Помогите обновить Ubuntu на Orange Pi Prime

[SimpleHosting]

Да вон один полный логов диск в оперативке. 50 мегабайт. перезагружайся.
потом:
Установи из предыдущих постов xinit

(Нажмите, чтобы показать/скрыть)

login as: root
root@192.168.1.3's password:
  ___                               ____  _   ____       _
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |  _ \ _ __(_)_ __ ___   ___
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | |_) | '__| | '_ ` _ \ / _ \
| |_| | | | (_| | | | | (_| |  __/ |  __/| | |  __/| |  | | | | | | |  __/
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| |_|   |_|  |_|_| |_| |_|\___|
                       |___/

Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi64
System load:   0.08 0.07 0.03   Up time:       5 min
Memory usage:  4 % of 2002MB    IP:            192.168.1.3
CPU temp:      20°C
Usage of /:    4% of 59G

[ General system configuration (beta): armbian-config ]

Last login: Sun Apr 29 14:42:15 2018 from 192.168.1.2

root@orangepiprime:~# apt install -y xinit
Reading package lists... Done
Building dependency tree
Reading state information... Done
xinit is already the newest version (1.3.4-3+b1).
xinit set to manually installed.
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
root@orangepiprime:~#

ксати выведи сперва

Код: [Выделить]

dmesgможет у тебя ядро ошибками сыпет что лог забило.

(Нажмите, чтобы показать/скрыть)

root@orangepiprime:~# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.18-sunxi64 (root@xeon) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #26 SMP Fri Feb 9 17:14:48 CET 2018
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] Machine model: Xunlong Orange Pi Prime
[    0.000000] cma: Reserved 128 MiB at 0x00000000b8000000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000bfffffff]
[    0.000000] NUMA: NODE_DATA [mem 0xb7fcbf80-0xb7fcda7f]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x00000000bfffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000000bfffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff]
[    0.000000] On node 0 totalpages: 524288
[    0.000000]   DMA zone: 8192 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 524288 pages, LIFO batch:31
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv0.2 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] random: fast init done
[    0.000000] percpu: Embedded 21 pages/cpu @ffff800077f72000 s45592 r8192 d32232 u86016
[    0.000000] pcpu-alloc: s45592 r8192 d32232 u86016 alloc=21*4096
[    0.000000] pcpu-alloc:

