hp 1320 по сети

[MikhalevDM]

Добрый день!
Помогите пожалуйста.
Принтер HP 1320 подключен к Windows 7.
Мой компютер с linux mint 17.3
С помощью "принтеры-localhost" нахожу и добавляю этот принтер. Печатаю пробную страницу и выдается сообщение. "Страница отправлена на печать" с принтером ничего не происходит. Через минут 5-10 на экране информационное сообщени " Страница напечатана". Но по факту страница не печатается.
Ранее этот принтер был без проблем подключен и работал. Затем что то пошло не так. Не долго думаю переустановил систему. Без результатов.

[MAKAP]

Так пробовал?

(Нажмите, чтобы показать/скрыть)

sudo apt-get install hplip
sudo hp-setup

[MikhalevDM]

MAKAP, Спасибо.
Попробывал. выдает ошибку
"HPLIP cannot detect printers in your network.
This may be due to existing firewall settings blocking the required ports. When you are in a trusted network environment, you may open the ports for network services like mdns and slp in the firewall. For detailed steps follow the link. http://hplipopensource.com/node/375"


Пользователь добавил сообщение 01 Июня 2016, 15:32:34:Вот лог принтера из терминала

(Нажмите, чтобы показать/скрыть)

E [01/Jun/2016:09:21:57 +0300] [Job 16] Can't load /etc/samba/smb.conf - run testparm to debug it
E [01/Jun/2016:09:27:07 +0300] [Job 16] Stopping unresponsive job.
E [01/Jun/2016:09:27:17 +0300] [Job 16] Can't load /etc/samba/smb.conf - run testparm to debug it
E [01/Jun/2016:09:32:27 +0300] [Job 16] Stopping unresponsive job.
E [01/Jun/2016:09:32:38 +0300] [Job 16] Can't load /etc/samba/smb.conf - run testparm to debug it
E [01/Jun/2016:09:37:48 +0300] [Job 16] Stopping unresponsive job.
E [01/Jun/2016:09:38:00 +0300] [Job 16] Can't load /etc/samba/smb.conf - run testparm to debug it
E [01/Jun/2016:09:43:09 +0300] [Job 16] Stopping unresponsive job.
E [01/Jun/2016:09:43:19 +0300] [Job 16] Can't load /etc/samba/smb.conf - run testparm to debug it
E [01/Jun/2016:09:48:28 +0300] [Job 16] Stopping unresponsive job.
E [01/Jun/2016:09:48:38 +0300] [Job 16] Can't load /etc/samba/smb.conf - run testparm to debug it
E [01/Jun/2016:09:48:48 +0300] [Job 16] Job aborted after 5 unsuccessful attempts.
D [01/Jun/2016:09:48:48 +0300] [Job 16] The following messages were recorded from 09:48:38 to 09:48:48
D [01/Jun/2016:09:48:48 +0300] [Job 16] Job submission timed out.
D [01/Jun/2016:09:48:48 +0300] [Job 16] time-at-processing=1464763718
D [01/Jun/2016:09:48:48 +0300] [Job 16] 4 filters for job:
D [01/Jun/2016:09:48:48 +0300] [Job 16] bannertopdf (application/vnd.cups-pdf-banner to application/pdf, cost 32)
D [01/Jun/2016:09:48:48 +0300] [Job 16] pdftopdf (application/pdf to application/vnd.cups-pdf, cost 66)
D [01/Jun/2016:09:48:48 +0300] [Job 16] gstoraster (application/vnd.cups-pdf to application/vnd.cups-raster, cost 99)
D [01/Jun/2016:09:48:48 +0300] [Job 16] hpcups (application/vnd.cups-raster to printer/HP-LaserJet-1320, cost 0)
D [01/Jun/2016:09:48:48 +0300] [Job 16] job-sheets=none,none
D [01/Jun/2016:09:48:48 +0300] [Job 16] argv[0]="HP-LaserJet-1320"
D [01/Jun/2016:09:48:48 +0300] [Job 16] argv[1]="16"
D [01/Jun/2016:09:48:48 +0300] [Job 16] argv[2]="mikhalev"
D [01/Jun/2016:09:48:48 +0300] [Job 16] argv[3]="Test Page"
D [01/Jun/2016:09:48:48 +0300] [Job 16] argv[4]="1"
D [01/Jun/2016:09:48:48 +0300] [Job 16] argv[5]="job-uuid=urn:uuid:b3dce039-37e5-32ce-7879-4bcf8cbbbd3b job-originating-host-name=localhost time-at-creation=1464705574 time-at-processing=1464763718"
D [01/Jun/2016:09:48:48 +0300] [Job 16] argv[6]="/var/spool/cups/d00016-001"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[0]="CUPS_CACHEDIR=/var/cache/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[1]="CUPS_DATADIR=/usr/share/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[2]="CUPS_DOCROOT=/usr/share/cups/doc-root"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[3]="CUPS_FONTPATH=/usr/share/cups/fonts"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[4]="CUPS_REQUESTROOT=/var/spool/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[5]="CUPS_SERVERBIN=/usr/lib/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[6]="CUPS_SERVERROOT=/etc/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[7]="CUPS_STATEDIR=/var/run/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[8]="HOME=/var/spool/cups/tmp"