Не определилась PCMCIA Lan Card (не решено)

[Geo]

Нужна помощь
При установке Kubuntu 8.04 на ноут не определилась PCMCIA сетевая карта SURECOM EtherPerfect-427.
В результате нет сети.
Поиск по форум и по Google ничего конкретного не дал. Все только для винды.
Куда копать дальше?

[Stiff]

Код: [Выделить]

lspci
lsusb
ifconfig -a
сюда

[Geo]

geo@george-kubuntu:~$ lspci
00:00.0 Host bridge: ALi Corporation M1621 (rev 01)
00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller (rev 01)
00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 01)
00:07.0 ISA bridge: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+]
00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c3)
00:11.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
00:13.0 CardBus bridge: O2 Micro, Inc. OZ6812 CardBus Controller (rev 05)
00:14.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/i1 (rev 5d)
geo@george-kubuntu:~$
geo@george-kubuntu:~$ lsusb
Bus 001 Device 002: ID 13fe:1d00 Kingston Technology Company Inc. DataTraveler 2.0 1GB Flash Drive
Bus 001 Device 001: ID 0000:0000
geo@george-kubuntu:~$ ifconfig -a
lo        Link encap:Локальная петля (Loopback)
          inet addr:127.0.0.1  Mask:255.0.0.0
          ВВЕРХ LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          коллизии:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

geo@george-kubuntu:~$

Не нужно видимо говорить, что под оффтопиком все определяется и работает.

[Stiff]

Только карта почему-то в списке не светится.
Она точно включена?

upd: покажи ещё lspcmcia

[Geo]

geo@george-kubuntu:~$ lspcmcia
Socket 0 Bridge:        [yenta_cardbus]         (bus ID: 0000:00:13.0)
Socket 0 Device 0:      [-- no driver --]       (bus ID: 0.0)
geo@george-kubuntu:~$

Карточка включена и при перезагрузке в винду работает в сетке нормально.
При загрузке Kubuntu - на ней на короткое время мигают светодиоды обмена (2 шт.),
после чего - мертвяк. И сетки нет.

[Stiff]

Единственное, что приходит на ум - попробовать пересобрать ядро
Отпишитесь плз у кого есть работающая pcmcia сетевуха под Linuxом

[Geo]

Еще информация:

geo@george-kubuntu:~$ pccardctl status
Socket 0:
  5.0V 16-bit PC Card
  Subdevice 0 (function 0) [unbound]
geo@george-kubuntu:~$ pccardctl config
Socket 0:
command 'config' not yet handled by pccardctl
geo@george-kubuntu:~$ pccardctl ident
Socket 0:
  product info: "TAMARACK", "Ethernet", "A", "0047433180�0"
  function: 6 (network)
geo@george-kubuntu:~$ pccardctl info
PRODID_1="TAMARACK"
PRODID_2="Ethernet"
PRODID_3="A"
PRODID_4="0047433180�0"
MANFID=0000,0000
FUNCID=6
geo@george-kubuntu:~$ pccardctl ls
Socket 0 Bridge:        [yenta_cardbus]         (bus ID: 0000:00:13.0)
Socket 0 Device 0:      [-- no driver --]       (bus ID: 0.0)

Судя по приведенному Kubuntu неправильно определило тип карты, в результате не может через нее работать.
Отсюда вопросы:
1. Как вычислить модуль (драйвер) который подгружается, каким скриптом, и как заменить его на правильный?
2. Есть ли правильный модуль на эту карту SURECOM EtherPerfect-427 ?
3. Усли такого нет, какую карту купить, чтобы ее поддерживала Ubuntu/Kubuntu?

[Stiff]

Можно ещё dmesg посмотреть

[Geo]