• 0
• 1
• 2
• 3

[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516096
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: root=UUID=a2a90d4d-5aa6-4dd7-979f-cf0ff08bcda2 rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 panic=10 consoleblank=0 loglevel=1 ubootpart=089c372c-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u   cgroup_enable=memory swapaccount=1
[    0.000000] log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] log_buf_len total cpu_extra contributions: 12288 bytes
[    0.000000] log_buf_len min size: 16384 bytes
[    0.000000] log_buf_len: 32768 bytes
[    0.000000] early log buf free: 14048(85%)
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Memory: 1914416K/2097152K available (9150K kernel code, 672K rwdata, 2332K rodata, 448K init, 316K bss, 51664K reserved, 131072K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffff000000000000 - 0xffff000008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 GB)
[    0.000000]       .text : 0xffff000008080000 - 0xffff000008970000   (  9152 KB)
[    0.000000]     .rodata : 0xffff000008970000 - 0xffff000008bc0000   (  2368 KB)
[    0.000000]       .init : 0xffff000008bc0000 - 0xffff000008c30000   (   448 KB)
[    0.000000]       .data : 0xffff000008c30000 - 0xffff000008cd8008   (   673 KB)
[    0.000000]        .bss : 0xffff000008cd8008 - 0xffff000008d271d8   (   317 KB)
[    0.000000]     fixed   : 0xffff7dfffe7fd000 - 0xffff7dfffec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 GB maximum)
[    0.000000]               0xffff7e0000000000 - 0xffff7e0002000000   (    32 MB actual)
[    0.000000]     memory  : 0xffff800000000000 - 0xffff800080000000   (  2048 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000140] Console: colour dummy device 80x25
[    0.000154] console [tty1] enabled
[    0.000215] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.000224] pid_max: default: 32768 minimum: 301
[    0.000324] Security Framework initialized
[    0.000333] AppArmor: AppArmor disabled by boot time parameter
[    0.001621] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.002267] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.002312] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.002336] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.003526] ASID allocator initialised with 65536 entries
[    0.003594] Hierarchical SRCU implementation.
[    0.004056] smp: Bringing up secondary CPUs ...
[    0.005174] Detected VIPT I-cache on CPU1
[    0.005230] CPU1: Booted secondary processor [410fd034]
[    0.005948] Detected VIPT I-cache on CPU2
[    0.005976] CPU2: Booted secondary processor [410fd034]
[    0.006655] Detected VIPT I-cache on CPU3
[    0.006681] CPU3: Booted secondary processor [410fd034]
[    0.006747] smp: Brought up 1 node, 4 CPUs
[    0.006751] SMP: Total of 4 processors activated.
[    0.006757] CPU features: detected feature: 32-bit EL0 Support
[    0.006873] CPU: All CPU(s) started at EL2
[    0.006893] alternatives: patching kernel code
[    0.008133] devtmpfs: initialized
[    0.013793] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.013844] futex hash table entries: 1024 (order: 5, 131072 bytes)
[    0.018071] xor: measuring software checksum speed
[    0.056110]    8regs     :  1566.000 MB/sec
[    0.096145]    8regs_prefetch:  1396.000 MB/sec
[    0.136186]    32regs    :  1925.000 MB/sec
[    0.176229]    32regs_prefetch:  1619.000 MB/sec
[    0.176233] xor: using function: 32regs (1925.000 MB/sec)
[    0.176246] pinctrl core: initialized pinctrl subsystem
[    0.177023] NET: Registered protocol family 16
[    0.177997] cpuidle: using governor menu
[    0.178724] vdso: 2 pages (1 code @ ffff000008976000, 1 data @ ffff000008c34000)
[    0.178738] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.179895] DMA: preallocated 256 KiB pool for atomic allocations
[    0.179968] Serial: AMBA PL011 UART driver
[    0.191783] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.260499] raid6: int64x1  gen()   299 MB/s
[    0.328430] raid6: int64x1  xor()   300 MB/s
[    0.396601] raid6: int64x2  gen()   460 MB/s
[    0.464556] raid6: int64x2  xor()   409 MB/s
[    0.532646] raid6: int64x4  gen()   707 MB/s
[    0.600710] raid6: int64x4  xor()   519 MB/s
[    0.668784] raid6: int64x8  gen()   667 MB/s
[    0.736841] raid6: int64x8  xor()   510 MB/s
[    0.804884] raid6: neonx1   gen()   494 MB/s
[    0.872973] raid6: neonx1   xor()   579 MB/s
[    0.941015] raid6: neonx2   gen()   790 MB/s
[    1.009072] raid6: neonx2   xor()   819 MB/s
[    1.077153] raid6: neonx4   gen()  1028 MB/s
[    1.145193] raid6: neonx4   xor()   981 MB/s
[    1.213281] raid6: neonx8   gen()  1125 MB/s
[    1.281337] raid6: neonx8   xor()  1042 MB/s
[    1.281340] raid6: using algorithm neonx8 gen() 1125 MB/s
[    1.281343] raid6: .... xor() 1042 MB/s, rmw enabled
[    1.281346] raid6: using neon recovery algorithm
[    1.282474] SCSI subsystem initialized
[    1.282645] usbcore: registered new interface driver usbfs
[    1.282679] usbcore: registered new interface driver hub
[    1.282740] usbcore: registered new device driver usb
[    1.282954] pps_core: LinuxPPS API ver. 1 registered
[    1.282957] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.282971] PTP clock support registered
[    1.283271] Advanced Linux Sound Architecture Driver Initialized.
[    1.284057] clocksource: Switched to clocksource arch_sys_counter
[    1.284180] VFS: Disk quotas dquot_6.6.0
[    1.284233] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.290486] NET: Registered protocol family 2
[    1.291007] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    1.291211] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    1.291521] TCP: Hash tables configured (established 16384 bind 16384)
[    1.291667] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    1.291729] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    1.291938] NET: Registered protocol family 1
[    1.292330] RPC: Registered named UNIX socket transport module.
[    1.292334] RPC: Registered udp transport module.
[    1.292336] RPC: Registered tcp transport module.
[    1.292339] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.292555] Unpacking initramfs...
[    1.578150] Freeing initrd memory: 4808K
[    1.582856] audit: initializing netlink subsys (disabled)
[    1.582985] audit: type=2000 audit(1.576:1): state=initialized audit_enabled=0 res=1
[    1.583248] workingset: timestamp_bits=44 max_order=19 bucket_order=0
[    1.588181] zbud: loaded
[    1.589833] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.590465] NFS: Registering the id_resolver key type
[    1.590489] Key type id_resolver registered
[    1.590492] Key type id_legacy registered
[    1.590503] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.590506] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.591325] 9p: Installing v9fs 9p2000 file system support
[    1.596244] NET: Registered protocol family 38
[    1.596530] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.596626] io scheduler noop registered
[    1.596630] io scheduler deadline registered
[    1.596841] io scheduler cfq registered (default)
[    1.596846] io scheduler mq-deadline registered
[    1.596849] io scheduler kyber registered
