Форум русскоязычного сообщества Ubuntu


Получить помощь и пообщаться с другими пользователями Ubuntu можно
на irc канале #ubuntu-ru в сети Freenode
и в Jabber конференции ubuntu@conference.jabber.ru

Автор Тема: устанавил дрова на ATI и стало ещё хуже  (Прочитано 2268 раз)

0 Пользователей и 1 Гость просматривают эту тему.

Оффлайн elenberg

  • Автор темы
  • Новичок
  • *
  • Сообщений: 11
    • Просмотр профиля
при запуски каталист контрол сервер выдаёт чтобы я настроил дрова с помощью aticonfig. набрав это в консоле мне выдаётся вот что -



Parses an existing X-Server configuration file and modifies it to operate with
ATI products.

The following command-line options can be invoked as parameters:

ATI Initial Configuration:
  --initial
        Generate a default ATI device section in the configuration file which
        is capable of loading the fglrx driver.
  --initial=dual-head
        Same as '--initial' but generate a basic dual head configuration file.
  --initial=check
        Identifies if the fglrx driver is present in configuration file.

TV Options:
  --tvf, --tv-format-type=STRING
        Change the TV signal format.  STRING can be one of:
           NTSC-M
           NTSC-JPN
           NTSC-N
           PAL-B
           PAL-COMB-N
           PAL-D
           PAL-G
           PAL-H
           PAL-I
           PAL-K
           PAL-K1
           PAL-L
           PAL-M
           PAL-N
           PAL-SECAM-D
           PAL-SECAM-K
           PAL-SECAM-K1
           PAL-SECAM-L
        Note: Not all graphics cards support every mode. Regional
              settings are applicable.
  --tvs, --tv-standard-type=STRING
        Change the TV standard for TV output.  STRING can be one of:
            VIDEO
            SCART
            YUV
 --tv-overscan={on|off}
       Enable or disable overscan mode for TVout
       Note, not all tv-formats support overscan. Try to
       toggle overscan off before changing tv-format if
       and error occurs.
 --tv-info
         Print out the current tv geometry, tv format, and if the
         tv is physically connected.
 --tv-geometry=WIDTHxHEIGHT{+|-}X{+|-}Y
              =WIDTHxHEIGHT
         Change the size and position of the TVout display.
         WIDTH and HEIGHT are in percentage units. Please note
         that the valid range for WIDTH and HEIGHT depends on
         the tv-format selected. However, as a rule of thumb
         WIDTH and HEIGHT are valid in the range [1,100]
         X and Y are pixels offsets from centre
         of the screen. X and Y are have variable ranges dependant
         on ASIC. Use tv-info to get valid X and Y ranges
         If tv-geometry is invoked with just width and height
         then X and Y are assumed to be 0
         See example 5 below for a sample usage.

