smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org=== START OF INFORMATION SECTION ===
Device Model: HGST HTE721010A9E630
Serial Number: JR10034M1LGMRK
LU WWN Device Id: 5 000cca 8a8d67d20
Firmware Version: JB0OA3M0
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Wed Feb 14 10:03:40 2018 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 45) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 170) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 066 066 062 Pre-fail Always - 386073418
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 120 120 033 Pre-fail Always - 2
4 Start_Stop_Count 0x0012 099 099 000 Old_age Always - 1978
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 094 094 000 Old_age Always - 2987
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1966
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 139
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 2041
194 Temperature_Celsius 0x0002 162 162 000 Old_age Always - 37 (Min/Max 15/52)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2707
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 56
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 5683 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 5683 occurred at disk power-on lifetime: 2982 hours (124 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 58 08 ff c9 08 Error: UNC 88 sectors at LBA = 0x08c9ff08 = 147455752
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 60 fe c9 e0 00 01:38:40.379 READ DMA EXT
ef 10 02 00 00 00 a0 00 01:38:40.379 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 01:38:40.378 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 01:38:40.375 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 01:38:40.375 SET FEATURES [Set transfer mode]
Error 5682 occurred at disk power-on lifetime: 2982 hours (124 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 60 00 f6 c9 08 Error: UNC 96 sectors at LBA = 0x08c9f600 = 147453440
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 60 f5 c9 e0 00 01:31:13.841 READ DMA EXT
ef 10 02 00 00 00 a0 00 01:31:13.841 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 01:31:13.841 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 01:31:13.838 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 01:31:13.837 SET FEATURES [Set transfer mode]
Error 5681 occurred at disk power-on lifetime: 2982 hours (124 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 78 e8 e9 c9 08 Error: UNC 120 sectors at LBA = 0x08c9e9e8 = 147450344
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 60 e9 c9 e0 00 01:25:29.016 READ DMA EXT
25 00 00 60 e8 c9 e0 00 01:25:06.780 READ DMA EXT
25 00 06 5a e7 c9 e0 00 01:25:06.780 READ DMA EXT
25 00 01 59 e7 c9 e0 00 01:25:06.780 READ DMA EXT
25 00 01 58 e7 c9 e0 00 01:25:05.722 READ DMA EXT
Error 5680 occurred at disk power-on lifetime: 2982 hours (124 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 38 28 e5 c9 08 Error: UNC 56 sectors at LBA = 0x08c9e528 = 147449128
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 60 e4 c9 e0 00 01:16:00.610 READ DMA EXT
ef 10 02 00 00 00 a0 00 01:16:00.610 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 01:16:00.610 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 01:16:00.606 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 01:16:00.606 SET FEATURES [Set transfer mode]
Error 5679 occurred at disk power-on lifetime: 2982 hours (124 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 c8 98 cc c9 08 Error: UNC 200 sectors at LBA = 0x08c9cc98 = 147442840
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 60 cc c9 e0 00 00:57:12.042 READ DMA EXT
ef 10 02 00 00 00 a0 00 00:57:12.041 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 00:57:12.041 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:57:12.038 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 00:57:12.038 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute dela
Тема: Не монтируется локальный жёский диск (Прочитано 2150 раз)
