Не определяется Flash USB

[ArcFi]

danval, партедом её оприходуйте.

[danval]

danval, партедом её оприходуйте.

В смысле?
Почитал на багз.ланчпэд, пробывал разные варианты, не берёт её бациллу.

[dj--alex]

по ходу у меня не монтируются вообще любые другие харды пошел создавать отдельную тему.
из этой мои посты можете удалить

[danval]

Приносили мне другой флешак, так он без проблем монтируется. А мой зараза не хочет и всё.

[danval]

Решилось собственной сборкой ядра 2.6.30.8. 

[tolstyh_aleksey]

Приносили мне другой флешак, так он без проблем монтируется. А мой зараза не хочет и всё.

Линукс Кингстон не любит почему-то.

[$oft]

У меня на УНР такая же проблема... вообще не видет юсб устройств которые подключаются после загрузки системы. на кUbuntu нетбукремикс тоже самое. Вставляю флешку и ничего в /dev не появляется нового... если флешка воткнута до загрузки ос, то появляется диск /dev/sdb1

флешка не подает никаких признаков доступа к ней. флешка рабочая.

Нужно что-то вроде плаг энд плей как в винде... иногда юсб работает нормально. приходится перезагружаться чтобы собственно заработало. хз почему после перезагрузки либо включаются юсб либо нет. Соя жизнь у юсб. Windows на моем MSI wind U120 всё определяет.
___________________
Вот после очередной перезагрузки юсб начало работать нормально. Тут заметил странную особенность:

после фставки флешки юсб автомонтируется в /media/MY FLASH и собственно появляется файл флешки  /dev/sdb1

lsusb:

(Нажмите, чтобы показать/скрыть)

evgeny@evgeny-laptop:~$ lsusb
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 0458:003a KYE Systems Corp. (Mouse Systems)
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 006: ID 090c:1000 Feiya Technology Corp. Flash Drive
Bus 001 Device 005: ID 8086:0180 Intel Corp.
Bus 001 Device 004: ID 0bda:0158 Realtek Semiconductor Corp. Mass Stroage Device
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

dmesg:

(Нажмите, чтобы показать/скрыть)

evgeny@evgeny-laptop:~$ dmesg
[    0.000000] Linux version 2.6.31-14-generic (buildd@rothera) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu8) ) #48-Ubuntu SMP Fri Oct 16 14:04:26 UTC 2009 (Ubuntu 2.6.31-14.48-generic)
[    0.000000] KERNEL supported cpus:
...
[    0.310073] SCSI subsystem initialized
[    0.310156] libata version 3.00 loaded.
[    0.310156] usbcore: registered new interface driver usbfs
[    0.310156] usbcore: registered new interface driver hub
[    0.310156] usbcore: registered new device driver usb
[    0.310156] ACPI: WMI: Mapper loaded
[    0.310156] PCI: Using ACPI for IRQ routing
...