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[9]="PATH=/usr/lib/cups/filter:/usr/bin:/usr/sbin:/bin:/usr/bin"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[10]="SERVER_ADMIN=root@mikhalev-HP-Compaq-dc7900-Small-Form-Factor"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[11]="SOFTWARE=CUPS/1.7.2"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[12]="TMPDIR=/var/spool/cups/tmp"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[13]="USER=root"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[14]="CUPS_MAX_MESSAGE=2047"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[15]="CUPS_SERVER=/var/run/cups/cups.sock"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[16]="CUPS_ENCRYPTION=IfRequested"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[17]="IPP_PORT=631"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[18]="CHARSET=utf-8"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[19]="LANG=ru_RU.UTF-8"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[20]="PPD=/etc/cups/ppd/HP-LaserJet-1320.ppd"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[21]="RIP_MAX_CACHE=128m"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[22]="CONTENT_TYPE=application/vnd.cups-pdf-banner"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[23]="DEVICE_URI=smb://WORKGROUP/USER-KLO4EK/hp%20LaserJet%201320%20PCL%205"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[24]="PRINTER_INFO=HP LaserJet 1320"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[25]="PRINTER_LOCATION="
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[26]="PRINTER=HP-LaserJet-1320"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[27]="PRINTER_STATE_REASONS=none"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[28]="CUPS_FILETYPE=document"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[29]="FINAL_CONTENT_TYPE=printer/HP-LaserJet-1320"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[30]="AUTH_I****"
D [01/Jun/2016:09:48:48 +0300] [Job 16] Started filter /usr/lib/cups/filter/bannertopdf (PID 4402)
D [01/Jun/2016:09:48:48 +0300] [Job 16] Started filter /usr/lib/cups/filter/pdftopdf (PID 4403)
D [01/Jun/2016:09:48:48 +0300] [Job 16] Started filter /usr/lib/cups/filter/gstoraster (PID 4404)
D [01/Jun/2016:09:48:48 +0300] [Job 16] Started filter /usr/lib/cups/filter/hpcups (PID 4405)
D [01/Jun/2016:09:48:48 +0300] [Job 16] Started backend /usr/lib/cups/backend/smb (PID 4406)
D [01/Jun/2016:09:48:48 +0300] [Job 16] Set job-printer-state-message to "Can't load /etc/samba/smb.conf - run testparm to debug it", current level=ERROR
D [01/Jun/2016:09:48:48 +0300] [Job 16] PID 4406 (/usr/lib/cups/backend/smb) stopped with status 1.
D [01/Jun/2016:09:48:48 +0300] [Job 16] Hint: Try setting the LogLevel to "debug" to find out more.
D [01/Jun/2016:09:48:48 +0300] [Job 16] PDF template file doesn't have form. It's okay.
D [01/Jun/2016:09:48:48 +0300] [Job 16] PID 4402 (/usr/lib/cups/filter/bannertopdf) exited with no errors.
D [01/Jun/2016:09:48:48 +0300] [Job 16] Calling FindDeviceById(cups-HP-LaserJet-1320)
D [01/Jun/2016:09:48:48 +0300] [Job 16] Found device /org/freedesktop/ColorManager/devices/cups_HP_LaserJet_1320
D [01/Jun/2016:09:48:48 +0300] [Job 16] Calling org.freedesktop.ColorManager.Device.Get(ProfilingInhibitors)
D [01/Jun/2016:09:48:48 +0300] [Job 16] PPD uses qualifier 'Gray.Plain.'
D [01/Jun/2016:09:48:48 +0300] [Job 16] Calling FindDeviceById(cups-HP-LaserJet-1320)
D [01/Jun/2016:09:48:48 +0300] [Job 16] Found device /org/freedesktop/ColorManager/devices/cups_HP_LaserJet_1320
D [01/Jun/2016:09:48:48 +0300] [Job 16] Calling GetProfileForQualifiers(Gray.Plain....)
D [01/Jun/2016:09:48:48 +0300] [Job 16] Found profile /org/freedesktop/ColorManager/profiles/HP_LaserJet_1320_Gray__
D [01/Jun/2016:09:48:48 +0300] [Job 16] Calling org.freedesktop.ColorManager.Profile.Get(Filename)
D [01/Jun/2016:09:48:48 +0300] [Job 16] Use profile filename: ''
D [01/Jun/2016:09:48:48 +0300] [Job 16] Using ICC Profile ''
D [01/Jun/2016:09:48:48 +0300] [Job 16] Ghostscript command line: /usr/bin/gs -dQUIET -dPARANOIDSAFER -dNOPAUSE -dBATCH -dNOINTERPOLATE -sDEVICE=cups -sstdout=%stderr -sOutputFile=%stdout -sMediaType=Plain -sOutputType=0 -r600x600 -dMediaPosition=7 -dDEVICEWIDTHPOINTS=595 -dDEVICEHEIGHTPOINTS=841 -dcupsBitsPerColor=1 -dcupsColorOrder=0 -dcupsColorSpace=3 -dcupsRowCount=1 -dcupsRowStep=2 -dcupsInteger0=26 -scupsPageSizeName=A4 -I/usr/share/cups/fonts -c '<</.HWMargins[18.000000 14.000000 18.000000 14.000000] /Margins[0 0]>>setpagedevice' -f -_