[    1.596888] io scheduler bfq registered
[    1.597459] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO
[    1.599415] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
[    1.602798] sun50i-h5-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    1.610055] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.611188] console [ttyS0] disabled
[    1.631365] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 29, base_baud = 1500000) is a U6_16550A
[    1.631413] console [ttyS0] enabled
[    1.632461] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    1.636764] loop: module loaded
[    1.637476] libphy: Fixed MDIO Bus: probed
[    1.638272] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[    1.638938] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.638942] ehci-platform: EHCI generic platform driver
[    1.639095] ehci-platform 1c1a000.usb: EHCI Host Controller
[    1.639118] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
[    1.639615] ehci-platform 1c1a000.usb: irq 12, io mem 0x01c1a000
[    1.652078] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[    1.652300] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.652307] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.652312] usb usb1: Product: EHCI Host Controller
[    1.652318] usb usb1: Manufacturer: Linux 4.14.18-sunxi64 ehci_hcd
[    1.652323] usb usb1: SerialNumber: 1c1a000.usb
[    1.652780] hub 1-0:1.0: USB hub found
[    1.652821] hub 1-0:1.0: 1 port detected
[    1.653457] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.653496] ohci-platform: OHCI generic platform driver
[    1.653675] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[    1.653698] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[    1.653895] ohci-platform 1c1a400.usb: irq 13, io mem 0x01c1a400
[    1.716275] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.716282] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.716288] usb usb2: Product: Generic Platform OHCI controller
[    1.716293] usb usb2: Manufacturer: Linux 4.14.18-sunxi64 ohci_hcd
[    1.716298] usb usb2: SerialNumber: 1c1a400.usb
[    1.716692] hub 2-0:1.0: USB hub found
[    1.716728] hub 2-0:1.0: 1 port detected
[    1.717402] usbcore: registered new interface driver usb-storage
[    1.717661] mousedev: PS/2 mouse device common for all mice
[    1.718088] sun6i-rtc 1f00000.rtc: rtc core: registered rtc-sun6i as rtc0
[    1.718094] sun6i-rtc 1f00000.rtc: RTC enabled
[    1.718167] i2c /dev entries driver
[    1.719193] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.719832] sdhci: Secure Digital Host Controller Interface driver
[    1.719835] sdhci: Copyright(c) Pierre Ossman
[    1.719858] Synopsys Designware Multimedia Card Interface Driver
[    1.721095] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[    1.760236] sunxi-mmc 1c0f000.mmc: base:0xffff000009045000 irq:9
[    1.761024] sunxi-mmc 1c10000.mmc: allocated mmc-pwrseq
[    1.800075] sunxi-mmc 1c10000.mmc: base:0xffff000009055000 irq:10
[    1.800305] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.800948] ledtrig-cpu: registered to indicate activity on CPUs
[    1.801178] hidraw: raw HID events driver (C) Jiri Kosina
[    1.801285] usbcore: registered new interface driver usbhid
[    1.801288] usbhid: USB HID core driver
[    1.801662] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.802092] NET: Registered protocol family 10
[    1.813435] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.814664] Segment Routing with IPv6
[    1.814751] NET: Registered protocol family 17
[    1.814811] 8021q: 802.1Q VLAN Support v1.8
[    1.814859] 9pnet: Installing 9P2000 support
[    1.814946] Key type dns_resolver registered
[    1.815627] registered taskstats version 1
[    1.815734] zswap: loaded using pool lzo/zbud
[    1.816941] mmc0: new high speed SDXC card at address 0001
[    1.816959] Btrfs loaded, crc32c=crc32c-arm64-ce
[    1.817438] mmcblk0: mmc0:0001 EC2QT 59.6 GiB
[    1.818479]  mmcblk0: p1
[    1.822792] Key type encrypted registered
[    1.829347] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[    1.835410] mmc1: new high speed SDIO card at address 0001
[    1.936121] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
[    1.936128] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
[    1.936133] dwmac-sun8i 1c30000.ethernet: Normal descriptors
[    1.936138] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
[    1.936143] dwmac-sun8i 1c30000.ethernet: COE Type 2
[    1.936148] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
[    1.936236] libphy: stmmac: probed
[    1.936791] dwmac-sun8i 1c30000.ethernet: Found internal PHY node
[    1.936865] libphy: mdio_mux: probed
[    1.936883] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY
[    1.936889] dwmac-sun8i 1c30000.ethernet: Powering internal PHY
[    1.940124] libphy: mdio_mux: probed
[    1.940150] dwmac-sun8i 1c30000.ethernet: Switch mux to external PHY
[    1.943547] ehci-platform 1c1b000.usb: EHCI Host Controller
[    1.943575] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 3
[    1.943993] ehci-platform 1c1b000.usb: irq 14, io mem 0x01c1b000
[    1.956076] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00
[    1.956241] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    1.956248] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.956254] usb usb3: Product: EHCI Host Controller
[    1.956259] usb usb3: Manufacturer: Linux 4.14.18-sunxi64 ehci_hcd
[    1.956264] usb usb3: SerialNumber: 1c1b000.usb
[    1.956720] hub 3-0:1.0: USB hub found
[    1.956755] hub 3-0:1.0: 1 port detected
[    1.957364] ehci-platform 1c1c000.usb: EHCI Host Controller
[    1.957383] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 4
[    1.957669] ehci-platform 1c1c000.usb: irq 16, io mem 0x01c1c000
[    1.972072] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[    1.972206] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[    1.972213] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.972218] usb usb4: Product: EHCI Host Controller
[    1.972223] usb usb4: Manufacturer: Linux 4.14.18-sunxi64 ehci_hcd
[    1.972229] usb usb4: SerialNumber: 1c1c000.usb
[    1.972603] hub 4-0:1.0: USB hub found
[    1.972631] hub 4-0:1.0: 1 port detected
[    1.973178] ehci-platform 1c1d000.usb: EHCI Host Controller
[    1.973201] ehci-platform 1c1d000.usb: new USB bus registered, assigned bus number 5
[    1.973476] ehci-platform 1c1d000.usb: irq 18, io mem 0x01c1d000
[    1.988072] ehci-platform 1c1d000.usb: USB 2.0 started, EHCI 1.00
[    1.988202] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    1.988209] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.988215] usb usb5: Product: EHCI Host Controller
[    1.988220] usb usb5: Manufacturer: Linux 4.14.18-sunxi64 ehci_hcd
[    1.988225] usb usb5: SerialNumber: 1c1d000.usb
[    1.988618] hub 5-0:1.0: USB hub found
[    1.988645] hub 5-0:1.0: 1 port detected
[    1.989188] ohci-platform 1c1b400.usb: Generic Platform OHCI controller
[    1.989206] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 6
[    1.989387] ohci-platform 1c1b400.usb: irq 15, io mem 0x01c1b400
[    2.052210] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    2.052217] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.052222] usb usb6: Product: Generic Platform OHCI controller