[    0.775486] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[    0.775628] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
...
[    0.775812] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
...
[    0.779268] ACPI: Sleep Button [SLPB]
[    0.780511] ACPI: SSDT 3f5e8c90 00253 (v02  PmRef  Cpu0Ist 00003000 INTL 20051117)
[    0.781403] ACPI: SSDT 3f5e7690 00653 (v02  PmRef  Cpu0Cst 00003001 INTL 20051117)
...
[    1.314453] PPP generic driver version 2.4.2
[    1.314664] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.314709]   alloc irq_desc for 23 on node -1
[    1.314715]   alloc kstat_irqs on node -1
[    1.314727] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    1.314755] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    1.314762] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    1.314865] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    1.318784] ehci_hcd 0000:00:1d.7: debug port 1
[    1.318795] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    1.318823] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xdff40000
[    1.332028] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.332214] usb usb1: configuration #1 chosen from 1 choice
[    1.332280] hub 1-0:1.0: USB hub found
[    1.332298] hub 1-0:1.0: 8 ports detected
[    1.332429] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.332474] uhci_hcd: USB Universal Host Controller Interface driver
[    1.332546] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    1.332561] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    1.332567] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.332651] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    1.332688] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e080
[    1.332867] usb usb2: configuration #1 chosen from 1 choice
[    1.332934] hub 2-0:1.0: USB hub found
[    1.332949] hub 2-0:1.0: 2 ports detected
[    1.333044] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.333055] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    1.333062] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.333137] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    1.333183] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e060
[    1.333366] usb usb3: configuration #1 chosen from 1 choice
[    1.333426] hub 3-0:1.0: USB hub found
[    1.333445] hub 3-0:1.0: 2 ports detected
[    1.333532] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    1.333545] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    1.333552] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.333624] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    1.333667] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e040
[    1.333830] usb usb4: configuration #1 chosen from 1 choice
[    1.333890] hub 4-0:1.0: USB hub found
[    1.333905] hub 4-0:1.0: 2 ports detected
[    1.333998] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    1.334009] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    1.334016] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    1.334082] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    1.334125] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e020
[    1.334294] usb usb5: configuration #1 chosen from 1 choice
[    1.334356] hub 5-0:1.0: USB hub found
[    1.334371] hub 5-0:1.0: 2 ports detected
[    1.334485] i8042: PNP detection disabled
...
[    1.501591]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[    1.503392] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.503437] Freeing unused kernel memory: 540k freed
[    1.503942] Write protecting the kernel text: 4568k
[    1.504094] Write protecting the kernel read-only data: 1836k
[    1.652113] usb 1-1: new high speed USB device using ehci_hcd and address 2
[    1.808848] usb 1-1: configuration #1 chosen from 1 choice
[    1.824038] Clocksource tsc unstable (delta = -130045595 ns)
[    1.841240] atkbd.c: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[    1.841251] atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
[    1.844353] acpi device:1c: registered as cooling_device2
[    1.844648] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:1a/input/input6
[    1.844753] ACPI: Video Device [IGD] (multi-head: yes  rom: no  post: no)
...
[    1.925628] Linux agpgart interface v0.103
[    1.936504] agpgart-intel 0000:00:00.0: Intel 945GME Chipset
[    1.936833] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[    1.977327] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[    1.988965] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.989009] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.989076] r8169 0000:01:00.0: setting latency timer to 64
[    1.989143]   alloc irq_desc for 26 on node -1
[    1.989151]   alloc kstat_irqs on node -1
[    1.989179] r8169 0000:01:00.0: irq 26 for MSI/MSI-X
[    1.991049] eth0: RTL8102e at 0xf80aa000, 00:24:21:6d:96:13, XID 34a00000 IRQ 26
[    2.006333] usb 1-6: new high speed USB device using ehci_hcd and address 4
[    2.030830] Initializing USB Mass Storage driver...
[    2.031130] scsi2 : SCSI emulation for USB Mass Storage devices
[    2.031370] usbcore: registered new interface driver usb-storage
[    2.031381] USB Mass Storage support registered.
[    2.031585] usb-storage: device found at 2
[    2.031591] usb-storage: waiting for device to settle before scanning
[    2.117495] [drm] Initialized drm 1.1.0 20060810
[    2.154732] usb 1-6: configuration #1 chosen from 1 choice
[    2.162242] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    2.162253] i915 0000:00:02.0: setting latency timer to 64
[    2.165448] scsi3 : SCSI emulation for USB Mass Storage devices
