Доброго времени суток!
Имеется Samsung NP530U3B-A04RU, НОВЫЙ! После покупки был не рад... Сильно греется, мало работает от батареи, уже успел умереть HDD (заменили по гарантии), не дружит с домашней Wifi точкой. В итоге после возврата из СЦ, решил поставить Ubuntu. Вопрос с Wifi решен, остальное ладно пока =) Так вот изначально при установке ничего не мог сделать со внутренним SSD (16gb). Забил и поставил систему на хард. Система работает стабильно, только вот загрузка занимает туеву хучу времени. И как я думаю, судя по логу, проблема с этим проклятым SSD. Я не так глубоко изучал *unix подобные системы, поэтому прошу сильно не пинать... По прежнему с диском сделать ничего не могу. Его попросту не видно в системе, хотя он есть. Дисковая утилита кстати видит его (SSD), но толку ноль, на все мои потуги отвечает например:
Error creating partition table: helper exited with exit code 1: Error calling fsync(2) on /dev/sdb: Input/output error"Проблемный" кусок лога загрузки:
[ 1.451499] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.452616] ata1.00: ATA-8: Hitachi HTS545050A7E380, GG2OA6C0, max UDMA/133
[ 1.452634] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.453894] ata1.00: configured for UDMA/133
[ 1.454084] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54505 GG2O PQ: 0 ANSI: 5
[ 1.454351] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.454358] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 1.454363] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.454511] sd 0:0:0:0: [sda] Write Protect is off
[ 1.454516] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.454660] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.463483] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[ 1.533531] sda: sda1 sda2 < sda5 >
[ 1.534848] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.596615] hub 1-1:1.0: USB hub found
[ 1.596803] hub 1-1:1.0: 6 ports detected
[ 1.707473] usb 2-1: new high-speed USB device number 2 using ehci_hcd
[ 1.771458] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.772054] ata2.00: ATA-9: SanDisk SSD i100 16GB, 11.00.04, max UDMA/133
[ 1.772060] ata2.00: 31277232 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 1.772325] ata2.00: configured for UDMA/133
[ 1.772632] scsi 1:0:0:0: Direct-Access ATA SanDisk SSD i100 11.0 PQ: 0 ANSI: 5
[ 1.772858] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 1.772888] sd 1:0:0:0: [sdb] 31277232 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 1.773115] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.773121] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.773296] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.775417] sdb: sdb1
[ 1.776082] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1.807441] Refined TSC clocksource calibration: 1396.827 MHz.
[ 1.807449] Switching to clocksource tsc
[ 1.840451] hub 2-1:1.0: USB hub found
[ 1.840645] hub 2-1:1.0: 6 ports detected
[ 1.911654] usb 1-1.2: new full-speed USB device number 3 using ehci_hcd
[ 2.079635] usb 1-1.4: new high-speed USB device number 4 using ehci_hcd
[ 2.091407] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.411366] ata5: SATA link down (SStatus 0 SControl 300)
[ 2.413899] Freeing unused kernel memory: 924k freed
[ 2.414065] Write protecting the kernel read-only data: 12288k
[ 2.421666] Freeing unused kernel memory: 1612k freed
[ 2.427508] Freeing unused kernel memory: 1200k freed
[ 2.450855] udevd[106]: starting version 175
[ 2.517817] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.517851] r8169 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 2.517910] r8169 0000:02:00.0: setting latency timer to 64
[ 2.518021] r8169 0000:02:00.0: irq 46 for MSI/MSI-X
[ 2.518771] r8169 0000:02:00.0: eth0: RTL8168evl/8111evl at 0xffffc9000066c000, e8:03:9a:a5:01:13, XID 0c900800 IRQ 46
[ 2.518778] r8169 0000:02:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 2.525712] input: Microsoft Microsoft\xffffffc2\xffffffae\xffffffae 2.4GHz Transceiver v5.0 as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input4