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[0]="CUPS_CACHEDIR=/var/cache/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[1]="CUPS_DATADIR=/usr/share/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[2]="CUPS_DOCROOT=/usr/share/cups/doc-root"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[3]="CUPS_FONTPATH=/usr/share/cups/fonts"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[4]="CUPS_REQUESTROOT=/var/spool/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[5]="CUPS_SERVERBIN=/usr/lib/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[6]="CUPS_SERVERROOT=/etc/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[7]="CUPS_STATEDIR=/var/run/cups"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[8]="HOME=/var/spool/cups/tmp"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[9]="PATH=/usr/lib/cups/filter:/usr/bin:/usr/sbin:/bin:/usr/bin"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[10]="SERVER_ADMIN=root@mikhalev-HP-Compaq-dc7900-Small-Form-Factor"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[11]="SOFTWARE=CUPS/1.7.2"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[12]="TMPDIR=/var/spool/cups/tmp"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[13]="USER=root"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[14]="CUPS_MAX_MESSAGE=2047"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[15]="CUPS_SERVER=/var/run/cups/cups.sock"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[16]="CUPS_ENCRYPTION=IfRequested"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[17]="IPP_PORT=631"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[18]="CHARSET=utf-8"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[19]="LANG=ru_RU.UTF-8"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[20]="PPD=/etc/cups/ppd/HP-LaserJet-1320.ppd"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[21]="RIP_MAX_CACHE=128m"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[22]="CONTENT_TYPE=application/vnd.cups-pdf-banner"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[23]="DEVICE_URI=smb://WORKGROUP/USER-KLO4EK/hp%20LaserJet%201320%20PCL%205"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[24]="PRINTER_INFO=HP LaserJet 1320"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[25]="PRINTER_LOCATION="
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[26]="PRINTER=HP-LaserJet-1320"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[27]="PRINTER_STATE_REASONS=none"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[28]="CUPS_FILETYPE=document"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[29]="FINAL_CONTENT_TYPE=printer/HP-LaserJet-1320"
D [01/Jun/2016:09:48:48 +0300] [Job 16] envp[30]="AUTH_INFO_REQUIRED=none"
D [01/Jun/2016:09:48:48 +0300] [Job 16] PID 4403 (/usr/lib/cups/filter/pdftopdf) exited with no errors.
D [01/Jun/2016:09:48:48 +0300] [Job 16] Start rendering...
D [01/Jun/2016:09:48:48 +0300] [Job 16] Processing page 1...
D [01/Jun/2016:09:48:48 +0300] [Job 16] PID 4405 (/usr/lib/cups/filter/hpcups) did not catch or ignore signal 13.
D [01/Jun/2016:09:48:48 +0300] [Job 16] Processing page 2...
D [01/Jun/2016:09:48:48 +0300] [Job 16] Rendering completed
D [01/Jun/2016:09:48:48 +0300] [Job 16] PID 4404 (/usr/lib/cups/filter/gstoraster) exited with no errors.
D [01/Jun/2016:09:48:48 +0300] [Job 16] Backend returned status 1 (failed)
D [01/Jun/2016:09:48:48 +0300] [Job 16] time-at-completed=1464763728
D [01/Jun/2016:09:48:48 +0300] [Job 16] End of messages
D [01/Jun/2016:09:48:48 +0300] [Job 16] printer-state=3(idle)
D [01/Jun/2016:09:48:48 +0300] [Job 16] printer-state-message="Rendering completed"
D [01/Jun/2016:09:48:48 +0300] [Job 16] printer-state-reasons=none
E [01/Jun/2016:12:01:18 +0300] [cups-deviced] PID 5277 (hpfax) stopped with status 1!
E [01/Jun/2016:12:04:59 +0300] [Job 17] Can't load /etc/samba/smb.conf - run testparm to debug it
E [01/Jun/2016:12:05:45 +0300] [cups-deviced] PID 5355 (hpfax) stopped with status 1!
E [01/Jun/2016:12:10:38 +0300] [Job 18] Can't load /etc/samba/smb.conf - run testparm to debug it