[    2.176430] usb-storage: device found at 4
[    2.176437] usb-storage: waiting for device to settle before scanning
[    2.268218] integrated sync not supported
[    2.293052] usb 1-8: new high speed USB device using ehci_hcd and address 5
[    2.387535] integrated sync not supported
[    2.392778] [drm] fb0: inteldrmfb frame buffer device
[    2.392795] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    2.428959] usb 1-8: configuration #1 chosen from 1 choice
[    2.668044] usb 3-1: new low speed USB device using uhci_hcd and address 2
[    2.719361] [drm] LVDS-8: set mode 1024x600 e
[    2.842461] usb 3-1: configuration #1 chosen from 1 choice
[    2.870759] usbcore: registered new interface driver hiddev
[    2.884889] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input7
[    2.885109] generic-usb 0003:0458:003A.0001: input,hidraw0: USB HID v1.10 Mouse [Genius Optical Mouse] on usb-0000:00:1d.1-1/input0
[    2.885150] usbcore: registered new interface driver usbhid
[    2.885158] usbhid: v2.6:USB HID core driver
[    3.136591] Console: switching to colour frame buffer device 128x37
...
[    6.606567] EXT4-fs (sda3): mounted filesystem with ordered data mode
[    7.029363] usb-storage: device scan complete
[    7.030362] scsi 2:0:0:0: Direct-Access     USB 2.0  Flash Disk       1100 PQ: 0 ANSI: 0 CCS
[    7.031414] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    7.035626] sd 2:0:0:0: [sdb] 4062208 512-byte logical blocks: (2.07 GB/1.93 GiB)
[    7.039025] sd 2:0:0:0: [sdb] Write Protect is off
[    7.039039] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
[    7.039047] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    7.042949] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    7.042967]  sdb: sdb1
[    7.047348] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    7.047384] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[    7.072239] type=1505 audit(1262733556.211:2): operation="profile_load" pid=401 name=/sbin/dhclient3
[    7.072824] type=1505 audit(1262733556.211:3): operation="profile_load" pid=401 name=/usr/lib/NetworkManager/nm-dhcp-client.action
...
[    7.181074] usb-storage: device scan complete
[    7.189583] scsi 3:0:0:0: Direct-Access     Generic- Multi-Card       1.00 PQ: 0 ANSI: 0 CCS
[    7.190703] sd 3:0:0:0: Attached scsi generic sg2 type 0
[    7.194822] sd 3:0:0:0: [sdc] Attached SCSI removable disk
[    7.754346] Adding 1156640k swap on /dev/sda5.  Priority:-1 extents:1 across:1156640k
[    7.892581] EXT4-fs (sda3): internal journal on sda3:8
[    8.298227] udev: starting version 147
[    9.744306] cfg80211: Calling CRDA to update world regulatory domain
[   10.177770] intel_rng: FWH not detected
[   10.607206] lp: driver loaded but no devices found
[   10.735672] i2400m_usb 1-8:1.0: firmware: requesting i2400m-fw-usb-1.4.sbcf
[   10.856129] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27k
...
[   10.894586]   alloc kstat_irqs on node -1
[   10.894616] iwlagn 0000:02:00.0: irq 27 for MSI/MSI-X
[   11.003726] psmouse serio1: ID: 10 00 64
[   11.172373] cfg80211: World regulatory domain updated:
[   11.172381]    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
...
[   11.529212] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.655810] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input8
[   11.925041] phy0: Selected rate control algorithm 'iwl-agn-rs'
[   12.273563] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   12.273638] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   12.536297] hda_codec: Unknown model for ALC888, trying auto-probe from BIOS...
[   12.536469] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
[   13.432572] i2400m_usb 1-8:1.0: firmware interface version 9.2.0
[   13.440161] i2400m_usb 1-8:1.0: WiMAX interface wmx0 (00:1d:e1:05:13:7d) ready
[   13.440377] usbcore: registered new interface driver i2400m_usb
[   13.449959] i2400m_usb 1-8:1.0: 'RF Control' (0x4602) command failed: -84 - invalid state (3)
[   13.606482] r8169: eth0: link down
[   13.606905] ADDRCONF(NETDEV_UP): eth0: link is not ready
...
[   13.961233] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   13.964627] ADDRCONF(NETDEV_UP): wmx0: link is not ready
[   15.672304] type=1505 audit(1262722764.811:11): operation="profile_replace" pid=1055 name=/sbin/dhclient3
[   15.673145] type=1505 audit(1262722764.811:12): operation="profile_replace" pid=1055 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[   15.673629] type=1505 audit(1262722764.811:13): operation="profile_replace" pid=1055 name=/usr/lib/connman/scripts/dhclient-script
...
[  395.114254] usb 1-1: USB disconnect, address 2
[  399.028122] usb 1-1: new high speed USB device using ehci_hcd and address 6
[  399.162694] usb 1-1: configuration #1 chosen from 1 choice
[  399.164996] scsi4 : SCSI emulation for USB Mass Storage devices
[  399.172418] usb-storage: device found at 6
[  399.172435] usb-storage: waiting for device to settle before scanning
[  404.172429] usb-storage: device scan complete
[  404.173598] scsi 4:0:0:0: Direct-Access     USB 2.0  Flash Disk       1100 PQ: 0 ANSI: 0 CCS
[  404.175746] sd 4:0:0:0: Attached scsi generic sg1 type 0
[  404.190123] sd 4:0:0:0: [sdb] 4062208 512-byte logical blocks: (2.07 GB/1.93 GiB)
[  404.194638] sd 4:0:0:0: [sdb] Write Protect is off
[  404.194651] sd 4:0:0:0: [sdb] Mode Sense: 43 00 00 00
[  404.194659] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[  404.201612] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[  404.201625]  sdb: sdb1
[  404.259574] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[  404.259602] sd 4:0:0:0: [sdb] Attached SCSI removable disk

