вот полный вывод, не знаю почему в 1 раз неполный скопировал...
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.27-8-generic (buildd@rothera) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu11) ) #1 SMP Thu Nov 6 17:33:54 UTC 2008 (Ubuntu 2.6.27-8.17-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
[ 0.000000] BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] last_pfn = 0x1fff0 max_arch_pfn = 0x100000
[ 0.000000] kernel direct mapping tables up to 1fff0000 @ 7000-d000
[ 0.000000] RAMDISK: 1f810000 - 1ffdf964
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI: RSDP 000F7620, 0014 (r0 IntelR)
[ 0.000000] ACPI: RSDT 1FFF3000, 002C (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP 1FFF3040, 0074 (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT 1FFF30C0, 3EF5 (r1 INTELR AWRDACPI 1000 MSFT 100000D)
[ 0.000000] ACPI: FACS 1FFF0000, 0040
[ 0.000000] ACPI: APIC 1FFF6FC0, 0068 (r1 IntelR AWRDACPI 42302E31 AWRD 0)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 1fff0000
[ 0.000000] low ram: 00000000 - 1fff0000
[ 0.000000] bootmap 00002000 - 00006000
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 001fff0000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 00005c0a20] TEXT DATA BSS ==> [0000100000 - 00005c0a20]
[ 0.000000] #4 [001f810000 - 001ffdf964] RAMDISK ==> [001f810000 - 001ffdf964]
[ 0.000000] #5 [00005c1000 - 00005c4000] INIT_PG_TABLE ==> [00005c1000 - 00005c4000]
[ 0.000000] #6 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
[ 0.000000] #7 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000]
[ 0.000000] #8 [0000002000 - 0000006000] BOOTMAP ==> [0000002000 - 0000006000]
[ 0.000000] found SMP MP-table at [c00f5aa0] 000f5aa0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0001fff0
[ 0.000000] HighMem 0x0001fff0 -> 0x0001fff0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0001fff0
[ 0.000000] On node 0 totalpages: 130959
[ 0.000000] free_area_init_node: node 0, pgdat c048a500, node_mem_map c1000000
[ 0.000000] DMA zone: 3963 pages, LIFO batch:0
[ 0.000000] Normal zone: 125844 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
[ 0.000000] PERCPU: Allocating 41628 bytes of per cpu data
[ 0.000000] NR_CPUS: 64, nr_cpu_ids: 2, nr_node_ids 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129807
[ 0.000000] Kernel command line: root=UUID=44756a23-1a5d-48ad-993e-394061b9d906 ro quiet splash
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] TSC: PIT calibration confirmed by PMTIMER.
[ 0.000000] TSC: using PMTIMER calibration value
[ 0.000000] Detected 1817.886 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Memory: 505668k/524224k available (2572k kernel code, 18016k reserved, 1160k data, 424k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xffc77000 - 0xfffff000 (3616 kB)
[ 0.004000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.004000] vmalloc : 0xe0800000 - 0xff3fe000 ( 491 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
[ 0.004000] .init : 0xc04ab000 - 0xc0515000 ( 424 kB)
[ 0.004000] .data : 0xc03832da - 0xc04a5680 (1160 kB)
[ 0.004000] .text : 0xc0100000 - 0xc03832da (2572 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.004000] SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.004019] Calibrating delay loop (skipped), value calculated using timer frequency.. 3635.77 BogoMIPS (lpj=7271544)
[ 0.004060] Security Framework initialized
[ 0.004072] SELinux: Disabled at boot.
[ 0.004112] AppArmor: AppArmor initialized
[ 0.004135] Mount-cache hash table entries: 512
[ 0.004521] Initializing cgroup subsys ns
[ 0.004536] Initializing cgroup subsys cpuacct
[ 0.004542] Initializing cgroup subsys memory
[ 0.004579] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.004587] CPU: L2 cache: 128K
[ 0.004592] CPU: Hyper-Threading is disabled
[ 0.004621] Checking 'hlt' instruction... OK.
[ 0.020796] SMP alternatives: switching to UP code
[ 0.032025] ACPI: Core revision 20080609
[ 0.034844] ACPI: Checking initramfs for custom DSDT
[ 0.592293] ENABLING IO-APIC IRQs
[ 0.592497] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.632350] CPU0: Intel(R) Celeron(R) CPU 1.80GHz stepping 03
[ 0.636031] Brought up 1 CPUs
[ 0.636031] Total of 1 processors activated (3635.77 BogoMIPS).
[ 0.636031] CPU0 attaching sched-domain:
[ 0.636031] domain 0: span 0 level CPU
[ 0.636031] groups: 0
[ 0.636031] net_namespace: 840 bytes
[ 0.636031] Booting paravirtualized kernel on bare hardware
[ 0.636031] Time: 11:28:42 Date: 11/24/08
[ 0.636031] NET: Registered protocol family 16
[ 0.636031] EISA bus registered
[ 0.636031] ACPI: bus type pci registered
[ 0.663457] PCI: PCI BIOS revision 2.10 entry at 0xfb380, last bus=2
[ 0.663464] PCI: Using configuration type 1 for base access
[ 0.668962] ACPI: EC: Look up EC in DSDT
[ 0.679212] ACPI: Interpreter enabled
[ 0.679223] ACPI: (supports S0 S1 S4 S5)
[ 0.679257] ACPI: Using IOAPIC for interrupt routing
[ 0.695658] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.695918] PCI: 0000:00:00.0 reg 10 32bit mmio: [d0000000, d7ffffff]
[ 0.696103] PCI: 0000:00:1d.0 reg 20 io port: [d800, d81f]
[ 0.696173] PCI: 0000:00:1d.1 reg 20 io port: [d000, d01f]
[ 0.696240] PCI: 0000:00:1d.2 reg 20 io port: [d400, d41f]
[ 0.696309] PCI: 0000:00:1d.7 reg 10 32bit mmio: [e2100000, e21003ff]
[ 0.696372] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.696379] pci 0000:00:1d.7: PME# disabled
[ 0.696430] * The chipset may have PM-Timer Bug. Due to workarounds for a bug,
[ 0.696433] * this clock source is slow. If you are sure your timer does not have
[ 0.696435] * this bug, please use "acpi_pm_good" to disable the workaround
[ 0.696488] HPET not enabled in BIOS. You might try hpet=force boot option
[ 0.696499] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
[ 0.696505] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH4 GPIO
[ 0.696532] PCI: 0000:00:1f.1 reg 10 io port: [0, 7]
[ 0.696542] PCI: 0000:00:1f.1 reg 14 io port: [0, 3]
[ 0.696551] PCI: 0000:00:1f.1 reg 18 io port: [0, 7]
[ 0.696561] PCI: 0000:00:1f.1 reg 1c io port: [0, 3]
[ 0.696570] PCI: 0000:00:1f.1 reg 20 io port: [f000, f00f]
[ 0.696580] PCI: 0000:00:1f.1 reg 24 32bit mmio: [0, 3ff]
[ 0.696643] PCI: 0000:00:1f.3 reg 20 io port: [500, 51f]
[ 0.696698] PCI: 0000:00:1f.5 reg 10 io port: [e000, e0ff]
[ 0.696708] PCI: 0000:00:1f.5 reg 14 io port: [e400, e43f]
[ 0.696717] PCI: 0000:00:1f.5 reg 18 32bit mmio: [e2101000, e21011ff]
[ 0.696727] PCI: 0000:00:1f.5 reg 1c 32bit mmio: [e2102000, e21020ff]
[ 0.696762] pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
[ 0.696769] pci 0000:00:1f.5: PME# disabled
[ 0.696816] PCI: 0000:01:00.0 reg 10 32bit mmio: [e0000000, e0ffffff]
[ 0.696826] PCI: 0000:01:00.0 reg 14 32bit mmio: [d8000000, dfffffff]
[ 0.696852] PCI: 0000:01:00.0 reg 30 32bit mmio: [0, 1ffff]
[ 0.696915] PCI: bridge 0000:00:01.0 32bit mmio: [e0000000, e1ffffff]
[ 0.696921] PCI: bridge 0000:00:01.0 32bit mmio pref: [d8000000, dfffffff]
[ 0.696965] PCI: 0000:02:00.0 reg 10 32bit mmio: [e2000000, e200ffff]
[ 0.696975] PCI: 0000:02:00.0 reg 14 io port: [c000, c007]
[ 0.697020] pci 0000:02:00.0: PME# supported from D3hot D3cold
[ 0.697027] pci 0000:02:00.0: PME# disabled
[ 0.697081] PCI: 0000:02:05.0 reg 10 io port: [c400, c4ff]
[ 0.697093] PCI: 0000:02:05.0 reg 14 32bit mmio: [e2010000, e20100ff]
[ 0.697142] pci 0000:02:05.0: supports D1
[ 0.697145] pci 0000:02:05.0: supports D2
[ 0.697149] pci 0000:02:05.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.697156] pci 0000:02:05.0: PME# disabled
[ 0.697198] pci 0000:00:1e.0: transparent bridge
[ 0.697204] PCI: bridge 0000:00:1e.0 io port: [c000, cfff]
[ 0.697211] PCI: bridge 0000:00:1e.0 32bit mmio: [e2000000, e20fffff]