Укажите где еще смотреть.

[MAKAP]

Samba установлена? Он же пишет - кент лоад.

[MikhalevDM]

Да, samba установлена.

[Stanyslav Kovalsky]

Так что там с самба-конфигом? Файл вручную открывается? Содержимое? Права на нем тоже глянуть надобно.

[MikhalevDM]

Вот конфиг самбы

(Нажмите, чтобы показать/скрыть)

#
# Sample configuration file for the Samba suite for Debian GNU/Linux.
#
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options most of which
# are not shown in this example
#
# Some options that are often worth tuning have been included as
# commented-out examples in this file.
#  - When such options are commented with ";", the proposed setting
#    differs from the default Samba behaviour
#  - When commented with "#", the proposed setting is the default
#    behaviour of Samba but the option is considered important
#    enough to be mentioned here
#
# NOTE: Whenever you modify this file you should run the command
# "testparm" to check that you have not made any basic syntactic
# errors.

#======================= Global Settings =======================

[global]
guest account = nobody

security = share

dos charset = cp866

unix charset = UTF-8

## Browsing/Identification ###

# Change this to the workgroup/NT-domain name your Samba server will part of
   workgroup = WORKGROUP

# server string is the equivalent of the NT Description field
   server string = %h server (Samba, Linux Mint)

# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable its WINS Server
#   wins support = no

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
;   wins server = w.x.y.z

# This will prevent nmbd to search for NetBIOS names through DNS.
   dns proxy = no

#### Networking ####

# The specific set of interfaces / networks to bind to
# This can be either the interface name or an IP address/netmask;
# interface names are normally preferred
;   interfaces = 127.0.0.0/8 eth0

# Only bind to the named interfaces and/or networks; you must use the
# 'interfaces' option above to use this.
# It is recommended that you enable this feature if your Samba machine is
# not protected by a firewall or is a firewall itself.  However, this
# option cannot handle dynamic or non-broadcast interfaces correctly.
;   bind interfaces only = yes



#### Debugging/Accounting ####

# This tells Samba to use a separate log file for each machine
# that connects
   log file = /var/log/samba/log.%m

# Cap the size of the individual log files (in KiB).
   max log size = 1000

# If you want Samba to only log through syslog then set the following
# parameter to 'yes'.
#   syslog only = no

# We want Samba to log a minimum amount of information to syslog. Everything
# should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log
# through syslog you should set the following parameter to something higher.
   syslog = 0

# Do something sensible when Samba crashes: mail the admin a backtrace
   panic action = /usr/share/samba/panic-action %d


####### Authentication #######

# Server role. Defines in which mode Samba will operate. Possible
# values are "standalone server", "member server", "classic primary
# domain controller", "classic backup domain controller", "active
# directory domain controller".
#
# Most people will want "standalone sever" or "member server".
# Running as "active directory domain controller" will require first
# running "samba-tool domain provision" to wipe databases and create a
# new domain.
   server role = standalone server

# If you are using encrypted passwords, Samba will need to know what
# password database type you are using. 
   passdb backend = tdbsam

   obey pam restrictions = yes

# This boolean parameter controls whether Samba attempts to sync the Unix
# password with the SMB password when the encrypted SMB password in the
# passdb is changed.
   unix password sync = yes

# For Unix password sync to work on a Debian GNU/Linux system, the following
# parameters must be set (thanks to Ian Kahan <<kahan@informatik.tu-muenchen.de> for
# sending the correct chat script for the passwd program in Debian Sarge).
   passwd program = /usr/bin/passwd %u
   passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* .