А теперь странность. Когда флешку отмонтирую, то сразу пропадает файл /dev/sdb1 и собственно наутилус вообще ее перестает наблюдать и я не знаю где искать признаки присутствия флешки. может кто подскажет?

lsusb видит флеху:

(Нажмите, чтобы показать/скрыть)

evgeny@evgeny-laptop:~$ lsusb
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 0458:003a KYE Systems Corp. (Mouse Systems)
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 006: ID 090c:1000 Feiya Technology Corp. Flash Drive
Bus 001 Device 005: ID 8086:0180 Intel Corp.
Bus 001 Device 004: ID 0bda:0158 Realtek Semiconductor Corp. Mass Stroage Device
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

dmesg тут плохо разбираюсь:

(Нажмите, чтобы показать/скрыть)

evgeny@evgeny-laptop:~$ dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.31-14-generic (buildd@rothera) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu8) ) #48-Ubuntu SMP Fri Oct 16 14:04:26 UTC 2009 (Ubuntu 2.6.31-14.48-generic)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
...
[    0.004101] AppArmor: AppArmor initialized
[    0.004115] Mount-cache hash table entries: 512
...
[    0.004504] Checking 'hlt' instruction... OK.
[    0.024022] ACPI: Core revision 20090521
[    0.038795] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[    0.078489] CPU0: Intel(R) Atom(TM) CPU N270   @ 1.60GHz stepping 02
[    0.080001] Booting processor 1 APIC 0x1 ip 0x6000
[    0.004000] Initializing CPU#1
[    0.004000] Calibrating delay using timer specific routine.. 3200.19 BogoMIPS (lpj=6400383)
...
[    0.168480] EISA bus registered
[    0.168480] ACPI: bus type pci registered
[    0.255262] PCI: Using configuration type 1 for base access
[    0.257495] bio: create slab <bio-0> at 0
[    0.257495] ACPI: EC: Look up EC in DSDT
[    0.265096] ACPI: BIOS _OSI(Linux) query ignored
...
[    0.288263] ACPI: EC: driver started in interrupt mode
[    0.288666] ACPI: No dock devices found.
[    0.289212] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.289365] pci 0000:00:02.0: reg 10 32bit mmio: [0xdfe80000-0xdfefffff]
...
[    0.310073] SCSI subsystem initialized
[    0.310156] libata version 3.00 loaded.
[    0.310156] usbcore: registered new interface driver usbfs
[    0.310156] usbcore: registered new interface driver hub
[    0.310156] usbcore: registered new device driver usb
[    0.310156] ACPI: WMI: Mapper loaded
[    0.310156] PCI: Using ACPI for IRQ routing
...
[    0.320309] hpet clockevent registered
[    0.320316] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.320325] hpet0: at MMIO 0xfed03000, IRQs 2, 8, 0
[    0.320337] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.340026] pnp: PnP ACPI init
[    0.340068] ACPI: bus type pnp registered
[    0.344345] pnp: PnP ACPI: found 11 devices
[    0.344352] ACPI: ACPI bus type pnp unregistered
[    0.344360] PnPBIOS: Disabled by ACPI PNP
...
[    1.314453] PPP generic driver version 2.4.2
[    1.314664] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.314709]   alloc irq_desc for 23 on node -1
[    1.314715]   alloc kstat_irqs on node -1
[    1.314727] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    1.314755] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    1.314762] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    1.314865] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    1.318784] ehci_hcd 0000:00:1d.7: debug port 1
[    1.318795] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    1.318823] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xdff40000
[    1.332028] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.332214] usb usb1: configuration #1 chosen from 1 choice
[    1.332280] hub 1-0:1.0: USB hub found
[    1.332298] hub 1-0:1.0: 8 ports detected
[    1.332429] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.332474] uhci_hcd: USB Universal Host Controller Interface driver
[    1.332546] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    1.332561] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    1.332567] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.332651] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    1.332688] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e080