[ 0.697232] bus 00 -> node 0
[ 0.697260] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.697760] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.737410] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 0.737688] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 0.737956] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.738222] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 0.738490] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.738760] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.739027] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.739295] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[ 0.739900] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.740140] pnp: PnP ACPI init
[ 0.740168] ACPI: bus type pnp registered
[ 0.750473] pnp: PnP ACPI: found 14 devices
[ 0.750482] ACPI: ACPI bus type pnp unregistered
[ 0.750490] PnPBIOS: Disabled by ACPI PNP
[ 0.752289] PCI: Using ACPI for IRQ routing
[ 0.752625] NET: Registered protocol family 8
[ 0.752625] NET: Registered protocol family 20
[ 0.752625] NetLabel: Initializing
[ 0.752625] NetLabel: domain hash size = 128
[ 0.752625] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.752625] NetLabel: unlabeled traffic allowed by default
[ 0.753272] tracer: 772 pages allocated for 65536 entries of 48 bytes
[ 0.753278] actual entries 65620
[ 0.753616] AppArmor: AppArmor Filesystem Enabled
[ 0.753654] ACPI: RTC can wake from S4
[ 0.753715] system 00:01: ioport range 0x400-0x4bf could not be reserved
[ 0.753715] system 00:02: ioport range 0xb78-0xb7b has been reserved
[ 0.753715] system 00:02: ioport range 0xf78-0xf7b has been reserved
[ 0.753715] system 00:02: ioport range 0xa78-0xa7b has been reserved
[ 0.753715] system 00:02: ioport range 0xe78-0xe7b has been reserved
[ 0.753715] system 00:02: ioport range 0xbbc-0xbbf has been reserved
[ 0.753715] system 00:02: ioport range 0xfbc-0xfbf has been reserved
[ 0.753715] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.753715] system 00:02: ioport range 0x294-0x297 has been reserved
[ 0.753715] system 00:02: ioport range 0x4e0-0x4e7 has been reserved
[ 0.791715] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.791721] pci 0000:00:01.0: IO window: disabled
[ 0.791730] pci 0000:00:01.0: MEM window: 0xe0000000-0xe1ffffff
[ 0.791737] pci 0000:00:01.0: PREFETCH window: 0x000000d8000000-0x000000dfffffff
[ 0.791747] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[ 0.791753] pci 0000:00:1e.0: IO window: 0xc000-0xcfff
[ 0.791761] pci 0000:00:1e.0: MEM window: 0xe2000000-0xe20fffff
[ 0.791768] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.791795] pci 0000:00:1e.0: setting latency timer to 64
[ 0.791802] bus: 00 index 0 io port: [0, ffff]
[ 0.791806] bus: 00 index 1 mmio: [0, ffffffff]
[ 0.791810] bus: 01 index 0 mmio: [0, 0]
[ 0.791813] bus: 01 index 1 mmio: [e0000000, e1ffffff]
[ 0.791817] bus: 01 index 2 mmio: [d8000000, dfffffff]
[ 0.791820] bus: 01 index 3 mmio: [0, 0]
[ 0.791824] bus: 02 index 0 io port: [c000, cfff]
[ 0.791828] bus: 02 index 1 mmio: [e2000000, e20fffff]
[ 0.791832] bus: 02 index 2 mmio: [0, 0]
[ 0.791836] bus: 02 index 3 io port: [0, ffff]
[ 0.791839] bus: 02 index 4 mmio: [0, ffffffff]
[ 0.791865] NET: Registered protocol family 2
[ 0.792205] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.792678] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.792802] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.793020] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.793028] TCP reno registered
[ 0.793325] NET: Registered protocol family 1
[ 0.793564] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
[ 1.340872] it is
[ 1.985402] Freeing initrd memory: 7998k freed
[ 1.987955] audit: initializing netlink socket (disabled)
[ 1.987992] type=2000 audit(1227526122.984:1): initialized
[ 1.995262] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 2.004414] VFS: Disk quotas dquot_6.5.1
[ 2.004745] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.005130] msgmni has been set to 1003
[ 2.005570] io scheduler noop registered
[ 2.005577] io scheduler anticipatory registered
[ 2.005581] io scheduler deadline registered
[ 2.005626] io scheduler cfq registered (default)
[ 2.005752] pci 0000:01:00.0: Boot video device
[ 2.007173] isapnp: Scanning for PnP cards...
[ 2.361131] isapnp: No Plug & Play device found
[ 2.604918] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 2.605236] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.605847] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.608605] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.609901] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.618412] brd: module loaded
[ 2.618673] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 2.619162] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.621779] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.621802] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.623531] mice: PS/2 mouse device common for all mice
[ 2.624298] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 2.624345] rtc0: alarms up to one month
[ 2.624942] EISA: Probing bus 0 at eisa.0
[ 2.624991] EISA: Detected 0 cards.
[ 2.624997] cpuidle: using governor ladder
[ 2.625001] cpuidle: using governor menu
[ 2.626120] TCP cubic registered
[ 2.626208] Using IPI No-Shortcut mode
[ 2.627562] registered taskstats version 1
[ 2.627802] Magic number: 0:925:479
[ 2.628041] rtc_cmos 00:04: setting system clock to 2008-11-24 11:28:44 UTC (1227526124)
[ 2.628049] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.628052] EDD information not available.
[ 2.628681] Freeing unused kernel memory: 424k freed
[ 2.628789] Write protecting the kernel text: 2576k
[ 2.628845] Write protecting the kernel read-only data: 936k
[ 2.647872] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 3.002267] fuse init (API version 7.9)
[ 3.250732] fan PNP0C0B:00: registered as cooling_device0
[ 3.250754] ACPI: Fan [FAN] (on)
[ 3.324656] processor ACPI0007:00: registered as cooling_device1
[ 3.363342] thermal LNXTHERM:01: registered as thermal_zone0
[ 3.394025] ACPI: Thermal Zone [THRM] (45 C)
[ 4.819316] usbcore: registered new interface driver usbfs
[ 4.819371] usbcore: registered new interface driver hub
[ 4.819537] usbcore: registered new device driver usb
[ 4.847743] No dock devices found.
[ 4.858558] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 4.858583] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 4.858590] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 4.858726] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 4.862652] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[ 4.862681] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe2100000
[ 4.884108] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 4.884476] usb usb1: configuration #1 chosen from 1 choice
[ 4.884547] hub 1-0:1.0: USB hub found
[ 4.884575] hub 1-0:1.0: 6 ports detected
[ 4.884751] USB Universal Host Controller Interface driver v3.0
[ 5.035292] SCSI subsystem initialized
[ 5.047337] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 5.047348] via-rhine: Broken BIOS detected, avoid_D3 enabled.
[ 5.092841] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.092861] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 5.092868] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 5.092950] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 5.093001] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000d800
[ 5.093404] usb usb2: configuration #1 chosen from 1 choice
[ 5.093480] hub 2-0:1.0: USB hub found
[ 5.093505] hub 2-0:1.0: 2 ports detected
[ 5.115940] libata version 3.00 loaded.
[ 5.300793] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 5.300812] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 5.300819] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 5.300901] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 5.300953] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d000
[ 5.301348] usb usb3: configuration #1 chosen from 1 choice
[ 5.301423] hub 3-0:1.0: USB hub found
[ 5.301448] hub 3-0:1.0: 2 ports detected
[ 5.404789] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 5.404811] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 5.404818] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 5.404903] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 5.404958] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d400
[ 5.405351] usb usb4: configuration #1 chosen from 1 choice
[ 5.405430] hub 4-0:1.0: USB hub found
[ 5.405456] hub 4-0:1.0: 2 ports detected
[ 5.412090] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 5.509697] via-rhine 0000:02:05.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 5.518272] eth0: VIA Rhine III at 0xe2010000, 00:04:61:63:a6:da, IRQ 22.
[ 5.518981] eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
[ 5.528538] pata_acpi 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 5.528632] pata_acpi 0000:00:1f.1: setting latency timer to 64
[ 5.528662] pata_acpi 0000:00:1f.1: PCI INT A disabled
[ 5.545798] ata_piix 0000:00:1f.1: version 2.12
[ 5.545826] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 5.545912] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 5.548289] scsi0 : ata_piix
[ 5.548583] scsi1 : ata_piix
[ 5.550035] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 5.550043] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 5.610354] usb 2-2: configuration #1 chosen from 1 choice
[ 6.075431] ata2.00: ATA-7: WDC WD2500JB-00REA0, 20.00K20, max UDMA/100
[ 6.075439] ata2.00: 488397168 sectors, multi 0: LBA48
[ 6.075478] ata2.01: ATAPI: LITE-ON DVDRW LH-16W1P, SL05, max UDMA/66
[ 6.075500] ata2.00: limited to UDMA/33 due to 40-wire cable
[ 6.075505] ata2.01: limited to UDMA/33 due to 40-wire cable
[ 6.080566] ata2.00: configured for UDMA/33
[ 6.112357] ata2.01: configured for UDMA/33
[ 6.112660] scsi 1:0:0:0: Direct-Access ATA WDC WD2500JB-00R 20.0 PQ: 0 ANSI: 5
[ 6.114125] scsi 1:0:1:0: CD-ROM LITE-ON DVDRW LH-16W1P SL05 PQ: 0 ANSI: 5
[ 6.801816] scsi 1:0:0:0: Attached scsi generic sg0 type 0
[ 6.802063] scsi 1:0:1:0: Attached scsi generic sg1 type 5
[ 6.904921] Driver 'sd' needs updating - please use bus_type methods
[ 6.906087] sd 1:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[ 6.906172] sd 1:0:0:0: [sda] Write Protect is off
[ 6.906179] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.906315] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.906579] sd 1:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
[ 6.906660] sd 1:0:0:0: [sda] Write Protect is off
[ 6.906668] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 6.906806] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.906821] sda: sda1 sda2 < sda5<4>Driver 'sr' needs updating - please use bus_type methods
[ 6.945614] sda6 sda7 >
[ 6.952996] sd 1:0:0:0: [sda] Attached SCSI disk
[ 6.967774] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 6.967784] Uniform CD-ROM driver Revision: 3.20
[ 6.967998] sr 1:0:1:0: Attached scsi CD-ROM sr0
[ 7.429743] PM: Starting manual resume from disk
[ 7.429758] PM: Resume from partition 8:7
[ 7.429761] PM: Checking hibernation image.
[ 7.430140] PM: Resume from disk failed.
[ 7.535083] kjournald starting. Commit interval 5 seconds
[ 7.535121] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.617323] udevd version 124 started
[ 14.922778] Linux agpgart interface v0.103
[ 14.996442] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 15.075712] agpgart-intel 0000:00:00.0: Intel 845G Chipset
[ 15.085094] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xd0000000
[ 15.147859] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 15.212832] iTCO_vendor_support: vendor-support=0
[ 15.268682] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 15.269866] iTCO_wdt: Found a ICH4 TCO device (Version=1, TCOBASE=0x0460)
[ 15.270253] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 15.447502] intel_rng: FWH not detected
[ 15.583159] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 15.592095] ACPI: Power Button (FF) [PWRF]
[ 15.592367] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[ 15.608071] ACPI: Power Button (CM) [PWRB]
[ 15.892976] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 16.998559] nvidia: module license 'NVIDIA' taints kernel.
