smartctl 5.40 2010-03-16 r3077 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen,
http://smartmontools.sourceforge.net=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA family
Device Model: WDC WD1600BEVT-75ZCT0
Serial Number: WD-WXE308AE3602
Firmware Version: 11.01A11
User Capacity: 160 041 885 696 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Oct 21 16:37:15 2010 VOLST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (5400) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 66) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 20
3 Spin_Up_Time 0x0027 158 158 021 Pre-fail Always - 1058
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1315
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 8551
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1299
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 76
193 Load_Cycle_Count 0x0032 183 183 000 Old_age Always - 52349
194 Temperature_Celsius 0x0022 096 089 000 Old_age Always - 47
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 182 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 1
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 160 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 160 occurred at disk power-on lifetime: 8546 hours (356 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 78 d2 8f 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 00 d2 8f 09 08 16:16:07.782 READ FPDMA QUEUED
ef 10 02 00 00 00 00 08 16:16:07.782 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 16:16:07.782 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 16:16:07.781 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 16:16:07.781 SET FEATURES [Set transfer mode]
Error 159 occurred at disk power-on lifetime: 8546 hours (356 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 78 d2 8f 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 00 d2 8f 09 08 16:16:04.722 READ FPDMA QUEUED
ef 10 02 00 00 00 00 08 16:16:04.722 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 16:16:04.722 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 16:16:04.721 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 16:16:04.721 SET FEATURES [Set transfer mode]
Error 158 occurred at disk power-on lifetime: 8546 hours (356 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 78 d2 8f 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 00 d2 8f 09 08 16:16:01.662 READ FPDMA QUEUED
ef 10 02 00 00 00 00 08 16:16:01.662 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 16:16:01.662 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 16:16:01.661 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 16:16:01.661 SET FEATURES [Set transfer mode]
Error 157 occurred at disk power-on lifetime: 8546 hours (356 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 78 d2 8f 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 00 d2 8f 09 08 16:15:58.458 READ FPDMA QUEUED
ef 10 02 00 00 00 00 08 16:15:58.458 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 16:15:58.458 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 16:15:58.457 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 16:15:58.457 SET FEATURES [Set transfer mode]
Error 156 occurred at disk power-on lifetime: 8546 hours (356 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 78 d2 8f 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 00 d2 8f 09 08 16:15:55.254 READ FPDMA QUEUED
ef 10 02 00 00 00 00 08 16:15:55.253 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 08 16:15:55.253 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 08 16:15:55.253 IDENTIFY DEVICE
ef 03 46 00 00 00 00 08 16:15:55.252 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 8551 -
# 2 Extended offline Completed: read failure 60% 8550 160408163
# 3 Short offline Completed without error 00% 8547 -
# 4 Conveyance offline Completed: read failure 90% 8532 160420472
# 5 Short offline Completed: read failure 90% 8532 160420472
# 6 Short offline Completed without error 00% 1 -
# 7 Short offline Interrupted (host reset) 80% 1 -
# 8 Short offline Completed without error 00% 0 -
# 9 Offline Interrupted (host reset) 90% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Тема: перестала загружаться ubuntu 10.04 после обновлений 19.10.10 (Прочитано 7523 раз)