[    1.332867] usb usb2: configuration #1 chosen from 1 choice
[    1.332934] hub 2-0:1.0: USB hub found
[    1.332949] hub 2-0:1.0: 2 ports detected
[    1.333044] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.333055] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    1.333062] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.333137] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    1.333183] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e060
[    1.333366] usb usb3: configuration #1 chosen from 1 choice
[    1.333426] hub 3-0:1.0: USB hub found
[    1.333445] hub 3-0:1.0: 2 ports detected
[    1.333532] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    1.333545] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    1.333552] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.333624] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    1.333667] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e040
[    1.333830] usb usb4: configuration #1 chosen from 1 choice
[    1.333890] hub 4-0:1.0: USB hub found
[    1.333905] hub 4-0:1.0: 2 ports detected
[    1.333998] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    1.334009] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    1.334016] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    1.334082] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    1.334125] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e020
[    1.334294] usb usb5: configuration #1 chosen from 1 choice
[    1.334356] hub 5-0:1.0: USB hub found
[    1.334371] hub 5-0:1.0: 2 ports detected
...
[    1.354811] EISA: Probing bus 0 at eisa.0
[    1.354850] EISA: Detected 0 cards.
...
[    1.652113] usb 1-1: new high speed USB device using ehci_hcd and address 2
[    1.808848] usb 1-1: configuration #1 chosen from 1 choice
[    1.824038] Clocksource tsc unstable (delta = -130045595 ns)
[    1.841240] atkbd.c: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[    1.841251] atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
[    1.844353] acpi device:1c: registered as cooling_device2
...
[    1.925628] Linux agpgart interface v0.103
[    1.936504] agpgart-intel 0000:00:00.0: Intel 945GME Chipset
[    1.936833] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[    1.977327] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[    1.988965] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.989009] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.989076] r8169 0000:01:00.0: setting latency timer to 64
[    1.989143]   alloc irq_desc for 26 on node -1
[    1.989151]   alloc kstat_irqs on node -1
[    1.989179] r8169 0000:01:00.0: irq 26 for MSI/MSI-X
[    1.991049] eth0: RTL8102e at 0xf80aa000, 00:24:21:6d:96:13, XID 34a00000 IRQ 26
[    2.006333] usb 1-6: new high speed USB device using ehci_hcd and address 4
[    2.030830] Initializing USB Mass Storage driver...
[    2.031130] scsi2 : SCSI emulation for USB Mass Storage devices
[    2.031370] usbcore: registered new interface driver usb-storage
[    2.031381] USB Mass Storage support registered.
[    2.031585] usb-storage: device found at 2
[    2.031591] usb-storage: waiting for device to settle before scanning
[    2.117495] [drm] Initialized drm 1.1.0 20060810
[    2.154732] usb 1-6: configuration #1 chosen from 1 choice
[    2.162242] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    2.162253] i915 0000:00:02.0: setting latency timer to 64
[    2.165448] scsi3 : SCSI emulation for USB Mass Storage devices
[    2.176430] usb-storage: device found at 4
[    2.176437] usb-storage: waiting for device to settle before scanning
[    2.268218] integrated sync not supported
[    2.293052] usb 1-8: new high speed USB device using ehci_hcd and address 5
[    2.387535] integrated sync not supported
[    2.392778] [drm] fb0: inteldrmfb frame buffer device
[    2.392795] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    2.428959] usb 1-8: configuration #1 chosen from 1 choice
[    2.668044] usb 3-1: new low speed USB device using uhci_hcd and address 2
[    2.719361] [drm] LVDS-8: set mode 1024x600 e
[    2.842461] usb 3-1: configuration #1 chosen from 1 choice