[    2.052228] usb usb6: Manufacturer: Linux 4.14.18-sunxi64 ohci_hcd
[    2.052233] usb usb6: SerialNumber: 1c1b400.usb
[    2.052595] hub 6-0:1.0: USB hub found
[    2.052623] hub 6-0:1.0: 1 port detected
[    2.053156] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[    2.053174] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 7
[    2.053352] ohci-platform 1c1c400.usb: irq 17, io mem 0x01c1c400
[    2.116203] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    2.116210] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.116216] usb usb7: Product: Generic Platform OHCI controller
[    2.116221] usb usb7: Manufacturer: Linux 4.14.18-sunxi64 ohci_hcd
[    2.116227] usb usb7: SerialNumber: 1c1c400.usb
[    2.116602] hub 7-0:1.0: USB hub found
[    2.116634] hub 7-0:1.0: 1 port detected
[    2.117180] ohci-platform 1c1d400.usb: Generic Platform OHCI controller
[    2.117199] ohci-platform 1c1d400.usb: new USB bus registered, assigned bus number 8
[    2.117388] ohci-platform 1c1d400.usb: irq 19, io mem 0x01c1d400
[    2.180205] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[    2.180212] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.180217] usb usb8: Product: Generic Platform OHCI controller
[    2.180223] usb usb8: Manufacturer: Linux 4.14.18-sunxi64 ohci_hcd
[    2.180228] usb usb8: SerialNumber: 1c1d400.usb
[    2.180596] hub 8-0:1.0: USB hub found
[    2.180623] hub 8-0:1.0: 1 port detected
[    2.181500] input: r-gpio-keys as /devices/platform/r-gpio-keys/input/input0
[    2.181832] of_cfs_init
[    2.181914] of_cfs_init: OK
[    2.182056] vdd-cpux-dummy: disabling
[    2.182063] usb0-vbus: disabling
[    2.182066] ALSA device list:
[    2.182069]   No soundcards found.
[    2.182560] Freeing unused kernel memory: 448K
[    2.345560] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[    2.346227] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[    2.346250] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 9
[    2.346782] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002
[    2.346794] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.346800] usb usb9: Product: MUSB HDRC host driver
[    2.346805] usb usb9: Manufacturer: Linux 4.14.18-sunxi64 musb-hcd
[    2.346811] usb usb9: SerialNumber: musb-hdrc.1.auto
[    2.347581] hub 9-0:1.0: USB hub found
[    2.347707] hub 9-0:1.0: 1 port detected
[    2.379053] thermal thermal_zone0: binding zone cpu-thermal with cdev thermal-cpufreq-0 failed:-17
[    2.896114] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
[    3.546171] systemd[1]: System time before build time, advancing clock.
[    3.588731] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[    3.589499] systemd[1]: Detected architecture arm64.
[    3.614659] systemd[1]: Set hostname to <orangepiprime>.
[    4.086529] systemd[1]: Listening on udev Control Socket.
[    4.100662] systemd[1]: Listening on Journal Audit Socket.
[    4.112440] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    4.129886] systemd[1]: Listening on fsck to fsckd communication Socket.
[    4.140371] systemd[1]: Listening on Journal Socket.
[    4.156168] systemd[1]: Created slice System Slice.
[    4.176861] systemd[1]: Starting Load Kernel Modules...
[    4.310917] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro
[    4.833869] Adding 131068k swap on /var/swap.  Priority:-2 extents:2 across:163836k SSFS
[    5.521913] sun4i-codec 1c22c00.codec: ASoC: /soc/codec-analog@01f015c0 not registered
[    5.521926] sun4i-codec 1c22c00.codec: Failed to register our card
[    5.604544] thermal thermal_zone0: failed to read out thermal zone (-110)
[    5.606012] sun4i-codec 1c22c00.codec: ASoC: /soc/codec-analog@01f015c0 not registered
[    5.606024] sun4i-codec 1c22c00.codec: Failed to register our card
[    5.658009] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok
[    5.798615] lirc_dev: IR Remote Control driver registered, major 244
[    5.807137] IR LIRC bridge handler initialized
[    5.807847] Registered IR keymap rc-empty
[    5.807956] rc rc0: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0
[    5.808109] input: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0/input1
[    5.808877] rc rc0: lirc_dev: driver ir-lirc-codec (sunxi-ir) registered at minor = 0
[    5.808999] sunxi-ir 1f02000.ir: initialized sunXi IR driver
[    5.839388] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    5.839394] [drm] No driver support for vblank timestamp query.
[    5.846194] sun4i-drm display-engine: bound 1100000.mixer (ops sun8i_mixer_platform_driver_exit [sun8i_mixer])
[    5.846505] sun4i-drm display-engine: No panel or bridge found... RGB output disabled
[    5.846524] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops sun4i_tcon_platform_driver_exit [sun4i_tcon])
[    5.971438] sun8i-dw-hdmi 1ee0000.hdmi: Detected HDMI TX controller v1.32a with HDCP (sun8i_dw_hdmi_phy)
[    5.972102] sun8i-dw-hdmi 1ee0000.hdmi: registered DesignWare HDMI I2C bus driver
[    5.972465] sun4i-drm display-engine: bound 1ee0000.hdmi (ops sun8i_dw_hdmi_ops [sun8i_dw_hdmi])
[    5.972504] [drm] Cannot find any crtc or sizes
[    5.973054] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0
[    6.072081] Registered IR keymap rc-cec
[    6.072375] rc rc1: RC for dw_hdmi as /devices/platform/soc/1ee0000.hdmi/rc/rc1
[    6.072667] input: RC for dw_hdmi as /devices/platform/soc/1ee0000.hdmi/rc/rc1/input2
[    6.194922] asoc-simple-card sound: i2s-hifi <-> 1c22800.i2s mapping ok
[    6.273272] r8723bs: module is from the staging directory, the quality is unknown, you have been warned.
[    6.280003] RTL8723BS: module init start
[    6.280013] RTL8723BS: rtl8723bs v4.3.5.5_12290.20140916_BTCOEX20140507-4E40
[    6.280016] RTL8723BS: rtl8723bs BT-Coex version = BTCOEX20140507-4E40
[    6.280739] pnetdev = ffff800073ca4000
[    6.352799] RTL8723BS: rtw_ndev_init(wlan0)
[    6.354542] RTL8723BS: module init ret =0
[    6.628144] thermal thermal_zone0: failed to read out thermal zone (-110)
[    6.985517] [drm] Cannot find any crtc or sizes
[    7.652127] thermal thermal_zone0: failed to read out thermal zone (-110)
[    7.916570] RTL8211E Gigabit Ethernet 0.2:01: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=0.2:01, irq=POLL)
[    7.918193] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available
[    7.918203] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW
[    7.918433] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    8.203142] random: crng init done
[    8.754889] systemd[1]: Started Armbian enhanced Log2Ram.
[    8.778228] systemd[1]: Starting Journal Service...
[    8.898716] systemd[1]: Started Journal Service.
[    8.953659] systemd-journald[524]: Received request to flush runtime journal from PID 1
[   10.983451] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[   10.983490] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   11.571320] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   11.576701] rtl8723bs: acquire FW from file:rtlwifi/rtl8723bs_nic.bin
[   12.818312] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   13.557839] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
root@orangepiprime:~#

