Ubuntu 9.04 AR9285 Раз в 5 -10 минут падает Wi-Fi
Затем соединение можно восстановить только включением выключением сети на ноутбуке(ASUS K40AB)
Шифрование WPA-PSK
А еще глючи с отображение уровня сигнала. До антенны роутера 4 мет ра прямой видимости и комп показывает 20% на соседнем ноутбуке все отлично работает.
04:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
[ 11.407179] ath9k 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 11.407190] ath9k 0000:04:00.0: setting latency timer to 64
[ 11.457665] phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 11.501859] cfg80211: Regulatory domain changed to country: US
[ 11.501863] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 11.501865] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 11.501867] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 11.501869] (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.501871] (5490000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.501873] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 11.896347] phy0: Atheros AR9285 MAC/BB Rev:2 AR5133 RF Rev:e0: mem=0xffffc200101c0000, irq=18
[ 11.896477] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 11.896495] ACPI: I/O resource piix4_smbus [0xb00-0xb07] conflicts with ACPI region SMR1 [0xb00-0xb0f]
[ 11.896496] ACPI: Device needs an ACPI driver
[ 11.896507] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 11.896589] cfg80211: Calling CRDA for country: RU
[ 11.901515] cfg80211: Regulatory domain changed to country: RU
[ 11.901518] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 11.901521] (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 11.994727] uvcvideo: Found UVC 1.00 device CNF7129 (04f2:b071)
[ 11.996267] input: CNF7129 as /devices/pci0000:00/0000:00:13.2/usb2/2-3/2-3:1.0/input/input9
[ 12.013219] usbcore: registered new interface driver uvcvideo
[ 12.013242] USB Video Class driver (v0.1.0)
[ 12.052782] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 12.104243] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 12.338872] lp: driver loaded but no devices found
[ 12.472488] Adding 8193108k swap on /dev/sda5. Priority:-1 extents:1 across:8193108k
[ 13.026228] EXT3 FS on sda1, internal journal
[ 13.137064] input: ImPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio4/input/input10
[ 15.386644] type=1505 audit(1257489239.434:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2341
[ 15.433677] type=1505 audit(1257489239.482:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2345
[ 15.433837] type=1505 audit(1257489239.482:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2345
[ 15.433886] type=1505 audit(1257489239.482:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2345
[ 15.433926] type=1505 audit(1257489239.482:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2345
[ 15.563878] type=1505 audit(1257489239.610:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2350
[ 15.564080] type=1505 audit(1257489239.610:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2350
[ 15.595346] type=1505 audit(1257489239.642:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2354
[ 23.344836] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 23.344839] vboxdrv: Successfully done.
[ 23.344841] vboxdrv: Found 2 processor cores.
[ 23.344902] VBoxDrv: dbg - g_abExecMemory=ffffffffa0310b40
[ 23.344960] vboxdrv: fAsync=1 offMin=0xf76a9d6 offMax=0xf76a9d6
[ 23.345015] vboxdrv: TSC mode is 'asynchronous', kernel timer mode is 'normal'.
[ 23.345017] vboxdrv: Successfully loaded version 2.1.4_OSE (interface 0x000a0009).
[ 23.552669] VBoxNetFlt: dbg - g_abExecMemory=ffffffffa04af980
[ 24.667870] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 24.667873] Bluetooth: BNEP filters: protocol multicast
[ 24.685547] Bridge firewalling registered
[ 26.385082] pci 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 26.619938] [drm] Initialized drm 1.1.0 20060810
[ 26.747452] pci 0000:02:00.0: enabling device (0000 -> 0003)
[ 26.747461] pci 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 26.747467] pci 0000:02:00.0: setting latency timer to 64
[ 26.747625] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[ 26.747693] pci 0000:01:05.0: setting latency timer to 64
[ 26.747763] [drm] Initialized radeon 1.29.0 20080528 on minor 1
[ 26.819151] ppdev: user-space parallel port driver
[ 27.680450] [drm] Setting GART location based on new memory map
[ 27.695939] [drm] Loading RS780 CP Microcode
[ 27.697282] [drm] Loading RS780 PFP Microcode
[ 27.712349] [drm] Resetting GPU
[ 27.712407] [drm] writeback test succeeded in 1 usecs
[ 30.951406] r8169: eth0: link down
[ 30.952256] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 30.986982] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 31.861678] wlan0: direct probe to AP ffff8800378feac0 try 1
[ 32.064061] wlan0: direct probe to AP ffff8800378feac0 try 2
[ 32.260058] wlan0: direct probe to AP ffff8800378feac0 try 3
[ 32.460041] wlan0: direct probe to AP ffff8800378feac0 timed out
[ 52.804016] hda_intel: azx_get_response timeout, switching to polling mode: last cmd=0x01df0100
[ 53.808014] hda_intel: azx_get_response timeout, switching to single_cmd mode: last cmd=0x01df0100
[ 121.865349] wlan0: direct probe to AP ffff8800378feac0 try 1