FireGL Workstation Board Features:
  --app, --use-app-profile=STRING
        Change the application profile for a FireGL workstation board.
        STRING can be one of:
            default
            maya
            softimage-xsi
            softimage-3d
            houdini4.0
            houdini5.0
            houdini5.5
Screen-Related Options:
  --ovt, --overlay-type=STRING
        Change the overlay for the X server.  STRING can be one of:
            opengl
            Xv
            disable
  --ovon, --overlay-on={0|1}
        Choose which head the hardware overlay should be visible on.  The
        hardware overlay can be used for either OpenGL, video, pseudo-color
        or stereo.
  --lcd, --lcd-mode=STRING
        Change the LCD mode.  STRING can be one of:
            center
            full
  --dtop, --desktop-setup=STRING
        Change the desktop setup for multiple display adapters.
        STRING can be one of:
            single              1 screen, second dark
            mirror              2 screens - same content, identical
                                refresh rate/resolution
                                Note: This option is NOT supported with Avivo
            clone               2 screens - same content, allows for
                                different refresh rates/resolutions
            horizontal          2 screens - one framebuffer,
                                screen 1 right of screen 0
            horizontal,reverse  2 screens - one framebuffer,
                                screen 1 left of screen 0
            vertical            2 screens - one framebuffer,
                                screen 1 above of screen 0
            vertical,reverse    2 screens - one framebuffer,
                                screen 1 below of screen 0
        Note:  This option is not valid if '--initial=dual-head' is specified.
  --vs, --sync-vsync={on|off}
        Enable/disable sync buffer swaps with vsync.  Enable this option to
        prevent tearing during 3D rendering.
  --psc, --pseudo-color={on|off}
        Enable/disable pseudo-color visuals.  Enable this option to get 16-bit
        color support.
  --stereo={on|off}
        Enable/disable quad-buffer stereo support.  Enable this option only for
        using applications that support the use of hardware 3D shutter glasses.
  --ss, --stereo-sync={on|off}
        Enable/disable quad-buffer stereo sync.  Enable this option to get 3D
        glasses to synchronize with the infrared transmitter.
  --resolution=Screen#,W1xH1,W2xH2,W3xH3,...
        Set the modes for the specified screen.  You may specify several
        resolutions separated by commas.
        Screens start at 0.  You can use 1 for dual-head
  --hsync=Screen#,LOW-HIGH
        Change the horizontal sync range of the specified monitor.  Make sure
        you know the capabilities of your monitor before changing this option.
        Screens start at 0.  You can use 1 for dual-head
  --vrefresh=Screen#,LOW-HIGH
        Change the vertical refresh range of the specified monitor.  Make sure
        you know the capabilities of your monitor before changing this option.
        Screens start at 0.  You can use 1 for dual-head
  --hsync2=LOW-HIGH
        Change the horizontal sync range of the second display.  Make sure you
        know the capabilities of your monitor before changing this option.
  --vrefresh2=LOW-HIGH
        Change the vertical refresh range of the second display.  Make sure you
        know the capabilities of your monitor before changing this option.
  --mode2=W1xH1,W2XH2,W3xH3,...
        Change the modes for the second display.  You may specify several
        resolutions separated by commas.  Only valid for clone and big desktop
        settings.
  --screen-layout={left|right|above|below}
        Set the secondary screen position for dual head.
  --screen-overlap=NUM
        Set the screen overlap region in big desktop mode to be NUM pixels.
  --force-monitor=STRING[,STRING...]
        Describe all displays that are to be enabled and/or disabled regardless
        of physical connection.  STRING can be one or more of the following
        set, separated by commas:
            crt1
            crt2
            lvds
            tv
            tmds1
            tmds2
            tmds2i
            nocrt1
            nocrt2
            nolvds
            notv
            notmds1
            notmds2
            notmds2i

POWERplay Options:
  Following options will not change the config file.
  These options will be effective immediately. Other options on
  the same command line will be ignored.
  --lsp, --list-powerstates
        Print information about power states and exit.
  --set-powerstate=NUMBER
        Set a power state listed by --list-powerstates.

Advanced Options:
  --sync-video={on|off}
        Enable/disable sync to vsync for AVIVO video.
        This option is enabled by default and is used to prevent
        video tearing. By disabling this option video is free to
        render as fast as the 3D engine can handle. In the case of
        choppy video try to disable sync-video.
  --tls={on|off}
        Enable/disable fast thread local storage.  Disable this option when
        virtual machines or WineX fail to work properly.
  --sb, --signal-block={on|off}
        Enable/disable signal blocking.  Disable this option when debugging a
        multi-threaded OpenGL application.
  --locked-userpages={on|off}
        Enable/disable locked user pages. Disable this option if the system
        hangs when running fgl_glxgears.
        User page lock is no longer available on AGP system now.
  --gcpu, --generic-cpu={on|off}
        Enable/disable generic CPU.  Use this option if the CPU is being
        reported improperly.  For example: If you have an AMD cpu that is
        being reported as Intel.
  --max-gart-size=NUMBER
        Set user-defined max GART size for non-AGP systems.
        Possible integer values are from 64 to 512 (mb).

Dynamic Display Management Options:
  Following options will not change the config file. They are
  used for querying driver, controller and adaptor information.
  These options will be effective immediately. Other options on
  the same command line will be ignored.
  --enable-monitor=STRING,STRING
        Setting current monitor to be enabled. Only 2 displays
        can be enabled at the same time. Any displays
        that are not on the list will be disabled.
        STRING can be one of the following set, separated
        by commas:
            none
            crt1
            crt2
            lvds
            tv
            tmds1
            tmds2
            auto   -- use default policy to enable the displays.
  --query-monitor
        This will return connected and enabled monitor information
  --swap-monitor
        This only works for big desktop setup. This will swap the
        contents on the two monitors.
  --swap-screens={on|off}
        Enable/disable swap heads in dual-head mode.
        This option works only in dual-head mode.

Pair mode options:
  Following options are used for query add and remove pair modes.
  These options will be effective immediately. Other options on
  the same command line will be ignored.
  --list-pairmode
        list all the current existing pair modes the driver can use.
  --add-pairmode=width0xheight0+width1xheight1
        Add one pair mode to the list. width0 and height0 are the
        size of primary display and width1 and height1 for the
        secondary  display.
  --remove-pairmode=index
        Remove one pair mode from the list. User can get index by
        list-pairmode.

External Events Daemon Options:
  Following options will not change the config file. They are
  used to send commands to the atieventsd external events daemon.
  --set-policy=STRING
        Sets the event policy for the daemon to be STRING.
        See the atieventsd(8) manpage for further details.

Display attribute options:
  Following options are used for query and set adjustment of
  specific attribute for specific display. These options will be
  effective immediately. Other options on the same command line
  will be ignored.
  The DISPLAYTYPE in options can be one of the following strings:
        crt1, lvds, tv, tmds1, crt2, tmds2, cv, tmds2i .
   The ATTRIBTYPE in options can be one of the following strings:
        brightness, contrast, saturation, hue, positionX,
        positionY, sizeX, sizeY, overscan, videoStandard
  --query-dispattrib=DISPLAYTYPE,ATTRIBTYPE
        query the specific adjustment info of the specific display.
        if ATTRIBTYPE is not specified, all supported attribute
        information will be printed out.
  --set-dispattrib=DISPLAYTYPE,ATTRIBTYPE:VALUE
        set the attribute value of the specific display.

Connector type options:
  Following options are used for query connector type
  for specific display. These options will be
  effective immediately. Other options on the same command line
  will be ignored.
  The DISPLAYTYPE in options can be one of the following strings:
        crt1, lvds, tv, tmds1, crt2, tmds2, cv, tmds2i .
   --query-connectortype=DISPLAYTYPE
        query the connector type of the specific display.

Component video dongle options:
  Following options are used for query and set dongles for a
  component video. These options will be effective immediately.
  Other options on the same command line will be ignored.
  --query-cvdongle
        query dongle setting informations of the component video.
  --set-cvdongle=VALUE
        set the custom override value of the CV dongle.
  --reset-cvdongle
        reset the custom override setting(to zero)of the CV dongle.

Component video customized mode options:
  Following options are used for query and set customized mode for
  component video. These options will be effective immediately.
  Other options on the same command line will be ignored.
  --query-cvmode
        query customized modes for component video.
  --add-cvmode=WIDTH,HEIGHT,FLAGS,BASEWIDTH,BASEDHEIGHT,REFRESH.
        add a customized mode for component video.
  --validate-cvmode=WIDTH,HEIGHT,FLAGS,BASEWIDTH,BASEHEIGHT,REFRESH.
        validate a customized mode for component video.
  --delete-cvmode=INDEX
        delete one customized mode for component video.

Persistent Configuration Store (PCS) Options:
  Following options will not change the config file. They are
  used to manipulate the PCS database.  Due to their nature, these.
  commands may only be run by the root user. Note that the prefix
  and key names are not case-sensitive.
  --get-pcs-key=PREFIX,KEY
        Prints out the specified prefix and key from the PCS
        database.  The type of data will be shown along with
        the contents.
  --set-pcs-val=PREFIX,KEY,VALUE
        Sets an integer value at the specified prefix and key in
        the PCS database.  The value may be specified in hex by
        prefixing it with 0x or in octal by prefixing it with 0,
        otherwise the value is assumed to be in decimal.
  --set-pcs-str=PREFIX,KEY,STRING
        Sets a string value at the specified prefix and key in
        the PCS database.
  --set-pcs-raw=PREFIX,KEY,HEXSTRING
        Sets a raw binary value at the specified prefix and key in
        the PCS database.  The value is specified as a series of
        hex bytes with no 0x or spaces.
        (e.g. --set-pcs-raw="TestSection,TestData,E84C0E" sets 3 bytes)
  --del-pcs-key=PREFIX,KEY
        Deletes the specified prefix and key from the PCS database.

X Server Options:
  --xinerama={on|off}
        Enable or disable Xinerama within the X Server configuration.

Miscellaneous Options:
  -v, --verbose
        Show what aticonfig is doing.
  -q, --quiet
        Disable all information output except for errors.
  --effective={now,startup}
        Choose when the requested changes should take effect.
            now:     Immediately.  This change will affect the running X
                     session if applicable.  Only 'set-powerstate' and
                     'overlay-on' are applicable for now.
            startup: On future X server startups.  This change will modify the
                     X server configuration file if applicable.
        The default is 'now,startup', i.e., do both as applicable.
  --nobackup
        Do not make an automatic backup of the configuration file.
  -i, --input=FILE
        Select a FILE to input as the configuration file. Set FILE to '-' to
        pipe from standard input.  Without this option, aticonfig will search
        /etc/X11 for the default configuration file.
  -o, --output=FILE
        Select a FILE to output the new configuration file to.  Set FILE to '-'
        to print to standard output.  Without this option, aticonfig will
        replace the input file with the newly generated file.
  -h, --help
        Display this help screen.
  -f, --force
        Only valid with 'initial' option.  Force aticonfig to generate default
        Monitor, Device, and Screen sections even if the original configuration
        file has invalid settings in these sections.

Examples:
  1. Setting up fglrx for the first time.
       Single head :    aticonfig --initial --input=/etc/X11/xorg.conf
       Dual head   :    aticonfig --initial=dual-head --screen-layout=above
                        This command will generate a dual head configuration
                        file with the second screen located above the first
                        screen.
  2. Setting up big desktop to horizontal and set overlay on secondary display.
                        aticonfig --dtop=horizontal --overlay-on=1
  3. Setting up modes for primary display.
                        aticonfig --resolution=0,1600x1200,1280x1024,1024x768
  4. Force primary CRT on and TV-out off.
                        aticonfig --force-monitor=crt1,notv
  5. Change tv geometry
                         aticonfig --tv-geometry=85x90+10-10
         This will set tv to 85% width (where 100% ==
         overscan) 90% height and shift 10 pixels right of centre
         and 10 pixels down of centre.

что тут нада делать ?

Оффлайн elenberg

  • Автор темы
  • Новичок
  • *
  • Сообщений: 11
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #1 : 02 Июня 2008, 19:35:44 »
скажите хатябы как удалить дрова ?  :-\

Оффлайн mechanical

  • Активист
  • *
  • Сообщений: 682
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #2 : 02 Июня 2008, 21:03:16 »
а как вы их ставили?
Archlinux i686 , Lenovo ThinkPad SL510

Оффлайн jel

  • Активист
  • *
  • Сообщений: 828
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #3 : 02 Июня 2008, 21:16:05 »
смотреть Example №1  ;)

aticonfig --initial --input=/etc/X11/xorg.conf

Оффлайн Fliker-09

  • Активист
  • *
  • Сообщений: 338
  • Linux rocks and KDE too!
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #4 : 02 Июня 2008, 22:47:31 »
Что за картишка хотя бы? Чем стало хуже?