[hesoyamatogun]

нет всё норм.

Код: [Выделить]

apt install -y task-xfce-desktopманагер постаил нет не помню

Код: [Выделить]

apt install -y lightdm

[SimpleHosting]

.

(Нажмите, чтобы показать/скрыть)

login as: root
root@192.168.1.3's password:
  ___                               ____  _   ____       _
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |  _ \ _ __(_)_ __ ___   ___
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | |_) | '__| | '_ ` _ \ / _ \
| |_| | | | (_| | | | | (_| |  __/ |  __/| | |  __/| |  | | | | | | |  __/
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| |_|   |_|  |_|_| |_| |_|\___|
                       |___/

Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi64
System load:   0.30 0.21 0.08   Up time:       1 min
Memory usage:  4 % of 2002MB    IP:            192.168.1.3
CPU temp:      15°C
Usage of /:    4% of 59G

Last login: Sun Apr 29 14:49:41 2018 from 192.168.1.2

root@orangepiprime:~# apt install -y task-xfce-desktop
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following additional packages will be installed:
  desktop-base libxss1 light-locker task-desktop
Recommended packages:
  xdg-utils avahi-daemon libnss-mdns anacron eject xfce4-goodies
  xfce4-power-manager xfce4-mixer xfce4-terminal mousepad libreoffice-gtk2
  xsane vlc quodlibet evince-gtk | evince tango-icon-theme
  network-manager-gnome synaptic firefox-esr | firefox libreoffice
  libreoffice-help-en-us mythes-en-us hunspell-en-us hyphen-en-us
  system-config-printer gnome-orca
The following NEW packages will be installed:
  desktop-base libxss1 light-locker task-desktop task-xfce-desktop
0 upgraded, 5 newly installed, 0 to remove and 0 not upgraded.
Need to get 3,769 kB of archives.
After this operation, 9,021 kB of additional disk space will be used.
Get:1 http://cdn-fastly.deb.debian.org/debian stretch/main arm64 desktop-base all 9.0.2+deb9u1 [3,507 kB]
Get:2 http://cdn-fastly.deb.debian.org/debian stretch/main arm64 libxss1 arm64 1:1.2.2-1 [15.8 kB]
Get:3 http://cdn-fastly.deb.debian.org/debian stretch/main arm64 light-locker arm64 1.7.0-3 [245 kB]
Get:4 http://cdn-fastly.deb.debian.org/debian stretch/main arm64 task-desktop all 3.39 [898 B]
Get:5 http://cdn-fastly.deb.debian.org/debian stretch/main arm64 task-xfce-desktop all 3.39 [1,068 B]
Fetched 3,769 kB in 1s (2,104 kB/s)
Selecting previously unselected package desktop-base.
(Reading database ... 51485 files and directories currently installed.)
Preparing to unpack .../desktop-base_9.0.2+deb9u1_all.deb ...
Unpacking desktop-base (9.0.2+deb9u1) ...
Selecting previously unselected package libxss1:arm64.
Preparing to unpack .../libxss1_1%3a1.2.2-1_arm64.deb ...
Unpacking libxss1:arm64 (1:1.2.2-1) ...
Selecting previously unselected package light-locker.
Preparing to unpack .../light-locker_1.7.0-3_arm64.deb ...
Unpacking light-locker (1.7.0-3) ...
Selecting previously unselected package task-desktop.
Preparing to unpack .../task-desktop_3.39_all.deb ...
Unpacking task-desktop (3.39) ...
Selecting previously unselected package task-xfce-desktop.
Preparing to unpack .../task-xfce-desktop_3.39_all.deb ...
Unpacking task-xfce-desktop (3.39) ...
Processing triggers for libglib2.0-0:arm64 (2.50.3-2) ...
Setting up libxss1:arm64 (1:1.2.2-1) ...
Setting up desktop-base (9.0.2+deb9u1) ...
update-alternatives: using /usr/share/desktop-base/softwaves-theme to provide /usr/share/desktop-base/active-theme (desktop-theme) in auto mode
update-alternatives: using /usr/share/desktop-base/active-theme/wallpaper/contents/images/1920x1080.svg to provide /usr/share/images/desktop-base/desktop-background (desktop-background) in auto mode
update-alternatives: using /usr/share/desktop-base/active-theme/wallpaper/gnome-background.xml to provide /usr/share/images/desktop-base/desktop-background.xml (desktop-background.xml) in auto mode
update-alternatives: using /usr/share/desktop-base/active-theme/lockscreen/gnome-background.xml to provide /usr/share/images/desktop-base/desktop-lockscreen.xml (desktop-lockscreen.xml) in auto mode
update-alternatives: using /usr/share/desktop-base/active-theme/wallpaper to provide /usr/share/wallpapers/DebianTheme (desktop-plasma5-wallpaper) in auto mode
update-alternatives: using /usr/share/desktop-base/active-theme/login/background.svg to provide /usr/share/images/desktop-base/login-background.svg (desktop-login-background) in auto mode
update-alternatives: using /usr/share/desktop-base/active-theme/grub/grub-4x3.png to provide /usr/share/images/desktop-base/desktop-grub.png (desktop-grub) in auto mode
update-initramfs: deferring update (trigger activated)
Processing triggers for man-db (2.7.6.1-2) ...
Processing triggers for hicolor-icon-theme (0.15-1) ...
Setting up task-desktop (3.39) ...
Setting up light-locker (1.7.0-3) ...
Setting up task-xfce-desktop (3.39) ...
Processing triggers for initramfs-tools (0.130) ...
update-initramfs: Generating /boot/initrd.img-4.14.18-sunxi64
update-initramfs: Converting to u-boot format
E: Write error - ~LZMAFILE (28: No space left on device)
root@orangepiprime:~#