geo@george-kubuntu:~$ dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.24-19-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Wed Jun 18 14:43:41 UTC 2008 (Ubuntu 2.6.24-19.34-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000277f0000 (usable)
[    0.000000]  BIOS-e820: 00000000277f0000 - 00000000277f8000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000277f8000 - 0000000027800000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 631MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 161776) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   161776
[    0.000000]   HighMem    161776 ->   161776
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   161776
[    0.000000] On node 0 totalpages: 161776
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1231 pages used for memmap
[    0.000000]   Normal zone: 156449 pages, LIFO batch:31
[    0.000000]   HighMem zone: 0 pages used for memmap
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP signature @ 0xC00FE030 checksum 0
[    0.000000] ACPI: RSDP 000FE030, 0014 (r0 Acer  )
[    0.000000] ACPI: RSDT 277F0000, 002C (r1 Acer   FALCON2M        1 Acer        0)
[    0.000000] ACPI: FACP 277F0054, 0074 (r1 Acer   FALCON2M        1 Acer        0)
[    0.000000] ACPI: DSDT 277F00CC, 471E (r1   Acer FALCON2M        1 MSFT  100000D)
[    0.000000] ACPI: FACS 277F8000, 0040
[    0.000000] ACPI: BOOT 277F002C, 0028 (r1 Acer   FALCON2M        1 Acer        0)
[    0.000000] ACPI: DMI detected: Acer
[    0.000000] ACPI: PM-Timer IO Port: 0xf108
[    0.000000] Allocating PCI resources starting at 30000000 (gap: 27800000:d87f0000)
[    0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[    0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 160513
[    0.000000] Kernel command line: root=UUID=27de3e39-7293-40bb-9d7b-e414116c3d18 ro quiet nosplash vga=791
[    0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[    0.000000] mapped APIC to ffffb000 (014fe000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 797.013 MHz processor.
[   15.871002] Console: colour dummy device 80x25
[   15.871019] console [tty0] enabled
[   15.875158] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   15.883685] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   15.997831] Memory: 628740k/647104k available (2177k kernel code, 17688k reserved, 1006k data, 368k init, 0k highmem)
[   15.997856] virtual kernel memory layout:
[   15.997859]     fixmap  : 0xfff4b000 - 0xfffff000   ( 720 kB)
[   15.997863]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   15.997866]     vmalloc : 0xe8000000 - 0xff7fe000   ( 375 MB)
[   15.997870]     lowmem  : 0xc0000000 - 0xe77f0000   ( 631 MB)
[   15.997873]       .init : 0xc0421000 - 0xc047d000   ( 368 kB)
[   15.997877]       .data : 0xc0320434 - 0xc041bdc4   (1006 kB)
[   15.997880]       .text : 0xc0100000 - 0xc0320434   (2177 kB)
[   15.997890] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   15.998038] SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[   16.078049] Calibrating delay using timer specific routine.. 1595.67 BogoMIPS (lpj=3191350)
[   16.078157] Security Framework initialized
[   16.078200] SELinux:  Disabled at boot.
[   16.078253] AppArmor: AppArmor initialized
[   16.078268] Failure registering capabilities with primary security module.
[   16.078296] Mount-cache hash table entries: 512
[   16.078845] Initializing cgroup subsys ns
[   16.078869] Initializing cgroup subsys cpuacct
[   16.078904] CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[   16.078938] CPU: L1 I cache: 16K, L1 D cache: 16K
[   16.078945] CPU: L2 cache: 128K
[   16.078958] CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 00000000
[   16.078998] Compat vDSO mapped to ffffe000.
[   16.079056] Checking 'hlt' instruction... OK.
[   16.094854] SMP alternatives: switching to UP code
[   16.098924] Freeing SMP alternatives: 11k freed
[   16.099523] Early unpacking initramfs... done
[   17.307199] ACPI: Core revision 20070126
[   17.307639] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   17.312008] ACPI: setting ELCR to 0200 (from 0e00)
[   17.315628] CPU0: Intel Celeron (Coppermine) stepping 0a
[   17.315655] SMP motherboard not detected.
[   17.315664] Local APIC not detected. Using dummy APIC emulation.
[   17.315906] Brought up 1 CPUs
[   17.316007] CPU0 attaching sched-domain:
[   17.316018]  domain 0: span 01
[   17.316023]   groups: 01
[   17.317135] net_namespace: 64 bytes