[    2.870759] usbcore: registered new interface driver hiddev
[    2.884889] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input7
[    2.885109] generic-usb 0003:0458:003A.0001: input,hidraw0: USB HID v1.10 Mouse [Genius Optical Mouse] on usb-0000:00:1d.1-1/input0
[    2.885150] usbcore: registered new interface driver usbhid
[    2.885158] usbhid: v2.6:USB HID core driver
[    3.136591] Console: switching to colour frame buffer device 128x37
...
[    7.029363] usb-storage: device scan complete
[    7.030362] scsi 2:0:0:0: Direct-Access     USB 2.0  Flash Disk       1100 PQ: 0 ANSI: 0 CCS
[    7.031414] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    7.035626] sd 2:0:0:0: [sdb] 4062208 512-byte logical blocks: (2.07 GB/1.93 GiB)
[    7.039025] sd 2:0:0:0: [sdb] Write Protect is off
[    7.039039] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
[    7.039047] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    7.042949] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    7.042967]  sdb: sdb1
[    7.047348] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[    7.047384] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[    7.072239] type=1505 audit(1262733556.211:2): operation="profile_load" pid=401 name=/sbin/dhclient3
[    7.072824] type=1505 audit(1262733556.211:3): operation="profile_load" pid=401 name=/usr/lib/NetworkManager/nm-dhcp-client.action
...
[    7.181074] usb-storage: device scan complete
[    7.189583] scsi 3:0:0:0: Direct-Access     Generic- Multi-Card       1.00 PQ: 0 ANSI: 0 CCS
[    7.190703] sd 3:0:0:0: Attached scsi generic sg2 type 0
[    7.194822] sd 3:0:0:0: [sdc] Attached SCSI removable disk
[    7.754346] Adding 1156640k swap on /dev/sda5.  Priority:-1 extents:1 across:1156640k
[    7.892581] EXT4-fs (sda3): internal journal on sda3:8
[    8.298227] udev: starting version 147
[    9.744306] cfg80211: Calling CRDA to update world regulatory domain
[   10.177770] intel_rng: FWH not detected
[   10.607206] lp: driver loaded but no devices found
[   10.735672] i2400m_usb 1-8:1.0: firmware: requesting i2400m-fw-usb-1.4.sbcf
...
[   10.894577]   alloc irq_desc for 27 on node -1
[   10.894586]   alloc kstat_irqs on node -1
[   10.894616] iwlagn 0000:02:00.0: irq 27 for MSI/MSI-X
[   11.003726] psmouse serio1: ID: 10 00 64
[   11.172373] cfg80211: World regulatory domain updated:
...
[   12.536469] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
[   13.432572] i2400m_usb 1-8:1.0: firmware interface version 9.2.0
[   13.440161] i2400m_usb 1-8:1.0: WiMAX interface wmx0 (00:1d:e1:05:13:7d) ready
[   13.440377] usbcore: registered new interface driver i2400m_usb
[   13.449959] i2400m_usb 1-8:1.0: 'RF Control' (0x4602) command failed: -84 - invalid state (3)
[   13.606482] r8169: eth0: link down
[   13.606905] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   13.628820] iwlagn 0000:02:00.0: firmware: requesting iwlwifi-5150-2.ucode
[   13.766408] iwlagn 0000:02:00.0: loaded firmware version 8.24.2.2
...
[   67.547616] wlan0: Selected IBSS BSSID 02:2e:0e:ac:c4:77 based on configured SSID
[   78.257027] wlan0: no IPv6 routers present
[  395.114254] usb 1-1: USB disconnect, address 2
[  399.028122] usb 1-1: new high speed USB device using ehci_hcd and address 6
[  399.162694] usb 1-1: configuration #1 chosen from 1 choice
[  399.164996] scsi4 : SCSI emulation for USB Mass Storage devices
[  399.172418] usb-storage: device found at 6
[  399.172435] usb-storage: waiting for device to settle before scanning
[  404.172429] usb-storage: device scan complete
[  404.173598] scsi 4:0:0:0: Direct-Access     USB 2.0  Flash Disk       1100 PQ: 0 ANSI: 0 CCS
[  404.175746] sd 4:0:0:0: Attached scsi generic sg1 type 0
[  404.190123] sd 4:0:0:0: [sdb] 4062208 512-byte logical blocks: (2.07 GB/1.93 GiB)
[  404.194638] sd 4:0:0:0: [sdb] Write Protect is off
[  404.194651] sd 4:0:0:0: [sdb] Mode Sense: 43 00 00 00
[  404.194659] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[  404.201612] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[  404.201625]  sdb: sdb1
[  404.259574] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[  404.259602] sd 4:0:0:0: [sdb] Attached SCSI removable disk