# This boolean controls whether PAM will be used for password changes
# when requested by an SMB client instead of the program listed in
# 'passwd program'. The default is 'no'.
   pam password change = yes

# This option controls how unsuccessful authentication attempts are mapped
# to anonymous connections
   map to guest = bad user

########## Domains ###########

#
# The following settings only takes effect if 'server role = primary
# classic domain controller', 'server role = backup domain controller'
# or 'domain logons' is set
#

# It specifies the location of the user's
# profile directory from the client point of view) The following
# required a [profiles] share to be setup on the samba server (see
# below)
;   logon path = \\%N\profiles\%U
# Another common choice is storing the profile in the user's home directory
# (this is Samba's default)
#   logon path = \\%N\%U\profile

# The following setting only takes effect if 'domain logons' is set
# It specifies the location of a user's home directory (from the client
# point of view)
;   logon drive = H:
#   logon home = \\%N\%U

# The following setting only takes effect if 'domain logons' is set
# It specifies the script to run during logon. The script must be stored
# in the [netlogon] share
# NOTE: Must be store in 'DOS' file format convention
;   logon script = logon.cmd

# This allows Unix users to be created on the domain controller via the SAMR
# RPC pipe.  The example command creates a user account with a disabled Unix
# password; please adapt to your needs
; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u

# This allows machine accounts to be created on the domain controller via the
# SAMR RPC pipe. 
# The following assumes a "machines" group exists on the system
; add machine script  = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u

# This allows Unix groups to be created on the domain controller via the SAMR
# RPC pipe. 
; add group script = /usr/sbin/addgroup --force-badname %g

############ Misc ############

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
;   include = /home/samba/etc/smb.conf.%m

# Some defaults for winbind (make sure you're not using the ranges
# for something else.)
;   idmap uid = 10000-20000
;   idmap gid = 10000-20000
;   template shell = /bin/bash

# Setup usershare options to enable non-root users to share folders
# with the net usershare command.

# Maximum number of usershare. 0 (default) means that usershare is disabled.
;   usershare max shares = 100

# Allow users who've been granted usershare privileges to create
# public shares, not just authenticated ones
   usershare allow guests = yes

#======================= Share Definitions =======================

# Un-comment the following (and tweak the other settings below to suit)
# to enable the default home directory shares. This will share each
# user's home directory as \\server\username
;[homes]
;   comment = Home Directories
;   browseable = no

# By default, the home directories are exported read-only. Change the
# next parameter to 'no' if you want to be able to write to them.
;   read only = yes

# File creation mask is set to 0700 for security reasons. If you want to
# create files with group=rw permissions, set next parameter to 0775.
;   create mask = 0700

# Directory creation mask is set to 0700 for security reasons. If you want to
# create dirs. with group=rw permissions, set next parameter to 0775.
;   directory mask = 0700

# By default, \\server\username shares can be connected to by anyone
# with access to the samba server.
# Un-comment the following parameter to make sure that only "username"
# can connect to \\server\username
# This might need tweaking when using external authentication schemes
;   valid users = %S

# Un-comment the following and create the netlogon directory for Domain Logons
# (you need to configure Samba to act as a domain controller too.)
;[netlogon]
;   comment = Network Logon Service
;   path = /home/samba/netlogon
;   guest ok = yes
;   read only = yes

# Un-comment the following and create the profiles directory to store
# users profiles (see the "logon path" option above)
# (you need to configure Samba to act as a domain controller too.)
# The path below should be writable by all users so that their
# profile directory may be created the first time they log on
;[profiles]
;   comment = share
;   path = /home/samba/profiles
;   guest ok = yes
;   browseable = no
;   create mask = 0600
;   directory mask = 0700

[printers]
   comment = All Printers
   browseable = no
   path = /var/spool/samba
   printable = yes
   guest ok = no
   read only = yes
   create mask = 0700

# Windows clients look for this share name as a source of downloadable
# printer drivers
[print$]
   comment = Printer Drivers
   path = /var/lib/samba/printers
   browseable = yes
   read only = yes
   guest ok = no
# Uncomment to allow remote administration of Windows print drivers.
# You may need to replace 'lpadmin' with the name of the group your
# admin users are members of.
# Please note that you also need to set appropriate Unix permissions
# to the drivers directory for these users to have write rights in it
;   write list = root, @lpadmin

Отправляю на печать, встает в очередь. Смотрю очередь печати - простаивает