[   17.317176] Booting paravirtualized kernel on bare hardware
[   17.319237] Time: 15:10:20  Date: 07/06/08
[   17.319413] NET: Registered protocol family 16
[   17.320833] EISA bus registered
[   17.320898] ACPI: bus type pci registered
[   17.357810] PCI: PCI BIOS revision 2.10 entry at 0xf0200, last bus=1
[   17.357824] PCI: Using configuration type 1
[   17.357861] Setting up standard PCI resources
[   17.365124] ACPI: EC: Look up EC in DSDT
[   17.370573] ACPI: Interpreter enabled
[   17.370599] ACPI: (supports S0 S1 S4 S5)
[   17.370640] ACPI: Using PIC for interrupt routing
[   17.401883] ACPI: EC: GPE = 0x22, I/O: command/status = 0x66, data = 0x62
[   17.401902] ACPI: EC: driver started in poll mode
[   17.402240] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   17.402940] PCI quirk: region f100-f13f claimed by ali7101 ACPI
[   17.402950] PCI quirk: region f140-f15f claimed by ali7101 SMB
[   17.403748] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   17.408838] ACPI: PCI Interrupt Link [PILA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[   17.409283] ACPI: PCI Interrupt Link [PILB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[   17.409807] ACPI: PCI Interrupt Link [PILC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[   17.410236] ACPI: PCI Interrupt Link [PILD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[   17.410640] ACPI: PCI Interrupt Link [PILE] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[   17.411045] ACPI: PCI Interrupt Link [PILF] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[   17.411467] ACPI: PCI Interrupt Link [PILG] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[   17.411886] ACPI: PCI Interrupt Link [PILH] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[   17.412306] ACPI: PCI Interrupt Link [PILI] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[   17.413186] Linux Plug and Play Support v0.97 (c) Adam Belay
[   17.413587] pnp: PnP ACPI init
[   17.413660] ACPI: bus type pnp registered
[   17.439764] pnp: PnP ACPI: found 11 devices
[   17.439785] ACPI: ACPI bus type pnp unregistered
[   17.439799] PnPBIOS: Disabled by ACPI PNP
[   17.441795] PCI: Using ACPI for IRQ routing
[   17.441813] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   17.473364] NET: Registered protocol family 8
[   17.473378] NET: Registered protocol family 20
[   17.473889] AppArmor: AppArmor Filesystem Enabled
[   17.477328] Time: tsc clocksource has been installed.
[   17.485700] system 00:0a: ioport range 0xf100-0xf13f has been reserved
[   17.485712] system 00:0a: ioport range 0xf140-0xf15f has been reserved
[   17.485719] system 00:0a: ioport range 0x1060-0x106f has been reserved
[   17.485728] system 00:0a: ioport range 0x40b-0x40b has been reserved
[   17.485736] system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
[   17.485754] system 00:0a: iomem range 0xfffc0000-0xfffeffff has been reserved
[   17.485762] system 00:0a: iomem range 0x0-0x9ff could not be reserved
[   17.485769] system 00:0a: iomem range 0xf00-0xfff could not be reserved
[   17.485777] system 00:0a: iomem range 0xffff0000-0xffffffff could not be reserved
[   17.485785] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[   17.485793] system 00:0a: iomem range 0x100000-0xffffff could not be reserved
[   17.485801] system 00:0a: iomem range 0x1000000-0x277fffff could not be reserved
[   17.518798] PCI: Bridge: 0000:00:01.0
[   17.518815]   IO window: disabled.
[   17.518825]   MEM window: 80100000-818fffff
[   17.518832]   PREFETCH window: disabled.
[   17.518842] PCI: Bus 2, cardbus bridge: 0000:00:13.0
[   17.518849]   IO window: 00001400-000014ff
[   17.518856]   IO window: 00001800-000018ff
[   17.518863]   PREFETCH window: 30000000-33ffffff
[   17.518870]   MEM window: 34000000-37ffffff
[   17.518896] PCI: Setting latency timer of device 0000:00:01.0 to 64
[   17.519862] ACPI: PCI Interrupt Link [PILB] enabled at IRQ 11
[   17.519878] PCI: setting IRQ 11 as level-triggered
[   17.519886] ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [PILB] -> GSI 11 (level, low) -> IRQ 11
[   17.519958] NET: Registered protocol family 2
[   17.557679] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   17.559549] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[   17.572805] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   17.579553] TCP: Hash tables configured (established 131072 bind 65536)