Пользователь добавил сообщение 29 Апреля 2018, 18:00:57:

манагер постаил нет не помню

Код: [Выделить]

apt install -y lightdm

(Нажмите, чтобы показать/скрыть)

login as: root
root@192.168.1.3's password:
  ___                               ____  _   ____       _
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |  _ \ _ __(_)_ __ ___   ___
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | |_) | '__| | '_ ` _ \ / _ \
| |_| | | | (_| | | | | (_| |  __/ |  __/| | |  __/| |  | | | | | | |  __/
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| |_|   |_|  |_|_| |_| |_|\___|
                       |___/

Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi64
System load:   0.38 0.17 0.06   Up time:       1 min
Memory usage:  4 % of 2002MB    IP:            192.168.1.3
CPU temp:      19°C
Usage of /:    4% of 59G

Last login: Sun Apr 29 14:57:50 2018 from 192.168.1.2

root@orangepiprime:~# apt install -y lightdm
Reading package lists... Done
Building dependency tree
Reading state information... Done
lightdm is already the newest version (1.18.3-1).
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
root@orangepiprime:~#

[hesoyamatogun]

Это он что то на лог-диск пытается писать. На это можно забить.
поставь

Код: [Выделить]

apt install -y lightdmпотом reboot
Логинешься под алексом. и startx

[SimpleHosting]

Это он что то на лог-диск пытается писать. На это можно забить.
поставь

Код: [Выделить]

apt install -y lightdm

(Нажмите, чтобы показать/скрыть)

login as: root
root@192.168.1.3's password:
  ___                               ____  _   ____       _
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |  _ \ _ __(_)_ __ ___   ___
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | |_) | '__| | '_ ` _ \ / _ \
| |_| | | | (_| | | | | (_| |  __/ |  __/| | |  __/| |  | | | | | | |  __/
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| |_|   |_|  |_|_| |_| |_|\___|
                       |___/

Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi64
System load:   1.58 0.75 0.29   Up time:       2 min
Memory usage:  4 % of 2002MB    IP:            192.168.1.3
CPU temp:      20°C
Usage of /:    4% of 59G

Last login: Sun Apr 29 14:59:42 2018 from 192.168.1.2

root@orangepiprime:~# apt install -y lightdm
Reading package lists... Done
Building dependency tree
Reading state information... Done
lightdm is already the newest version (1.18.3-1).
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
root@orangepiprime:~#

потом reboot
Логинешься под алексом. и startx

(Нажмите, чтобы показать/скрыть)

login as: maxim
maxim@192.168.1.3's password:
  ___                               ____  _   ____       _
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |  _ \ _ __(_)_ __ ___   ___
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | |_) | '__| | '_ ` _ \ / _ \
| |_| | | | (_| | | | | (_| |  __/ |  __/| | |  __/| |  | | | | | | |  __/
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| |_|   |_|  |_|_| |_| |_|\___|
                       |___/

Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi64
System load:   2.04 0.65 0.23   Up time:       1 min
Memory usage:  4 % of 2002MB    IP:            192.168.1.3
CPU temp:      23°C
Usage of /:    4% of 59G

[ General system configuration (beta): armbian-config ]

Last login: Sun Apr 29 15:05:51 2018 from 192.168.1.2

maxim@orangepiprime:~$ startx


X.Org X Server 1.19.2
Release Date: 2017-03-02
X Protocol Version 11, Revision 0
Build Operating System: Linux 4.9.0-4-arm64 aarch64 Debian
Current Operating System: Linux orangepiprime 4.14.18-sunxi64 #26 SMP Fri Feb 9 17:14:48 CET 2018 aarch64
Kernel command line: root=UUID=a2a90d4d-5aa6-4dd7-979f-cf0ff08bcda2 rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 panic=10 consoleblank=0 loglevel=1 ubootpart=089c372c-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u   cgroup_enable=memory swapaccount=1
Build Date: 16 October 2017  08:11:43AM
xorg-server 2:1.19.2-1+deb9u2 (https://www.debian.org/support)
Current version of pixman: 0.34.0
        Before reporting problems, check http://wiki.x.org
        to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
        (++) from command line, (!!) notice, (II) informational,
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/home/maxim/.local/share/xorg/Xorg.1.log", Time: Sun Apr 29 15:06:44 2018
(==) Using config directory: "/etc/X11/xorg.conf.d"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
(EE)
Fatal server error:
(EE) parse_vt_settings: Cannot open /dev/tty0 (Permission denied)
(EE)
(EE)
Please consult the The X.Org Foundation support
         at http://wiki.x.org
 for help.
(EE) Please also check the log file at "/home/maxim/.local/share/xorg/Xorg.1.log" for additional information.
(EE)
(EE) Server terminated with error (1). Closing log file.
xinit: giving up
xinit: unable to connect to X server: Connection refused
xinit: server error
Couldn't get a file descriptor referring to the console
maxim@orangepiprime:~$

[hesoyamatogun]

дай права алексу на 1ю консоль. зачемто ему она понадобилась

от рута

Код: [Выделить]

chmod 777 /dev/tty0
от алекса, не перезагружаясь

Код: [Выделить]

startx

[SimpleHosting]

дай права алексу на 1ю консоль. зачемто ему она понадобилась

от рута

Код: [Выделить]

chmod 777 /dev/tty0

(Нажмите, чтобы показать/скрыть)

login as: root
root@192.168.1.3's password:
  ___                               ____  _   ____       _
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |  _ \ _ __(_)_ __ ___   ___
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | |_) | '__| | '_ ` _ \ / _ \
| |_| | | | (_| | | | | (_| |  __/ |  __/| | |  __/| |  | | | | | | |  __/
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| |_|   |_|  |_|_| |_| |_|\___|
                       |___/

Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi64
System load:   0.59 0.16 0.05   Up time:       0 min
Memory usage:  4 % of 2002MB    IP:            192.168.1.3
CPU temp:      28°C
Usage of /:    4% of 59G

Last login: Sun Apr 29 15:15:50 2018 from 192.168.1.2

root@orangepiprime:~# chmod 777 /dev/tty0
root@orangepiprime:~#

от алекса, не перезагружаясь

Код: [Выделить]

startx

(Нажмите, чтобы показать/скрыть)

login as: maxim
maxim@192.168.1.3's password:
  ___                               ____  _   ____       _
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |  _ \ _ __(_)_ __ ___   ___
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | |_) | '__| | '_ ` _ \ / _ \
| |_| | | | (_| | | | | (_| |  __/ |  __/| | |  __/| |  | | | | | | |  __/
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| |_|   |_|  |_|_| |_| |_|\___|
                       |___/

Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi64
System load:   0.02 0.08 0.04   Up time:       3 min
Memory usage:  4 % of 2002MB    IP:            192.168.1.3
CPU temp:      20°C
Usage of /:    4% of 59G

Last login: Sun Apr 29 15:06:22 2018 from 192.168.1.2

maxim@orangepiprime:~$ startx


X.Org X Server 1.19.2
Release Date: 2017-03-02
X Protocol Version 11, Revision 0
Build Operating System: Linux 4.9.0-4-arm64 aarch64 Debian
Current Operating System: Linux orangepiprime 4.14.18-sunxi64 #26 SMP Fri Feb 9 17:14:48 CET 2018 aarch64
Kernel command line: root=UUID=a2a90d4d-5aa6-4dd7-979f-cf0ff08bcda2 rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 panic=10 consoleblank=0 loglevel=1 ubootpart=089c372c-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u   cgroup_enable=memory swapaccount=1
Build Date: 16 October 2017  08:11:43AM
xorg-server 2:1.19.2-1+deb9u2 (https://www.debian.org/support)
Current version of pixman: 0.34.0
        Before reporting problems, check http://wiki.x.org
        to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
        (++) from command line, (!!) notice, (II) informational,
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/home/maxim/.local/share/xorg/Xorg.1.log", Time: Sun Apr 29 15:22:02 2018
(==) Using config directory: "/etc/X11/xorg.conf.d"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
(EE)
Fatal server error:
(EE) xf86OpenConsole: Cannot open virtual console 2 (Permission denied)
(EE)
(EE)
Please consult the The X.Org Foundation support
         at http://wiki.x.org
 for help.
(EE) Please also check the log file at "/home/maxim/.local/share/xorg/Xorg.1.log" for additional information.
(EE)
(EE) Server terminated with error (1). Closing log file.
xinit: giving up
xinit: unable to connect to X server: Connection refused
xinit: server error
maxim@orangepiprime:~$

[hesoyamatogun]

уже другая подобная ошибка. Добавляй себя в группу tty

От рута

Код: [Выделить]

useradd -G tty maximзы от рута startx должен запустится уже давно

[SimpleHosting]

уже другая подобная ошибка. Добавляй себя в группу tty

От рута

Код: [Выделить]

useradd -G tty maximзы от рута startx должен запустится уже давно

(Нажмите, чтобы показать/скрыть)

login as: root
root@192.168.1.3's password:
  ___                               ____  _   ____       _
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |  _ \ _ __(_)_ __ ___   ___
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | |_) | '__| | '_ ` _ \ / _ \
| |_| | | | (_| | | | | (_| |  __/ |  __/| | |  __/| |  | | | | | | |  __/
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| |_|   |_|  |_|_| |_| |_|\___|
                       |___/

Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi64
System load:   0.00 0.04 0.04   Up time:       14 min
Memory usage:  4 % of 2002MB    IP:            192.168.1.3
CPU temp:      17°C
Usage of /:    4% of 59G

Last login: Sun Apr 29 15:18:33 2018 from 192.168.1.2

root@orangepiprime:~# useradd -G tty maxim
useradd: user 'maxim' already exists
root@orangepiprime:~#

[hesoyamatogun]

надеюсь ты не через SSH сидишь а через клаву-мышку-hdmi?
запускай от рута startx

У теня точно такое уже было. Запустил спева от рута startx, но он запустился сразу, так как был полностью установлен. Но потом от обычного пользователя нивкакую не запусказся, везде Permission denied. Видимо где-то создался рутовский файл а обычному пользователю туда путь заказан, а иксам нужен этот файл.
Тоже копал права решил что легче будет переустанивить иксы.

[SimpleHosting]

надеюсь ты не через SSH сидишь а через клаву-мышку-hdmi?

Я подключаюсь через PuTTY, если нужно могу подключить мышку, клавиатуру, т.к. монитор у меня VGA, могу подключить через переходник.

