
cherepok@admin:~$ sudo modprobe atl2
cherepok@admin:~$ sudo ifconfig eth0 192.168.111.1 up
cherepok@admin:~$ dmesg | tail -20
[ 320.081027] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 321.651376] atl2: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 321.651665] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 331.968019] eth0: no IPv6 routers present
[ 537.232013] eth0: no IPv6 routers present
[ 640.224014] eth0: no IPv6 routers present
[ 698.288015] eth0: no IPv6 routers present
[ 748.544015] eth0: no IPv6 routers present
[ 823.360009] eth0: no IPv6 routers present
[ 873.120021] eth0: no IPv6 routers present
[ 929.844206] atl2 0000:01:00.0: PCI INT A disabled
[ 937.322929] Atheros(R) L2 Ethernet Driver - version 2.2.3
[ 937.322935] Copyright (c) 2007 Atheros Corporation.
[ 937.322989] atl2 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 937.323007] atl2 0000:01:00.0: setting latency timer to 64
[ 937.370851] atl2 0000:01:00.0: irq 42 for MSI/MSI-X
[ 937.373575] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 938.832782] atl2: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 938.833071] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 949.840017] eth0: no IPv6 routers present
eth0 Link encap:Ethernet HWaddr 00:13:74:00:5c:38
inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::213:74ff:fe00:5c38/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:900 errors:0 dropped:15 overruns:0 frame:0
TX packets:320 errors:0 dropped:0 overruns:0 carrier:2
collisions:0 txqueuelen:1000
RX bytes:94704 (94.7 KB) TX bytes:43986 (43.9 KB)
Memory:febc0000-fec00000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:26960 errors:0 dropped:0 overruns:0 frame:0
TX packets:26960 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2163680 (2.1 MB) TX bytes:2163680 (2.1 MB)
Пользователь решил продолжить мысль 23 Октября 2011, 10:23:42:
теперь осталось поднять ppoe
у меня оптика и она работает через ppoe подключения.
а как понять я не знаю