[   17.579579] TCP reno registered
[   17.590134] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
[   18.407957]  it is
[   19.685139] Freeing initrd memory: 7690k freed
[   19.686412] Simple Boot Flag at 0x6e set to 0x1
[   19.688799] audit: initializing netlink socket (disabled)
[   19.688878] audit(1215357021.696:1): initialized
[   19.702402] VFS: Disk quotas dquot_6.5.1
[   19.702936] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   19.703875] io scheduler noop registered
[   19.703888] io scheduler anticipatory registered
[   19.703894] io scheduler deadline registered
[   19.704010] io scheduler cfq registered (default)
[   19.704067] Activating ISA DMA hang workarounds.
[   19.704124] Boot video device is 0000:01:00.0
[   19.705919] isapnp: Scanning for PnP cards...
[   20.060597] isapnp: No Plug & Play device found
[   20.408430] Real Time Clock Driver v1.12ac
[   20.408998] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   20.410407] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   20.414490] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[   20.420201] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   20.420604] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[   20.421210] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[   20.424195] serio: i8042 KBD port at 0x60,0x64 irq 1
[   20.424225] serio: i8042 AUX port at 0x60,0x64 irq 12
[   20.432036] mice: PS/2 mouse device common for all mice
[   20.432920] EISA: Probing bus 0 at eisa.0
[   20.432949] Cannot allocate resource for EISA slot 1
[   20.432991] Cannot allocate resource for EISA slot 7
[   20.432997] Cannot allocate resource for EISA slot 8
[   20.433002] EISA: Detected 0 cards.
[   20.433014] cpuidle: using governor ladder
[   20.433020] cpuidle: using governor menu
[   20.433900] NET: Registered protocol family 1
[   20.434064] Using IPI No-Shortcut mode
[   20.434255] registered taskstats version 1
[   20.434534]   Magic number: 0:662:183
[   20.434669]   hash matches device ttyr9
[   20.434899] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[   20.434905] EDD information not available.
[   20.437762] Freeing unused kernel memory: 368k freed
[   20.463769] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[   21.033109] vesafb: framebuffer at 0x80800000, mapped to 0xe8080000, using 3072k, total 8192k
[   21.033128] vesafb: mode is 1024x768x16, linelength=2048, pages=4
[   21.033135] vesafb: protected mode interface info at c000:7640
[   21.033143] vesafb: pmi: set display start = c00c7650, set palette = c00c76b3
[   21.033149] vesafb: scrolling: redraw
[   21.033158] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[   21.034139] Console: switching to colour frame buffer device 128x48
[   21.098641] fb0: VESA VGA frame buffer device
[   21.692760] fuse init (API version 7.9)
[   21.791092] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[   21.803601] ACPI: Thermal Zone [THR2] (46 C)
[   24.471780] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   24.471812] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[   24.538894] ALI15X3: IDE controller (0x10b9:0x5229 rev 0xc3) at  PCI slot 0000:00:10.0
[   24.538948] ACPI: Unable to derive IRQ for device 0000:00:10.0
[   24.538973] ALI15X3: not 100% native mode: will probe irqs later
[   24.539024]     ide0: BM-DMA at 0x7050-0x7057, BIOS settings: hda:DMA, hdb:pio
[   24.539064]     ide1: BM-DMA at 0x7058-0x705f, BIOS settings: hdc:DMA, hdd:pio
[   24.539100] Probing IDE interface ide0...
[   24.700907] usbcore: registered new interface driver usbfs
[   24.701030] usbcore: registered new interface driver hub
[   24.714784] usbcore: registered new device driver usb
[   24.740643] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[   24.822304] Floppy drive(s): fd0 is 1.44M
[   24.839245] FDC 0 is a post-1991 82077
[   25.560234] hda: WDC WD400VE-75HDT1, ATA DISK drive
[   25.560443] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[   25.560541] hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
[   25.560550] hda: UDMA/33 mode selected
[   25.560733] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[   25.560927] Probing IDE interface ide1...
[   26.631460] hdc: TOSHIBA CD-ROM XM-7002Bc, ATAPI CD/DVD-ROM drive
[   26.631631] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[   26.631765] hdc: UDMA/33 mode selected
[   26.632013] ide1 at 0x170-0x177,0x376 on irq 15
[   26.641320] ACPI: PCI Interrupt Link [PILI] enabled at IRQ 11
[   26.641354] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [PILI] -> GSI 11 (level, low) -> IRQ 11
[   26.641419] ohci_hcd 0000:00:14.0: OHCI Host Controller
[   26.642691] ohci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[   26.642766] ohci_hcd 0000:00:14.0: irq 11, io mem 0x81c00000
[   26.687326] SCSI subsystem initialized
[   26.732665] usb usb1: configuration #1 chosen from 1 choice
[   26.732770] hub 1-0:1.0: USB hub found
[   26.732802] hub 1-0:1.0: 2 ports detected
[   26.783302] libata version 3.00 loaded.
[   28.052552] hda: max request size: 128KiB
[   28.444303] hda: 78140160 sectors (40007 MB) w/8192KiB Cache, CHS=65535/16/63
[   28.444444] hda: cache flushes supported
[   28.444642]  hda: hda1 hda2 < hda5 hda6 hda7 >
[   28.527676] hdc: ATAPI 24X CD-ROM drive, 128kB Cache
[   28.527703] Uniform CD-ROM driver Revision: 3.20
[   29.403703] Attempting manual resume
[   29.403724] swsusp: Resume From Partition 3:7
[   29.403729] PM: Checking swsusp image.
[   29.404230] PM: Resume from disk failed.
[   29.518591] kjournald starting.  Commit interval 5 seconds
[   29.518668] EXT3-fs: mounted filesystem with ordered data mode.
[   41.225499] Linux agpgart interface v0.102
[   41.325513] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   41.650773] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   41.721316] agpgart: Detected ALi M1632 chipset
[   41.728518] agpgart: AGP aperture is 64M @ 0xe0000000
[   41.801212] Yenta: CardBus bridge found at 0000:00:13.0 [1025:1019]
[   41.801252] Yenta O2: res at 0x94/0xD4: 00/ea
[   41.801258] Yenta O2: old bridge, disabling read prefetch/write burst
[   41.929655] Yenta: ISA IRQ mask 0x0438, PCI irq 11
[   41.929674] Socket status: 30000411
[   42.245058] input: PC Speaker as /devices/platform/pcspkr/input/input2
[   42.720255] pccard: PCMCIA card inserted into slot 0
[   43.196805] input: Power Button (FF) as /devices/virtual/input/input3
[   43.211915] ACPI: Power Button (FF) [PWRF]
[   43.212477] input: Sleep Button (CM) as /devices/virtual/input/input4
[   43.223909] ACPI: Sleep Button (CM) [SLPB]
[   43.224494] input: Lid Switch as /devices/virtual/input/input5
[   43.224827] ACPI: Lid Switch [liD]
[   43.506290] ACPI: AC Adapter [AC] (on-line)
[   43.794494] ACPI: Battery Slot [BAT0] (battery present)
[   47.905710] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6
[   49.552327] parport_pc 00:07: reported by Plug and Play ACPI
[   49.552407] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[   49.617196] ACPI: WMI-Acer: Mapper loaded
[   49.672613] acer_acpi: Acer Laptop ACPI Extras version 0.11.1
[   49.672673] acer_acpi: No or unsupported WMI interface, unable to load.
[   50.732200] ACPI: PCI Interrupt Link [PILH] enabled at IRQ 10
[   50.732220] PCI: setting IRQ 10 as level-triggered
[   50.732228] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [PILH] -> GSI 10 (level, low) -> IRQ 10
[   55.427849] cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f
[   55.432020] cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f
[   55.433722] cs: IO port probe 0x820-0x8ff: clean.
[   55.435252] cs: IO port probe 0xc00-0xcf7: clean.
[   55.437516] cs: IO port probe 0xa00-0xaff: clean.
[   55.439267] cs: memory probe 0xa0000000-0xa0ffffff: clean.
[   55.504452] pcmcia: registering new device pcmcia0.0
[   58.478211] loop: module loaded
[   58.566954] lp0: using parport0 (interrupt-driven).
[   58.858109] Adding 1124508k swap on /dev/hda7.  Priority:-1 extents:1 across:1124508k
[   59.471037] EXT3 FS on hda6, internal journal
[   59.860387] device-mapper: uevent: version 1.0.3
[   59.860517] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
[   62.459227] ip_tables: (C) 2000-2006 Netfilter Core Team
[   65.519371] No dock devices found.
[   69.468884] apm: BIOS version 1.2 Flags 0x0f (Driver version 1.16ac)
[   69.468912] apm: overridden by ACPI.
[   69.926310] ppdev: user-space parallel port driver
[   70.203028] audit(1215346273.080:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=4957 profile="/usr/sbin/cupsd" namespace="default"
[   81.724366] Bluetooth: Core ver 2.11
[   81.727658] NET: Registered protocol family 31
[   81.727684] Bluetooth: HCI device and connection manager initialized
[   81.727699] Bluetooth: HCI socket layer initialized
[   81.812957] Bluetooth: L2CAP ver 2.9
[   81.812983] Bluetooth: L2CAP socket layer initialized
[   81.977149] Bluetooth: RFCOMM socket layer initialized
[   81.977246] Bluetooth: RFCOMM TTY layer initialized
[   81.977253] Bluetooth: RFCOMM ver 1.8
[  158.273912] usb 1-2: new full speed USB device using ohci_hcd and address 2
[  158.490236] usb 1-2: configuration #1 chosen from 1 choice
[  159.132069] usbcore: registered new interface driver libusual
[  159.290500] Initializing USB Mass Storage driver...
[  159.304447] scsi0 : SCSI emulation for USB Mass Storage devices
[  159.313749] usbcore: registered new interface driver usb-storage
[  159.314775] USB Mass Storage support registered.
[  159.321708] usb-storage: device found at 2
[  159.321731] usb-storage: waiting for device to settle before scanning
[  164.319600] usb-storage: device scan complete
[  164.326604] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[  164.448743] Driver 'sd' needs updating - please use bus_type methods
[  165.868978] sd 0:0:0:0: [sda] 1953792 512-byte hardware sectors (1000 MB)
[  165.878410] sd 0:0:0:0: [sda] Write Protect is off
[  165.878443] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[  165.878453] sd 0:0:0:0: [sda] Assuming drive cache: write through
[  165.905273] sd 0:0:0:0: [sda] 1953792 512-byte hardware sectors (1000 MB)
[  165.912348] sd 0:0:0:0: [sda] Write Protect is off
[  165.912387] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[  165.912397] sd 0:0:0:0: [sda] Assuming drive cache: write through
[  165.912433]  sda: sda1
[  165.922715] sd 0:0:0:0: [sda] Attached SCSI removable disk
[  165.974323] sd 0:0:0:0: Attached scsi generic sg0 type 0
[  501.534322] usb 1-2: USB disconnect, address 2
[ 8783.219759] usb 1-2: new full speed USB device using ohci_hcd and address 3
[ 8783.435857] usb 1-2: configuration #1 chosen from 1 choice
[ 8783.474984] scsi1 : SCSI emulation for USB Mass Storage devices
[ 8783.476958] usb-storage: device found at 3
[ 8783.476979] usb-storage: waiting for device to settle before scanning
[ 8788.473912] usb-storage: device scan complete
[ 8788.480905] scsi 1:0:0:0: Direct-Access     Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 8788.752701] sd 1:0:0:0: [sda] 1953792 512-byte hardware sectors (1000 MB)
[ 8788.759573] sd 1:0:0:0: [sda] Write Protect is off
[ 8788.759603] sd 1:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 8788.759611] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 8788.786512] sd 1:0:0:0: [sda] 1953792 512-byte hardware sectors (1000 MB)
[ 8788.793561] sd 1:0:0:0: [sda] Write Protect is off
[ 8788.793589] sd 1:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 8788.793598] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 8788.793633]  sda: sda1
[ 8788.804056] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 8788.804224] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 8902.119649] usb 1-2: USB disconnect, address 3
[16986.203359] usb 1-2: new full speed USB device using ohci_hcd and address 4
[16986.419648] usb 1-2: configuration #1 chosen from 1 choice
[16986.455278] scsi2 : SCSI emulation for USB Mass Storage devices
[16986.464925] usb-storage: device found at 4
[16986.464952] usb-storage: waiting for device to settle before scanning
[16991.461644] usb-storage: device scan complete
[16991.468637] scsi 2:0:0:0: Direct-Access     Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[16991.739323] sd 2:0:0:0: [sda] 1953792 512-byte hardware sectors (1000 MB)
[16991.746341] sd 2:0:0:0: [sda] Write Protect is off
[16991.746371] sd 2:0:0:0: [sda] Mode Sense: 23 00 00 00
[16991.746380] sd 2:0:0:0: [sda] Assuming drive cache: write through
[16991.772265] sd 2:0:0:0: [sda] 1953792 512-byte hardware sectors (1000 MB)
[16991.779316] sd 2:0:0:0: [sda] Write Protect is off
[16991.779346] sd 2:0:0:0: [sda] Mode Sense: 23 00 00 00
[16991.779355] sd 2:0:0:0: [sda] Assuming drive cache: write through
[16991.779387]  sda: sda1
[16991.789729] sd 2:0:0:0: [sda] Attached SCSI removable disk
[16991.789896] sd 2:0:0:0: Attached scsi generic sg0 type 0
[17112.507327] usb 1-2: USB disconnect, address 4
geo@george-kubuntu:~$

Сильно большой, однако...

[Geo]

Неужели нет никого, кто бы сталкивался с ethernet card, втыкаемых в слот PCMCIA?

P.S. Попробовал PuppiRus, загрузка с ливсд.
Все отлично определилось и работает.
Так что могли дистрописатели так сломать в Ubuntu, что она определяет оборудование
много хуже, чем облегченные дистры вроде Пуппи?

[chkur]

Присоединяюсь к вопросу. Хотя бы ткните в мануал настройки pcmcia-карточек.