запускай от рута startx

(Нажмите, чтобы показать/скрыть)

login as: root
root@192.168.1.3's password:
  ___                               ____  _   ____       _
 / _ \ _ __ __ _ _ __   __ _  ___  |  _ \(_) |  _ \ _ __(_)_ __ ___   ___
| | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | |_) | '__| | '_ ` _ \ / _ \
| |_| | | | (_| | | | | (_| |  __/ |  __/| | |  __/| |  | | | | | | |  __/
 \___/|_|  \__,_|_| |_|\__, |\___| |_|   |_| |_|   |_|  |_|_| |_| |_|\___|
                       |___/

Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi64
System load:   1.52 0.95 0.43   Up time:       4 min
Memory usage:  4 % of 2002MB    IP:            192.168.1.3
CPU temp:      44°C
Usage of /:    4% of 59G

[ General system configuration (beta): armbian-config ]

Last login: Sun Apr 29 15:36:14 2018 from 192.168.1.2

root@orangepiprime:~# startx


X.Org X Server 1.19.2
Release Date: 2017-03-02
X Protocol Version 11, Revision 0
Build Operating System: Linux 4.9.0-4-arm64 aarch64 Debian
Current Operating System: Linux orangepiprime 4.14.18-sunxi64 #26 SMP Fri Feb 9 17:14:48 CET 2018 aarch64
Kernel command line: root=UUID=a2a90d4d-5aa6-4dd7-979f-cf0ff08bcda2 rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 panic=10 consoleblank=0 loglevel=1 ubootpart=089c372c-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u   cgroup_enable=memory swapaccount=1
Build Date: 16 October 2017  08:11:43AM
xorg-server 2:1.19.2-1+deb9u2 (https://www.debian.org/support)
Current version of pixman: 0.34.0
        Before reporting problems, check http://wiki.x.org
        to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
        (++) from command line, (!!) notice, (II) informational,
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.1.log", Time: Sun Apr 29 15:41:17 2018
(==) Using config directory: "/etc/X11/xorg.conf.d"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
MESA-LOADER: failed to retrieve device information
gbm: failed to open any driver (search paths /usr/lib/aarch64-linux-gnu/dri:${ORIGIN}/dri:/usr/lib/dri)
gbm: Last dlopen error: /usr/lib/dri/sun4i-drm_dri.so: cannot open shared object file: No such file or directory
failed to load driver: sun4i-drm
EGL_MESA_drm_image required.

Похоже завис.

[hesoyamatogun]

Ты думал запустить иксы через по-сути матричный принтер или телеграф?
цепляй мышь, клаву, монитор через вга переходник, со звуком, колонки не забудь, блин.

[SimpleHosting]

Ты думал запустить иксы через по-сути матричный принтер или телеграф?
цепляй мышь, клаву, монитор через вга переходник, со звуком, колонки не забудь, блин.

Может не надо колонки...?

[hesoyamatogun]

А как же звук. Ну наушники можно.
Тоесть у тебя был подключен уже мониор, ты через SSH набирал команду startx и ждал что на мониторе что-то запустится?
Или у тебя вовсе не был подключен мониор и ты ждал графику в окне Kitty?
Цепляй клавиатуру и монитор, остальное не обязательно. Логинешся через эту клавиатуру и монитор и там уже запускаешь startx
Сперва от максима, потом от рута.

[SimpleHosting]

А как же звук. Ну наушники можно.
Тоесть у тебя был подключен уже мониор, ты через SSH набирал команду startx и ждал что на мониторе что-то запустится?
Или у тебя вовсе не был подключен мониор и ты ждал графику в окне Kitty?
Цепляй клавиатуру и монитор, остальное не обязательно. Логинешся через эту клавиатуру и монитор и там уже запускаешь startx
Сперва от максима, потом от рута.

У меня один монитор на апельсинку и...
Не получилось запустить иксы, шла загрузка, а потом зависла, мне некуда было вводить startx
Пользователь добавил сообщение 29 Апреля 2018, 20:14:50:Попробую залить на карту памяти Armbian_5.38_Orangepiprime_Ubuntu_xenial_next_4.14.14_desktop
Пользователь добавил сообщение 29 Апреля 2018, 21:05:47:Поставил

Код: [Выделить]

apt-get install xrdpНо подключиться не получилось.

Вернусь к той версии, с которой начал http://orangepi.org/downloadresources

кнопочки!? не так все просто.

Надеялся будет несложно.

Или расширять boot за счет 2 раздела, либо копировать содержимое boot в корневой каталог, поправить fstab...

Я вас не понимаю.

Была тема на форуме, поищите

Можете ключевые слова для поиска подсказать?

проще будет переустановить начисто

Могу и переустановить, при переустановке какие нужно нажимать кнопочки? Я при установке пользовался этой http://forum.adsbradar.ru/f25/rasshiryaem-obraz-failovoi-sistemy-na-ves-razmer-sd-karty-1408 инструкцией, а как правильно?

18 правильно

Я вас не понимаю.
Пользователь добавил сообщение 29 Апреля 2018, 21:58:02:Попробовал так:

(Нажмите, чтобы показать/скрыть)

su
df -h
Filesystem      Size  Used Avail Use% Mounted on
/dev/mmcblk0p2  3.4G  2.9G  321M  91% /
devtmpfs        986M     0  986M   0% /dev
tmpfs           995M     0  995M   0% /dev/shm
tmpfs           995M   25M  970M   3% /run
tmpfs           5.0M  4.0K  5.0M   1% /run/lock
tmpfs           995M     0  995M   0% /sys/fs/cgroup
/dev/mmcblk0p1   50M   26M   25M  52% /boot
tmpfs           199M     0  199M   0% /run/user/1000
root@Orangepi:/home/orangepi#

fdisk /dev/mmcblk0
Command (m for help): p
Disk /dev/mmcblk0: 59.6 GiB, 64021856256 bytes, 125042688 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x000ebed2

Device         Boot  Start     End Sectors  Size Id Type
/dev/mmcblk0p1       40960  143359  102400   50M  c W95 FAT32 (LBA)
/dev/mmcblk0p2      143360 7395327 7251968  3.5G 83 Linux

Command (m for help):
d
2
d
n
p
1
40960
Enter
w
reboot

и после перезагрузки не получается подключиться через PuTTY