[ 2.525955] generic-usb 0003:045E:074F.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft\xffffffc2\xffffffae\xffffffae 2.4GHz Transceiver v5.0] on usb-0000:00:1a.0-1.2/input0
[ 2.525992] usbcore: registered new interface driver usbhid
[ 2.525997] usbhid: USB HID core driver
[ 2.575573] usb 2-1.5: new full-speed USB device number 3 using ehci_hcd
[ 3.013661] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 33.023611] ata2.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
[ 33.023618] ata2.00: failed command: READ FPDMA QUEUED
[ 33.023626] ata2.00: cmd 60/08:00:a8:3f:dd/00:00:01:00:00/40 tag 0 ncq 4096 in
[ 33.023627] res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 33.023631] ata2.00: status: { DRDY }
[ 33.023638] ata2: hard resetting link
[ 38.390941] ata2: link is slow to respond, please be patient (ready=0)
[ 43.038394] ata2: COMRESET failed (errno=-16)
[ 43.038401] ata2: hard resetting link
[ 48.405705] ata2: link is slow to respond, please be patient (ready=0)
[ 53.053165] ata2: COMRESET failed (errno=-16)
[ 53.053172] ata2: hard resetting link
[ 58.420472] ata2: link is slow to respond, please be patient (ready=0)
[ 88.096830] ata2: COMRESET failed (errno=-16)
[ 88.096838] ata2: limiting SATA link speed to 3.0 Gbps
[ 88.096841] ata2: hard resetting link
[ 93.128213] ata2: COMRESET failed (errno=-16)
[ 93.128221] ata2: reset failed, giving up
[ 93.128225] ata2.00: disabled
[ 93.128231] ata2.00: device reported invalid CHS sector 0
[ 93.136219] ata2: EH complete
[ 93.136261] sd 1:0:0:0: [sdb] Unhandled error code
[ 93.136266] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 93.136273] sd 1:0:0:0: [sdb] CDB: Read(10): 28 00 01 dd 3f a8 00 00 08 00
[ 93.136289] end_request: I/O error, dev sdb, sector 31276968
[ 93.136296] Buffer I/O error on device sdb, logical block 3909621
[ 97.151164] init: bootchart main process (336) terminated with status 127
[ 97.370492] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 97.373483] udevd[380]: starting version 175
[ 97.634954] Adding 4084732k swap on /dev/sda5. Priority:-1 extents:1 across:4084732k
[ 99.950640] lp: driver loaded but no devices found
[ 100.806043] wmi: Mapper loaded
[ 100.976178] psmouse serio1: elantech: assuming hardware version 3 (with firmware version 0x450f00)
[ 100.991622] psmouse serio1: elantech: Synaptics capabilities query result 0x08, 0x17, 0x0c.
[ 101.045499] cfg80211: Calling CRDA to update world regulatory domain
[ 101.067075] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input5
[ 101.217743] mei: module is from the staging directory, the quality is unknown, you have been warned.
[ 101.218178] mei 0000:00:16.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 101.218187] mei 0000:00:16.0: setting latency timer to 64
[ 101.218271] mei 0000:00:16.0: irq 47 for MSI/MSI-X
[ 101.667420] sd 1:0:0:0: [sdb] Unhandled error code
[ 101.667425] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 101.667431] sd 1:0:0:0: [sdb] CDB: Read(10): 28 00 01 dd 40 00 00 00 08 00
[ 101.667447] end_request: I/O error, dev sdb, sector 31277056
[ 101.667453] Buffer I/O error on device sdb, logical block 3909632
[ 101.667491] sd 1:0:0:0: [sdb] Unhandled error code
[ 101.667494] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 101.667498] sd 1:0:0:0: [sdb] CDB: Read(10): 28 00 01 dd 40 00 00 00 08 00
[ 101.667508] end_request: I/O error, dev sdb, sector 31277056
[ 101.667511] Buffer I/O error on device sdb, logical block 3909632
[ 101.667542] sd 1:0:0:0: [sdb] Unhandled error code
Снова идти в СЦ не хочу, ноут нужен для работы.
Вопрос - как отключить инициализацию (или что это) sdb при загрузке? Просто может пусть он умирает своей тихой смертью и не мешает жить остальному железу? Альтернативное решение?
P.S. iSSD намертво припаян к плате, отключить его не получится думаю никак
Тема: Долгая загрузка np530u3b (Прочитано 2790 раз)
