Здравствуйте,
Вопрос такой. Решил вставить в комп две карты ASUS NX1001 одна из них завелась вторая видится в системе, но ее MAC адрес 00:00:00:00 .... поднять интерфейс не удается.
lspci -vv дает следующее:
для рабочей карты:
03:04.0 Ethernet controller: Sundance Technology Inc / IC Plus Corp IC Plus IP100A Integrated 10/100 Ethernet MAC + PHY (rev 31)
Subsystem: ASUSTeK Computer Inc. Device 8213
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at cc00 [size=128]
Region 1: Memory at dfdffe00 (32-bit, non-prefetchable) [size=512]
Expansion ROM at 20000000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=2 PME-
Kernel driver in use: sundance
Kernel modules: sundance
Для нерабочей карты:
03:06.0 Ethernet controller: Sundance Technology Inc / IC Plus Corp IC Plus IP100A Integrated 10/100 Ethernet MAC + PHY (rev 31)
Subsystem: ASUSTeK Computer Inc. Device 0213
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at c800 [size=128]
Region 1: Memory at 5fdffc00 (32-bit, non-prefetchable) [size=512]
Expansion ROM at <ignored> [disabled]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sundance
Kernel modules: sundance
ifconfig :
нерабочая: eth1 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:1048560 errors:0 dropped:4080 overruns:0 frame:0
TX packets:1048560 errors:0 dropped:0 overruns:0 carrier:4080
collisions:11985 txqueuelen:1000
RX bytes:4294901745 (4.2 GB) TX bytes:131056 (131.0 KB)
Interrupt:19 Base address:0xc800
рабочая: eth0_rename Link encap:Ethernet HWaddr 00:26:18:d9:80:08
inet addr:192.168.50.2 Bcast:192.168.50.255 Mask:255.255.255.0
inet6 addr: fe80::226:18ff:fed9:8008/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:20
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:3829 (3.8 KB)
Interrupt:17 Base address:0xcc00
может надо как-то ядро самому собрать, чтобы две карты одновременно заработали?
Тема: две карты ASUS NX1001 на Karmic (Прочитано 925 раз)
