Проблема с hostapd и TP-LINK TL-WN422G(Atheros)

[Bloodmage]

не получается завести этот свисток в качестве точки доступа... старые мануалы как-то не помогают... iw list говорит

Код: [Выделить]


.....
Supported interface modes:
* IBSS
* managed
* monitor
......
т.е. с драйверами из коробки он не может работать в AP mode... много где говорится что нужно поставить madwifi, скомпилил, поставил, но вроде тоже ничего не меняется.... Помогите плз, я уже 3 часа безуспешно пытаюсь что-то сделать, думаю вот нести обратно свисток в магазин(покупал только для того чтоб служил как точка доступа) или пытаться его завести...
D-link DWA-110 заводился без проблем, там чипсет другой, ralink вроде называется

[xeon_greg]

скачай последний compat-wireless и hostapd собирай с поддержкой твоего чипсета, должно завестись

[Bloodmage]

что-то hostapd не собирается...

(Нажмите, чтобы показать/скрыть)

ilya@ilya-laptop:~/hostapd-0.7.3/hostapd$ make
../src/drivers/driver_nl80211.c: In function ‘send_and_recv’:
../src/drivers/driver_nl80211.c:202: warning: passing argument 1 of ‘nl_send_auto_complete’ from incompatible pointer type
/usr/include/netlink/netlink.h:53: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c:217: warning: passing argument 1 of ‘nl_recvmsgs’ from incompatible pointer type
/usr/include/netlink/netlink.h:63: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c: In function ‘nl_get_multicast_id’:
../src/drivers/driver_nl80211.c:282: warning: passing argument 1 of ‘genl_ctrl_resolve’ from incompatible pointer type
/usr/include/netlink/genl/ctrl.h:30: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c: In function ‘wpa_driver_nl80211_event_receive’:
../src/drivers/driver_nl80211.c:1095: warning: passing argument 1 of ‘nl_recvmsgs’ from incompatible pointer type
/usr/include/netlink/netlink.h:63: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c: In function ‘wpa_driver_nl80211_init_nl’:
../src/drivers/driver_nl80211.c:1265: warning: implicit declaration of function ‘nl_handle_alloc_cb’
../src/drivers/driver_nl80211.c:1265: warning: assignment makes pointer from integer without a cast
../src/drivers/driver_nl80211.c:1272: warning: assignment makes pointer from integer without a cast
../src/drivers/driver_nl80211.c:1279: warning: passing argument 1 of ‘genl_connect’ from incompatible pointer type
/usr/include/netlink/genl/genl.h:23: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c:1285: warning: passing argument 1 of ‘genl_connect’ from incompatible pointer type
/usr/include/netlink/genl/genl.h:23: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c:1304: warning: passing argument 1 of ‘genl_ctrl_alloc_cache’ from incompatible pointer type
/usr/include/netlink/genl/ctrl.h:25: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c:1304: error: too few arguments to function ‘genl_ctrl_alloc_cache’
../src/drivers/driver_nl80211.c:1310: warning: passing argument 1 of ‘genl_ctrl_alloc_cache’ from incompatible pointer type
/usr/include/netlink/genl/ctrl.h:25: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c:1310: error: too few arguments to function ‘genl_ctrl_alloc_cache’
../src/drivers/driver_nl80211.c:1327: warning: passing argument 1 of ‘nl_socket_add_membership’ from incompatible pointer type
/usr/include/netlink/socket.h:30: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c:1337: warning: passing argument 1 of ‘nl_socket_add_membership’ from incompatible pointer type
/usr/include/netlink/socket.h:30: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c:1345: warning: passing argument 1 of ‘nl_socket_get_fd’ from incompatible pointer type
/usr/include/netlink/socket.h:57: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c:1355: warning: implicit declaration of function ‘nl_handle_destroy’
../src/drivers/driver_nl80211.c: In function ‘wpa_driver_nl80211_init’:
../src/drivers/driver_nl80211.c:1425: warning: passing argument 1 of ‘nl_socket_get_fd’ from incompatible pointer type
/usr/include/netlink/socket.h:57: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
../src/drivers/driver_nl80211.c: In function ‘wpa_driver_nl80211_deinit’:
../src/drivers/driver_nl80211.c:1599: warning: passing argument 1 of ‘nl_socket_get_fd’ from incompatible pointer type
/usr/include/netlink/socket.h:57: note: expected ‘struct nl_sock *’ but argument is of type ‘struct nl_handle *’
make: *** [../src/drivers/driver_nl80211.o] Ошибка 1

.config:

(Нажмите, чтобы показать/скрыть)

# Example hostapd build time configuration
#
# This file lists the configuration options that are used when building the
# hostapd binary. All lines starting with # are ignored. Configuration option
# lines must be commented out complete, if they are not to be included, i.e.,
# just setting VARIABLE=n is not disabling that variable.
#
# This file is included in Makefile, so variables like CFLAGS and LIBS can also
# be modified from here. In most cass, these lines should use += in order not
# to override previous values of the variables.

# Driver interface for Host AP driver
CONFIG_DRIVER_HOSTAP=y

# Driver interface for wired authenticator
#CONFIG_DRIVER_WIRED=y

# Driver interface for madwifi driver
CONFIG_DRIVER_MADWIFI=y
CFLAGS += -I../../madwifi # change to the madwifi source directory

# Driver interface for drivers using the nl80211 kernel interface
CONFIG_DRIVER_NL80211=y
# driver_nl80211.c requires a rather new libnl (version 1.1) which may not be
# shipped with your distribution yet. If that is the case, you need to build
# newer libnl version and point the hostapd build to use it.
LIBNL=/usr/src/libnl
CFLAGS += -I$(LIBNL)/include
LIBS += -L$(LIBNL)/lib

# Driver interface for FreeBSD net80211 layer (e.g., Atheros driver)
#CONFIG_DRIVER_BSD=y
#CFLAGS += -I/usr/local/include
#LIBS += -L/usr/local/lib
#LIBS_p += -L/usr/local/lib
#LIBS_c += -L/usr/local/lib

# Driver interface for no driver (e.g., RADIUS server only)
#CONFIG_DRIVER_NONE=y

# IEEE 802.11F/IAPP
CONFIG_IAPP=y

# WPA2/IEEE 802.11i RSN pre-authentication
CONFIG_RSN_PREAUTH=y

# PeerKey handshake for Station to Station Link (IEEE 802.11e DLS)
CONFIG_PEERKEY=y

# IEEE 802.11w (management frame protection)
# This version is an experimental implementation based on IEEE 802.11w/D1.0
# draft and is subject to change since the standard has not yet been finalized.
# Driver support is also needed for IEEE 802.11w.
#CONFIG_IEEE80211W=y

# Integrated EAP server
CONFIG_EAP=y

# EAP-MD5 for the integrated EAP server
CONFIG_EAP_MD5=y

# EAP-TLS for the integrated EAP server
CONFIG_EAP_TLS=y

# EAP-MSCHAPv2 for the integrated EAP server
CONFIG_EAP_MSCHAPV2=y

# EAP-PEAP for the integrated EAP server
CONFIG_EAP_PEAP=y

# EAP-GTC for the integrated EAP server
CONFIG_EAP_GTC=y

# EAP-TTLS for the integrated EAP server
CONFIG_EAP_TTLS=y

# EAP-SIM for the integrated EAP server
#CONFIG_EAP_SIM=y

# EAP-AKA for the integrated EAP server
#CONFIG_EAP_AKA=y

# EAP-AKA' for the integrated EAP server
# This requires CONFIG_EAP_AKA to be enabled, too.
#CONFIG_EAP_AKA_PRIME=y

# EAP-PAX for the integrated EAP server
#CONFIG_EAP_PAX=y

# EAP-PSK for the integrated EAP server (this is _not_ needed for WPA-PSK)
#CONFIG_EAP_PSK=y

# EAP-SAKE for the integrated EAP server
#CONFIG_EAP_SAKE=y

# EAP-GPSK for the integrated EAP server
#CONFIG_EAP_GPSK=y
# Include support for optional SHA256 cipher suite in EAP-GPSK
#CONFIG_EAP_GPSK_SHA256=y

# EAP-FAST for the integrated EAP server
# Note: Default OpenSSL package does not include support for all the
# functionality needed for EAP-FAST. If EAP-FAST is enabled with OpenSSL,
# the OpenSSL library must be patched (openssl-0.9.9-session-ticket.patch)
# to add the needed functions.
#CONFIG_EAP_FAST=y

# Wi-Fi Protected Setup (WPS)
#CONFIG_WPS=y
# Enable UPnP support for external WPS Registrars
#CONFIG_WPS_UPNP=y

# EAP-IKEv2
#CONFIG_EAP_IKEV2=y

# Trusted Network Connect (EAP-TNC)
#CONFIG_EAP_TNC=y

# PKCS#12 (PFX) support (used to read private key and certificate file from
# a file that usually has extension .p12 or .pfx)
CONFIG_PKCS12=y

# RADIUS authentication server. This provides access to the integrated EAP
# server from external hosts using RADIUS.
#CONFIG_RADIUS_SERVER=y

# Build IPv6 support for RADIUS operations
CONFIG_IPV6=y

# IEEE Std 802.11r-2008 (Fast BSS Transition)
#CONFIG_IEEE80211R=y

# Use the hostapd's IEEE 802.11 authentication (ACL), but without
# the IEEE 802.11 Management capability (e.g., madwifi or FreeBSD/net80211)
#CONFIG_DRIVER_RADIUS_ACL=y

# IEEE 802.11n (High Throughput) support
#CONFIG_IEEE80211N=y

# Remove debugging code that is printing out debug messages to stdout.
# This can be used to reduce the size of the hostapd considerably if debugging
# code is not needed.
#CONFIG_NO_STDOUT_DEBUG=y

# Remove support for RADIUS accounting
#CONFIG_NO_ACCOUNTING=y

# Remove support for RADIUS
#CONFIG_NO_RADIUS=y

# Remove support for VLANs
#CONFIG_NO_VLAN=y

# Remove support for dumping state into a file on SIGUSR1 signal
# This can be used to reduce binary size at the cost of disabling a debugging
# option.
#CONFIG_NO_DUMP_STATE=y

# Enable tracing code for developer debugging
# This tracks use of memory allocations and other registrations and reports
# incorrect use with a backtrace of call (or allocation) location.
#CONFIG_WPA_TRACE=y
# For BSD, comment out these.
#LIBS += -lexecinfo
#LIBS_p += -lexecinfo
#LIBS_c += -lexecinfo

# Use libbfd to get more details for developer debugging
# This enables use of libbfd to get more detailed symbols for the backtraces
# generated by CONFIG_WPA_TRACE=y.
#CONFIG_WPA_TRACE_BFD=y
# For BSD, comment out these.
#LIBS += -lbfd -liberty -lz
#LIBS_p += -lbfd -liberty -lz
#LIBS_c += -lbfd -liberty -lz

compat-wireless скачал, поставил, iw list по-прежнему выдаёт:

Код: [Выделить]

...............
Supported interface modes:
* IBSS
* managed
* monitor

.........
Нужно же чтоб там AP ещё было или не обязательно?

да, всё это делаю пока на ноуте и после установки compat-wireless отвалился встроенный Wi-Fi адаптер Intel Corporation WiFi Link 5100 (драйвер iwlagn)... как бы его снова задействовать, а то на свистке сидеть неохота всё время и ещё почему-то когда я отключаю свисток от USB-порта система полностью повисает...

[xeon_greg]

собирать по образу и подобию только для своей карты выбирать драйвер http://www.gentoo.ru/node/21342

[Bloodmage]

попробую чуть позже, а ничего что

Код: [Выделить]

...............
Supported interface modes:
* IBSS
* managed
* monitor

.........?
hostapd переведёт его в режим Master?

[xeon_greg]

да

[Bloodmage]

так... hostapd всё же скомпилил, установил, но при запуске:

Код: [Выделить]

ilya@ilya-laptop:~$ sudo hostapd ./ha.conf
Configuration file: ./ha.conf
Failed to update rate sets in kernel module
Could not connect to kernel driver.
Using interface wlan3 with hwaddr d8:5d:4c:9a:04:4e and ssid 'test'
Failed to set beacon head/tail or DTIM period
Failed to set CTS protect in kernel driver
Could not set preamble for kernel driver

и не переходит в master... iwconfig:

Код: [Выделить]

ilya@ilya-laptop:~$ iwconfig

wlan0     IEEE 802.11abg  ESSID:off/any 
          Mode:Ad-Hoc  Frequency:2.412 GHz  Cell: Not-Associated   
          Tx-Power=15 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:on
         

wlan3     IEEE 802.11bgn  ESSID:off/any 
          Mode:Managed  Access Point: Not-Associated   Tx-Power=20 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:off
         
mon.wlan3  IEEE 802.11bgn  Mode:Monitor  Tx-Power=20 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:off


ha.conf:

Код: [Выделить]

interface=wlan3
#driver=madwifi
driver=nl80211
ssid=test
channel=1

тут вопрос... драйвер тут всё-таки какой юзать? nl80211 или всё же madwifi? с madwifi вообще не запускается....
Пользователь решил продолжить мысль 18 Марта 2011, 15:43:20:хм... пересобрал и поставил compat-wireless предварительно выбрав драйвер atheros, теперь запуск hostapd приводит к kernel панике....