Пользователь решил продолжить мысль 06 Января 2010, 00:50:26:вот кстати работало работало и перестало... и это даже без перезагрузки.
Пользователь решил продолжить мысль 06 Января 2010, 04:13:05:И снова заработало)) и еще одну особенность заметил:
при входе в линукс через консоль флешка преимущественно оседает в файле /dev/sdc1  а при входе с граф режимом гнома чаще оседает в файл  /dev/sdb1

[$oft]

опять сломано:

dmesg:

(Нажмите, чтобы показать/скрыть)

[    1.828040] Clocksource tsc unstable (delta = -130824596 ns)
[    1.895264] acpi device:1c: registered as cooling_device2
[    1.895579] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:1a/input/input6
[    1.895698] ACPI: Video Device [IGD] (multi-head: yes  rom: no  post: no)
[    1.908579] atkbd.c: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
[    1.908591] atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
[    1.912155] atkbd.c: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
[    1.912169] atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
[    1.960589] Linux agpgart interface v0.103
[    2.008982] agpgart-intel 0000:00:00.0: Intel 945GME Chipset
[    2.009381] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[    2.012366] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[    2.030654] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    2.030701] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    2.030766] r8169 0000:01:00.0: setting latency timer to 64
[    2.030831]   alloc irq_desc for 26 on node -1
[    2.030839]   alloc kstat_irqs on node -1
[    2.030867] r8169 0000:01:00.0: irq 26 for MSI/MSI-X
[    2.032711] eth0: RTL8102e at 0xf808c000, 00:24:21:6d:96:13, XID 34a00000 IRQ 26
[    2.083612] [drm] Initialized drm 1.1.0 20060810
[    2.086515] usb 1-5: configuration #1 chosen from 1 choice
[    2.115542] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    2.115554] i915 0000:00:02.0: setting latency timer to 64
[    2.222115] integrated sync not supported
[    2.236146] usb 1-6: new high speed USB device using ehci_hcd and address 4
[    2.344540] integrated sync not supported
[    2.349875] [drm] fb0: inteldrmfb frame buffer device
[    2.349892] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    2.381447] usb 1-6: configuration #1 chosen from 1 choice
[    2.405400] Initializing USB Mass Storage driver...
[    2.419559] scsi2 : SCSI emulation for USB Mass Storage devices
[    2.429117] usbcore: registered new interface driver usb-storage
[    2.429127] USB Mass Storage support registered.
[    2.429411] usb-storage: device found at 4
[    2.429415] usb-storage: waiting for device to settle before scanning
[    2.497048] usb 1-8: new high speed USB device using ehci_hcd and address 5
[    2.629955] usb 1-8: configuration #1 chosen from 1 choice
[    2.677492] [drm] LVDS-8: set mode 1024x600 e
[    2.880053] usb 3-1: new low speed USB device using uhci_hcd and address 2
[    3.057499] usb 3-1: configuration #1 chosen from 1 choice
[    3.079937] Console: switching to colour frame buffer device 128x37
[    3.090593] usbcore: registered new interface driver hiddev
[    3.104806] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input7
[    3.104983] generic-usb 0003:0458:003A.0001: input,hidraw0: USB HID v1.10 Mouse [Genius Optical Mouse] on usb-0000:00:1d.1-1/input0
[    3.105037] usbcore: registered new interface driver usbhid
[    3.105048] usbhid: v2.6:USB HID core driver
[    3.683650] PM: Starting manual resume from disk
[    3.683658] PM: Resume from partition 8:5
[    3.683663] PM: Checking hibernation image.
[    3.683979] PM: Resume from disk failed.
[    3.707218] EXT4-fs (sda3): barriers enabled
[    3.721005] kjournald2 starting: pid 362, dev sda3:8, commit interval 5 seconds
[    3.721073] EXT4-fs (sda3): delayed allocation enabled
[    3.721081] EXT4-fs: file extents enabled
[    3.724475] EXT4-fs: mballoc enabled
[    3.724506] EXT4-fs (sda3): mounted filesystem with ordered data mode
[    4.219133] type=1505 audit(1263320041.351:2): operation="profile_load" pid=385 name=/sbin/dhclient3
[    4.219715] type=1505 audit(1263320041.351:3): operation="profile_load" pid=385 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[    4.220079] type=1505 audit(1263320041.355:4): operation="profile_load" pid=385 name=/usr/lib/connman/scripts/dhclient-script
[    4.252081] type=1505 audit(1263320041.387:5): operation="profile_load" pid=386 name=/usr/bin/evince
[    4.260970] type=1505 audit(1263320041.395:6): operation="profile_load" pid=386 name=/usr/bin/evince-previewer
[    4.266461] type=1505 audit(1263320041.399:7): operation="profile_load" pid=386 name=/usr/bin/evince-thumbnailer
[    4.290399] type=1505 audit(1263320041.423:: operation="profile_load" pid=388 name=/usr/lib/cups/backend/cups-pdf
[    4.291125] type=1505 audit(1263320041.423:9): operation="profile_load" pid=388 name=/usr/sbin/cupsd
[    5.060762] Adding 1156640k swap on /dev/sda5.  Priority:-1 extents:1 across:1156640k
[    5.172399] EXT4-fs (sda3): internal journal on sda3:8
[    6.628708] udev: starting version 147
[    7.313465] Linux video capture interface: v2.00
[    7.387212] uvcvideo: Found UVC 1.00 device BisonCam, NB Pro (5986:0203)
[    7.391507] input: BisonCam, NB Pro as /devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/input/input8
[    7.391677] usbcore: registered new interface driver uvcvideo
[    7.391689] USB Video Class driver (v0.1.0)
[    7.429539] usb-storage: device scan complete
[    7.431819] scsi 2:0:0:0: Direct-Access     Generic- Multi-Card       1.00 PQ: 0 ANSI: 0 CCS
[    7.432944] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    7.444723] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[    7.601272] intel_rng: FWH not detected
[    7.649272] cfg80211: Calling CRDA to update world regulatory domain
[    7.687616] ehci_hcd 0000:00:1d.7: force halt; handhake f803a024 00004000 00000000 -> -110
[    7.689774] i2400m_usb 1-8:1.0: boot-mode cmd -1: error waiting for an ack: -110
[    7.689783] i2400m_usb 1-8:1.0: warm reset timed out, trying an ack
[    7.689801] i2400m_usb 1-8:1.0: boot-mode cmd 15: incomplete transfer (0 vs 16 submitted)