[ 132.733526] wlan0: authenticate with AP ffff8800378feac0
[ 132.735634] wlan0: authenticated
[ 132.735650] wlan0: associate with AP ffff8800378feac0
[ 132.739518] wlan0: RX AssocResp from ffff8800ae52c04a (capab=0x411 status=0 aid=3)
[ 132.739527] wlan0: associated
[ 132.744851] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 142.749034] wlan0: no IPv6 routers present
[ 481.241808] wlan0 direct probe responded
[ 481.241823] wlan0: authenticate with AP ffff8800378feac0
[ 481.243949] wlan0: authenticated
[ 481.243956] wlan0: associate with AP ffff8800378feac0
[ 481.247343] wlan0: RX ReassocResp from ffff8800ae52004a (capab=0x411 status=0 aid=3)
[ 481.247351] wlan0: associated
[ 489.252273] wlan0: deauthenticated (Reason: 15)
[ 490.252159] wlan0: direct probe to AP ffff8800378feac0 try 1
[ 490.255642] wlan0 direct probe responded
[ 490.255651] wlan0: authenticate with AP ffff8800378feac0
[ 490.258219] wlan0: authenticated
[ 490.258227] wlan0: associate with AP ffff8800378feac0
[ 490.260935] wlan0: RX ReassocResp from ffff8800ae86804a (capab=0x411 status=0 aid=3)
[ 490.260944] wlan0: associated
[ 521.817973] UDF-fs: No VRS found
[ 521.877107] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 521.914161] ISO 9660 Extensions: RRIP_1991A
[ 674.837072] wlan0: beacon loss from AP ffff8800378feac0 - sending probe request
[ 676.837044] wlan0: no probe response from AP ffff8800378feac0 - disassociating
[ 788.884130] wlan0: deauthenticating by local choice (reason=3)
[ 791.592493] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 802.524143] wlan0: authenticate with AP ffff8800378feac0
[ 802.720041] wlan0: authenticate with AP ffff8800378feac0
[ 802.722122] wlan0: authenticated
[ 802.722131] wlan0: associate with AP ffff8800378feac0
[ 802.724793] wlan0: RX AssocResp from ffff88009f56804a (capab=0x411 status=0 aid=3)
[ 802.724802] wlan0: associated
[ 802.730214] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 812.796028] wlan0: no IPv6 routers present
[ 835.768083] wlan0: beacon loss from AP ffff8800378feac0 - sending probe request
[ 837.768052] wlan0: no probe response from AP ffff8800378feac0 - disassociating
[ 1031.645059] wlan0: deauthenticating by local choice (reason=3)
[ 1120.940581] r8169: eth0: link down
[ 1120.943608] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1120.984878] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1131.941376] wlan0: authenticate with AP ffff8800378feac0
[ 1131.943487] wlan0: authenticated
[ 1131.943502] wlan0: associate with AP ffff8800378feac0
[ 1131.946111] wlan0: RX AssocResp from ffff88009ad2e04a (capab=0x411 status=0 aid=3)
[ 1131.946121] wlan0: associated
[ 1131.950216] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1142.161027] wlan0: no IPv6 routers present
[ 1195.821071] wlan0: beacon loss from AP ffff8800378feac0 - sending probe request
[ 1197.820499] wlan0: no probe response from AP ffff8800378feac0 - disassociating
[ 1198.849944] wlan0: authenticate with AP ffff8800378feac0
[ 1198.860455] wlan0: authenticate with AP ffff8800378feac0
[ 1198.866996] wlan0: authenticated
[ 1198.867005] wlan0: associate with AP ffff8800378feac0
[ 1198.870450] wlan0: RX ReassocResp from ffff88008a54204a (capab=0x411 status=0 aid=3)
[ 1198.870460] wlan0: associated
[ 1344.268050] wlan0: beacon loss from AP ffff8800378feac0 - sending probe request
[ 1346.268073] wlan0: no probe response from AP ffff8800378feac0 - disassociating
[ 1475.884626] r8169: eth0: link down
[ 1475.887750] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1475.933857] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1477.682024] wlan0: direct probe to AP ffff8800378feac0 try 1
[ 1477.884088] wlan0: direct probe to AP ffff8800378feac0 try 2
[ 1478.081724] wlan0: direct probe to AP ffff8800378feac0 try 3
[ 1478.280090] wlan0: direct probe to AP ffff8800378feac0 timed out
[ 1486.875190] wlan0: authenticate with AP ffff8800378feac0
[ 1486.878842] wlan0 direct probe responded
[ 1486.878857] wlan0: authenticate with AP ffff8800378feac0
[ 1486.935585] wlan0: authenticated
[ 1486.935599] wlan0: associate with AP ffff8800378feac0
[ 1486.938917] wlan0: RX AssocResp from ffff8800ae87604a (capab=0x411 status=0 aid=3)
[ 1486.938927] wlan0: associated
[ 1486.943460] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1490.960090] wlan0: beacon loss from AP ffff8800378feac0 - sending probe request
[ 1492.961085] wlan0: no probe response from AP ffff8800378feac0 - disassociating
[ 1497.445057] wlan0: no IPv6 routers present
[ 1602.827669] r8169: eth0: link down
[ 1602.830769] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1602.880815] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1604.678865] wlan0: direct probe to AP ffff8800378feac0 try 1
[ 1604.877057] wlan0: direct probe to AP ffff8800378feac0 try 2
[ 1605.080095] wlan0: direct probe to AP ffff8800378feac0 try 3
[ 1605.280061] wlan0: direct probe to AP ffff8800378feac0 timed out
[ 1685.217865] wlan0: authenticate with AP ffff8800378feac0
[ 1685.219975] wlan0: authenticated
[ 1685.219983] wlan0: associate with AP ffff8800378feac0
[ 1685.222633] wlan0: RX AssocResp from ffff8800a198204a (capab=0x411 status=0 aid=3)
[ 1685.222645] wlan0: associated
[ 1685.228650] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready