smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-31-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint M8 (AF)
Device Model: SAMSUNG HN-M500MBB
Serial Number: S2RSJ9CB812118
LU WWN Device Id: 5 0024e9 205d9e437
Firmware Version: 2AR10001
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Feb 28 15:40:58 2017 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 6240) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 104) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 5225
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 091 085 025 Pre-fail Always - 2852
4 Start_Stop_Count 0x0032 095 095 000 Old_age Always - 6023
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 28862
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 099 099 000 Old_age Always - 1845
12 Power_Cycle_Count 0x0032 095 095 000 Old_age Always - 5691
191 G-Sense_Error_Rate 0x0022 098 098 000 Old_age Always - 25778
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 053 033 000 Old_age Always - 47 (Min/Max 9/67)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 4
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 100 100 000 Old_age Always - 11
200 Multi_Zone_Error_Rate 0x002a 001 001 000 Old_age Always - 41339
223 Load_Retry_Count 0x0032 099 099 000 Old_age Always - 1845
225 Load_Cycle_Count 0x0032 043 043 000 Old_age Always - 585498
SMART Error Log Version: 1
ATA Error Count: 69 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 69 occurred at disk power-on lifetime: 27233 hours (1134 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 48 36 ae ee Error: UNC 1 sectors at LBA = 0x0eae3648 = 246298184
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 41 36 ae ee 00 00:00:04.010 READ DMA
35 00 08 c8 21 90 e0 00 00:00:04.009 WRITE DMA EXT
35 00 08 80 21 90 e0 00 00:00:04.009 WRITE DMA EXT
35 00 18 50 21 90 e0 00 00:00:04.009 WRITE DMA EXT
35 00 08 28 21 90 e0 00 00:00:04.009 WRITE DMA EXT
Error 68 occurred at disk power-on lifetime: 27233 hours (1134 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 48 36 ae ee Error: UNC 1 sectors at LBA = 0x0eae3648 = 246298184
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 41 36 ae ee 00 00:00:03.308 READ DMA
25 00 18 d8 0f 56 e0 00 00:00:03.308 READ DMA EXT
25 00 08 c0 f9 95 e0 00 00:00:03.305 READ DMA EXT
25 00 08 e8 fb 95 e0 00 00:00:03.305 READ DMA EXT
25 00 08 08 f8 95 e0 00 00:00:03.305 READ DMA EXT
Error 67 occurred at disk power-on lifetime: 27233 hours (1134 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 48 36 ae ee Error: UNC 1 sectors at LBA = 0x0eae3648 = 246298184
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 41 36 ae ee 00 00:00:02.654 READ DMA
35 00 40 f8 4b bd e0 00 00:00:02.653 WRITE DMA EXT
35 00 08 10 4a bd e0 00 00:00:02.653 WRITE DMA EXT
35 00 30 10 29 bd e0 00 00:00:02.653 WRITE DMA EXT
35 00 18 20 0c bd e0 00 00:00:02.653 WRITE DMA EXT
Error 66 occurred at disk power-on lifetime: 27233 hours (1134 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 48 36 ae ee Error: UNC 1 sectors at LBA = 0x0eae3648 = 246298184
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 41 36 ae ee 00 00:00:02.644 READ DMA
35 00 08 f8 28 bd e0 00 00:00:02.643 WRITE DMA EXT
35 00 08 b0 28 bd e0 00 00:00:02.643 WRITE DMA EXT
35 00 10 18 18 bd e0 00 00:00:02.643 WRITE DMA EXT
ea 00 00 00 00 00 e0 00 00:00:02.643 FLUSH CACHE EXT
Error 65 occurred at disk power-on lifetime: 27233 hours (1134 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 48 36 ae ee Error: UNC 1 sectors at LBA = 0x0eae3648 = 246298184
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 41 36 ae ee 00 00:00:02.271 READ DMA
25 00 08 a8 b4 95 e0 00 00:00:02.271 READ DMA EXT
25 00 08 b0 c1 95 e0 00 00:00:02.271 READ DMA EXT
25 00 08 b8 c7 95 e0 00 00:00:02.271 READ DMA EXT
25 00 08 d8 c5 95 e0 00 00:00:02.271 READ DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.