Месяц прошёл. Надо ноут крайняк восстанавливать!
Вынул проблемный винт - лив-сиди начал нормально работать - все глюки пропали. фууууф.
Выполнил предложенную команду:
ubuntu@ubuntu:~$ sudo smartctl -a /dev/sda
smartctl 5.40 2010-03-16 r3077 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA family
Device Model: WDC WD1600BEVS-07RST0
Serial Number: WD-WXE507103133
Firmware Version: 04.01G04
User Capacity: 160,041,885,696 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Feb 20 08:20:01 2011 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (7200) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 2
3 Spin_Up_Time 0x0003 187 186 021 Pre-fail Always - 1608
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1025
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 253 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 16905
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 631
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 235
193 Load_Cycle_Count 0x0032 164 164 000 Old_age Always - 110055
194 Temperature_Celsius 0x0022 108 074 000 Old_age Always - 39
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Спецы, подскажите, что делать дальше!
Пользователь решил продолжить мысль 20 Февраля 2011, 06:56:48:
Проверил утилитой WD Data Lifeguard Diagnostic. Все тесты прошёл нормально.
Еще открыл раздел утилитой Ext2Explore - видит файловую систему - всё барохло на месте ))
Пользователь решил продолжить мысль 20 Февраля 2011, 07:23:02:
Запустил утилиту Victoria - пишет SMART status = BAD из-за UDMA_CRC_Error_Count = 1. Ещё бы знать чего эт значит...
Пользователь решил продолжить мысль 20 Февраля 2011, 07:25:11:
на Виктории же прогнал какие-то тесты - говорит no warnings, no errors.