Здравствуйте.
Использую мышь Майкрософт скульпт эргономик на Ubuntu 20.10. Адаптер мыши подключен к ноутбуку постоянно. Если ноутбук уснёт, то после выхода из спящего режима у мыши не работает скролл. Временное решение это вытащить адаптер и снова вставить, тогда скролл мыши работает нормально.
Подскажите пожалуйста куда копать?
Lsusb
lsusb
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 0c45:6366 Microdia Webcam Vitade AF
Bus 001 Device 012: ID 045e:07a5 Microsoft Corp. Wireless Receiver 1461C
Bus 001 Device 002: ID 8087:0a2a Intel Corp. Bluetooth wireless interface
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Кусок из dmesq. Если правильно понял то как раз про спящий режим.
ACPI: EC: interrupt blocked
[11866.644324] ACPI: Preparing to enter system sleep state S3
[11866.646411] ACPI: EC: event blocked
[11866.646413] ACPI: EC: EC stopped
[11866.646415] PM: Saving platform NVS memory
[11866.646428] Disabling non-boot CPUs ...
[11866.647493] IRQ 123: no longer affine to CPU1
[11866.648549] smpboot: CPU 1 is now offline
[11866.655205] IRQ 121: no longer affine to CPU2
[11866.656260] smpboot: CPU 2 is now offline
[11866.662559] IRQ 126: no longer affine to CPU3
[11866.663625] smpboot: CPU 3 is now offline
[11866.673017] ACPI: Low-level resume complete
[11866.673151] ACPI: EC: EC started
[11866.673153] PM: Restoring platform NVS memory
[11866.678131] Enabling non-boot CPUs ...
[11866.678256] x86: Booting SMP configuration:
[11866.678258] smpboot: Booting Node 0 Processor 1 APIC 0x2
[11866.680501] CPU1 is up
[11866.680578] smpboot: Booting Node 0 Processor 2 APIC 0x4
[11866.682867] CPU2 is up
[11866.682952] smpboot: Booting Node 0 Processor 3 APIC 0x6
[11866.685214] CPU3 is up
[11866.685637] ACPI: Waking up from system sleep state S3
[11866.694607] acpi LNXPOWER:17: Turning ON
[11866.840254] ACPI: EC: interrupt unblocked
[11866.865901] ACPI: EC: event unblocked
[11866.876219] sd 1:0:0:0: [sda] Starting disk
[11867.155104] usb 1-7: reset high-speed USB device number 4 using xhci_hcd
[11867.192006] ata1: SATA link down (SStatus 4 SControl 300)
[11867.355094] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[11867.368360] ata2.00: configured for UDMA/133
[11867.431411] usb 1-6: reset high-speed USB device number 10 using xhci_hcd
[11867.875456] usb 1-6.1: reset full-speed USB device number 11 using xhci_hcd
[11867.992916] acpi LNXPOWER:19: Turning OFF
[11867.993490] acpi LNXPOWER:18: Turning OFF
[11867.994012] mei_hdcp 0000:00:0f.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_component_ops [i915])
[11867.994210] acpi LNXPOWER:16: Turning OFF
[11867.994758] acpi LNXPOWER:14: Turning OFF
[11867.995253] acpi LNXPOWER:12: Turning OFF
[11867.995796] acpi LNXPOWER:10: Turning OFF
[11867.996350] acpi LNXPOWER:0e: Turning OFF
[11867.996712] acpi LNXPOWER:0a: Turning OFF
[11867.996978] OOM killer enabled.
[11867.996979] Restarting tasks ... done.
[11868.019842] thermal thermal_zone4: failed to read out thermal zone (-61)
[11868.052402] PM: suspend exit
[11868.188310] iwlwifi 0000:01:00.0: Applying debug destination EXTERNAL_DRAM
[11868.275622] iwlwifi 0000:01:00.0: Applying debug destination EXTERNAL_DRAM
[11868.277671] iwlwifi 0000:01:00.0: FW already configured (0) - re-configuring
[11872.811609] wlp1s0: authenticate with 50:ff:20:10:66:c0
[11872.816953] wlp1s0: send auth to 50:ff:20:10:66:c0 (try 1/3)
[11872.820894] wlp1s0: authenticated
[11872.823144] wlp1s0: associate with 50:ff:20:10:66:c0 (try 1/3)
[11872.824215] wlp1s0: RX AssocResp from 50:ff:20:10:66:c0 (capab=0xc11 status=0 aid=4)
[11872.825992] wlp1s0: associated
[11872.938636] IPv6: ADDRCONF(NETDEV_CHANGE): wlp1s0: link becomes ready
[12603.544423] usb 1-6: USB disconnect, device number 10
[12603.544429] usb 1-6.1: USB disconnect, device number 11
[12605.946254] usb 1-6: new full-speed USB device number 12 using xhci_hcd
[12606.103694] usb 1-6: New USB device found, idVendor=045e, idProduct=07a5, bcdDevice= 7.97
[12606.103700] usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[12606.103703] usb 1-6: Product: Microsoft® 2.4GHz Transceiver v9.0
[12606.103705] usb 1-6: Manufacturer: Microsoft
[12606.108175] input: Microsoft Microsoft® 2.4GHz Transceiver v9.0 as /devices/pci0000:00/0000:00:15.0/usb1/1-6/1-6:1.0/0003:045E:07A5.000E/input/input38
[12606.167158] hid-generic 0003:045E:07A5.000E: input,hidraw1: USB HID v1.11 Keyboard [Microsoft Microsoft® 2.4GHz Transceiver v9.0] on usb-0000:00:15.0-6/input0
[12606.173734] input: Microsoft Microsoft® 2.4GHz Transceiver v9.0 Mouse as /devices/pci0000:00/0000:00:15.0/usb1/1-6/1-6:1.1/0003:045E:07A5.000F/input/input39
[12606.173960] input: Microsoft Microsoft® 2.4GHz Transceiver v9.0 Consumer Control as /devices/pci0000:00/0000:00:15.0/usb1/1-6/1-6:1.1/0003:045E:07A5.000F/input/input40
[12606.174091] hid-generic 0003:045E:07A5.000F: input,hidraw2: USB HID v1.11 Mouse [Microsoft Microsoft® 2.4GHz Transceiver v9.0] on usb-0000:00:15.0-6/input1
[12606.179911] input: Microsoft Microsoft® 2.4GHz Transceiver v9.0 Consumer Control as /devices/pci0000:00/0000:00:15.0/usb1/1-6/1-6:1.2/0003:045E:07A5.0010/input/input41
[12606.238606] input: Microsoft Microsoft® 2.4GHz Transceiver v9.0 System Control as /devices/pci0000:00/0000:00:15.0/usb1/1-6/1-6:1.2/0003:045E:07A5.0010/input/input42
[12606.238797] hid-generic 0003:045E:07A5.0010: input,hidraw3: USB HID v1.11 Device [Microsoft Microsoft® 2.4GHz Transceiver v9.0] on usb-0000:00:15.0-6/input2