[    7.689810] i2400m_usb 1-8:1.0: device reboot ack: error -5 while waiting for reboot ack barker - rebooting
[    7.689822] i2400m_usb 1-8:1.0: E: barker error: -108
[    7.689830] i2400m_usb 1-8:1.0: warm reset failed (-108); trying USB reset
[    7.689850] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689858] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689866] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689874] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689883] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689890] hub 1-0:1.0: Cannot enable port 8.  Maybe the USB cable is bad?
[    7.689899] hub 1-0:1.0: cannot disable port 8 (err = -108)
[    7.689909] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689917] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689925] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689934] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689942] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689949] hub 1-0:1.0: Cannot enable port 8.  Maybe the USB cable is bad?
[    7.689958] hub 1-0:1.0: cannot disable port 8 (err = -108)
[    7.689967] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689975] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689983] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.689992] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.690000] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.690007] hub 1-0:1.0: Cannot enable port 8.  Maybe the USB cable is bad?
[    7.690015] hub 1-0:1.0: cannot disable port 8 (err = -108)
[    7.690025] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.690033] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.690041] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.690049] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.690058] hub 1-0:1.0: cannot reset port 8 (err = -108)
[    7.690064] hub 1-0:1.0: Cannot enable port 8.  Maybe the USB cable is bad?
[    7.690073] hub 1-0:1.0: cannot disable port 8 (err = -108)
[    7.690083] hub 1-0:1.0: cannot disable port 8 (err = -108)
[    7.690098] i2400m_usb 1-8:1.0: boot-mode cmd -1: error waiting for an ack: -19
[    7.690106] i2400m_usb 1-8:1.0: device reboot: error -19 while waiting for reboot barker - rebooting
[    7.690116] i2400m_usb 1-8:1.0: E: barker error: -19
[    7.690123] i2400m_usb 1-8:1.0: warm reset failed (-19); trying USB reset
[    7.690132] i2400m_usb 1-8:1.0: boot-mode cmd -1: error waiting for an ack: -19
[    7.690139] i2400m_usb 1-8:1.0: device reboot: error -19 while waiting for reboot barker - rebooting
[    7.690147] i2400m_usb 1-8:1.0: Timed out waiting for reboot ack
[    7.690154] i2400m_usb 1-8:1.0: read mac addr: bootrom init failed: -110
[    7.690167] i2400m_usb 1-8:1.0: cannot setup device: -110
[    7.690191] i2400m_usb: probe of 1-8:1.0 failed with error -110
[    7.690256] usbcore: registered new interface driver i2400m_usb
[    7.691064] hub 1-0:1.0: hub_port_status failed (err = -108)
[    7.838065] psmouse serio1: ID: 10 00 64
[    8.278192] lp: driver loaded but no devices found
[    8.409660] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27k
[    8.409670] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[    8.409818] iwlagn 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    8.409835] iwlagn 0000:02:00.0: setting latency timer to 64
[    8.409884] iwlagn 0000:02:00.0: Detected Intel Wireless WiFi Link 5150AGN REV=0x44
[    8.448379] iwlagn 0000:02:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
[    8.448456]   alloc irq_desc for 27 on node -1
[    8.448465]   alloc kstat_irqs on node -1
[    8.448496] iwlagn 0000:02:00.0: irq 27 for MSI/MSI-X
[    8.530075] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input9
[    8.547626] cfg80211: World regulatory domain updated:
[    8.547635]    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.547643]    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.547650]    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.547656]    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.547663]    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.547669]    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.044581] phy0: Selected rate control algorithm 'iwl-agn-rs'
[    9.125400] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125411] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125418] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125425] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125431] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125437] hub 1-0:1.0: Cannot enable port 6.  Maybe the USB cable is bad?
[    9.125444] hub 1-0:1.0: cannot disable port 6 (err = -108)
[    9.125452] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125458] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125465] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125471] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125477] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125483] hub 1-0:1.0: Cannot enable port 6.  Maybe the USB cable is bad?
[    9.125490] hub 1-0:1.0: cannot disable port 6 (err = -108)
[    9.125497] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125503] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125510] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125516] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125523] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125528] hub 1-0:1.0: Cannot enable port 6.  Maybe the USB cable is bad?
[    9.125535] hub 1-0:1.0: cannot disable port 6 (err = -108)
[    9.125542] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125549] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125555] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125561] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125568] hub 1-0:1.0: cannot reset port 6 (err = -108)
[    9.125573] hub 1-0:1.0: Cannot enable port 6.  Maybe the USB cable is bad?
[    9.125580] hub 1-0:1.0: cannot disable port 6 (err = -108)
[    9.125587] hub 1-0:1.0: cannot disable port 6 (err = -108)
[    9.125625] hub 1-0:1.0: hub_port_status failed (err = -108)
[    9.125637] hub 1-0:1.0: hub_port_status failed (err = -108)

НЕУЖЕЛИ НИКТО НЕ В КУРСЕ КАК ИСПРАВИТЬ???