Оффлайн elenberg

  • Автор темы
  • Новичок
  • *
  • Сообщений: 11
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #5 : 03 Июня 2008, 07:55:55 »
хуже стало тем што когда включаю эфекты то начинается слайд шоу. хотя до установки дров было ещё боле мение (чучуть претормажиало)

Оффлайн elenberg

  • Автор темы
  • Новичок
  • *
  • Сообщений: 11
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #6 : 03 Июня 2008, 10:34:57 »
а как вы их ставили?
я сам в этом не разбираюсь первый раз ставил мне сказали в терминале зайти под root перетащит туда  вайл с дровами и запустить а дальше я там выбрал овтаматическая установка

Оффлайн mechanical

  • Активист
  • *
  • Сообщений: 682
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #7 : 03 Июня 2008, 12:26:51 »
тогда поищи бэкап для /etc/X11/xorg.conf и замени им текщий файл
Archlinux i686 , Lenovo ThinkPad SL510

Оффлайн Fliker-09

  • Активист
  • *
  • Сообщений: 338
  • Linux rocks and KDE too!
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #8 : 03 Июня 2008, 14:28:47 »
хуже стало тем што когда включаю эфекты то начинается слайд шоу. хотя до установки дров было ещё боле мение (чучуть претормажиало)
- чуть-чуть? Значит наверняка VESA. Дайте-ка сюда свой xorg.conf...

З.Ы. И что за картишка всё-таки?

Оффлайн elenberg

  • Автор темы
  • Новичок
  • *
  • Сообщений: 11
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #9 : 03 Июня 2008, 16:08:37 »
дапрбовался я, запарол полностью линукс пришлось переустанавить  :-[
скажите как правильно устанавить дрова на редеон 9550  сами дрова ati-driver-installer-8-5-x86.x86_64.run

Оффлайн Beliar

  • Новичок
  • *
  • Сообщений: 28
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #10 : 03 Июня 2008, 18:17:49 »
Под чем работаешь? Ubuntu, Kubuntu...? и какая версия? Если Ubuntu 8.04...просто скачай Envy и запусти. Он все сделает за тебя.
Мануал по установке http://www.albertomilone.com/envyngfaq.html#A

Оффлайн elenberg

  • Автор темы
  • Новичок
  • *
  • Сообщений: 11
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #11 : 03 Июня 2008, 19:34:48 »
дау меня ubunyu 8.04

Оффлайн mozg6

  • Новичок
  • *
  • Сообщений: 40
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #12 : 03 Июня 2008, 19:40:19 »
После EnvyNG у меня белый экран и так пока не вернусь на пропиетарные

Оффлайн ADL

  • Активист
  • *
  • Сообщений: 447
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #13 : 03 Июня 2008, 20:42:01 »
странно... в настройках оборудования или графики, точно уже не помню... Ubuntu предложила заюзать проприетарные дрова, на что я согласился, поставил галочку, нажал оке - всё скачалось, установилось, ну после как обычно ctrl+alt+back ибо привык =)

Оффлайн wertwerter

  • Любитель
  • *
  • Сообщений: 86
    • Просмотр профиля
Re: устанавил дрова на ATI и стало ещё хуже
« Ответ #14 : 03 Июня 2008, 21:30:40 »
Что-то сколько я не ставил проприаритар на свою 9550, получал только в конце концов нарядные узоры. Тут https://help.ubuntu.com/community/RadeonDriver сделал как положено, получил Compiz(FPS 1650), и Warcraft без компиза(FPS 2450) и без торможения. Правда, если Warcraft и Compiz, то Варик притормаживает и чуть глючит, но играть можно да и кубик кружится

 

Страница сгенерирована за 0.057 секунд. Запросов: 23.