[ 17.688523] parport_pc 00:0a: reported by Plug and Play ACPI
[ 17.688590] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 19.538997] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 19.539753] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.09 Mon Oct 27 14:23:30 PST 2008
[ 19.610750] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input5
[ 19.652143] usb 2-2: reset full speed USB device using uhci_hcd and address 2
[ 19.711743] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 19.711786] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 19.852164] firmware: requesting speedtch-1.bin.0.00
[ 19.852439] usbcore: registered new interface driver speedtch
[ 20.032080] intel8x0_measure_ac97_clock: measured 54393 usecs
[ 20.032087] intel8x0: clocking to 48000
[ 23.356756] firmware: requesting speedtch-1.bin.0
[ 23.460854] speedtch 2-2:1.0: found stage 1 firmware speedtch-1.bin.0
[ 23.460864] firmware: requesting speedtch-2.bin.0.00
[ 23.467480] firmware: requesting speedtch-2.bin.0
[ 23.939087] speedtch 2-2:1.0: found stage 2 firmware speedtch-2.bin.0
[ 24.942230] lp0: using parport0 (interrupt-driven).
[ 25.266838] Adding 497972k swap on /dev/sda7. Priority:-1 extents:1 across:497972k
[ 25.904247] EXT3 FS on sda6, internal journal
[ 27.450209] type=1505 audit(1227508149.075:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=3911
[ 27.784439] type=1505 audit(1227508149.411:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=3916
[ 27.785042] type=1505 audit(1227508149.411:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=3916
[ 28.007796] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 28.630340] ATM dev 0: ADSL line is synchronising
[ 29.014029] ACPI: WMI: Mapper loaded
[ 31.089931] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 31.224629] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 31.224652] apm: overridden by ACPI.
[ 31.468256] ppdev: user-space parallel port driver
[ 34.280207] Bluetooth: Core ver 2.13
[ 34.284977] NET: Registered protocol family 31
[ 34.284997] Bluetooth: HCI device and connection manager initialized
[ 34.285005] Bluetooth: HCI socket layer initialized
[ 34.321415] Bluetooth: L2CAP ver 2.11
[ 34.321435] Bluetooth: L2CAP socket layer initialized
[ 34.371073] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 34.371094] Bluetooth: BNEP filters: protocol multicast
[ 34.419665] Bridge firewalling registered
[ 34.434581] pan0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[ 34.449373] Bluetooth: RFCOMM socket layer initialized
[ 34.459560] Bluetooth: RFCOMM TTY layer initialized
[ 34.459584] Bluetooth: RFCOMM ver 1.10
[ 34.475598] Bluetooth: SCO (Voice Link) ver 0.6
[ 34.475622] Bluetooth: SCO socket layer initialized
[ 37.400487] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
[ 37.400540] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
[ 37.400585] nvidia 0000:01:00.0: putting AGP V2 device into 4x mode
[ 38.681749] eth0: link down
[ 42.608061] ATM dev 0: DSL line goes up
[ 42.614087] ATM dev 0: ADSL line is up (288 kb/s down | 160 kb/s up)
[ 51.154417] PPP generic driver version 2.4.2
[ 51.195423] NET: Registered protocol family 17
[ 51.280360] NET: Registered protocol family 10
[ 51.284592] lo: Disabled Privacy Extensions
[ 51.287879] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 51.425610] NET: Registered protocol family 24
[ 62.228015] nas0: no IPv6 routers present
[ 168.612612] ppdev0: registered pardevice
[ 168.654570] ppdev0: unregistered pardevice
[ 169.871475] ppdev0: registered pardevice
[ 169.912826] ppdev0: unregistered pardevice
[ 171.244228] ppdev0: registered pardevice
[ 171.296061] ppdev0: unregistered pardevice
Тема: Проблема с USB на мониторе HP w2207h (Прочитано 3981 раз)
