smartctl 6.2 2013-07-26 r3841 [i686-linux-4.4.0-31-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke,
www.smartmontools.org=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD1200BEVT-00A23T0
Serial Number: WD-WXC1A3010005
LU WWN Device Id: 5 0014ee 2599eeda8
Firmware Version: 01.01A01
User Capacity: 120,034,123,776 bytes [120 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Mon Mar 19 18:35:43 2018 +07
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 3000) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 39) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 1567
3 Spin_Up_Time 0x0027 153 151 021 Pre-fail Always - 1333
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 437
5 Reallocated_Sector_Ct 0x0033 133 133 140 Pre-fail Always FAILING_NOW 534
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 086 086 000 Old_age Always - 10599
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 435
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 420
193 Load_Cycle_Count 0x0032 169 169 000 Old_age Always - 94812
194 Temperature_Celsius 0x0022 106 096 000 Old_age Always - 37
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 534
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 1069 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1069 occurred at disk power-on lifetime: 10599 hours (441 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 93 13 3b ea Error: UNC 8 sectors at LBA = 0x0a3b1393 = 171643795
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 90 13 3b ea 0a 1d+21:22:08.061 READ DMA
ca 00 08 e8 3a e4 e6 0a 1d+21:22:07.474 WRITE DMA
ca 00 48 a0 3a e4 e6 0a 1d+21:22:07.453 WRITE DMA
ca 00 08 78 03 23 e8 0a 1d+21:22:07.438 WRITE DMA
c8 00 08 b0 89 fd e9 0a 1d+21:22:07.348 READ DMA
Error 1068 occurred at disk power-on lifetime: 10599 hours (441 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 93 13 3b ea Error: UNC 8 sectors at LBA = 0x0a3b1393 = 171643795
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 90 13 3b ea 0a 1d+21:22:04.232 READ DMA
ca 00 10 88 3a e4 e6 0a 1d+21:22:04.211 WRITE DMA
c8 00 08 88 13 3b ea 0a 1d+21:22:04.211 READ DMA
ca 00 08 38 be a2 e8 0a 1d+21:22:04.199 WRITE DMA
c8 00 08 80 13 3b ea 0a 1d+21:22:04.199 READ DMA
Error 1067 occurred at disk power-on lifetime: 10599 hours (441 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e2 13 3b ea Error: UNC at LBA = 0x0a3b13e2 = 171643874
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 e0 13 3b ea 0a 1d+21:22:00.957 READ DMA
ec 00 00 00 00 00 a0 0a 1d+21:22:00.949 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 1d+21:22:00.949 SET FEATURES [Set transfer mode]
Error 1066 occurred at disk power-on lifetime: 10599 hours (441 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 93 13 3b ea Error: UNC at LBA = 0x0a3b1393 = 171643795
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 e0 12 3b ea 0a 1d+21:21:58.384 READ DMA
c8 00 00 e0 11 3b ea 0a 1d+21:21:58.359 READ DMA
c8 00 00 e0 10 3b ea 0a 1d+21:21:58.324 READ DMA
c8 00 e0 00 10 3b ea 0a 1d+21:21:58.299 READ DMA
c8 00 20 e0 4b 39 ea 0a 1d+21:21:58.298 READ DMA
Error 1065 occurred at disk power-on lifetime: 10598 hours (441 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 d5 c5 3a ea Error: AMNF 8 sectors at LBA = 0x0a3ac5d5 = 171623893
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d0 c5 3a ea 0a 1d+21:12:06.669 READ DMA
ca 00 08 58 8a e3 e6 0a 1d+21:12:06.647 WRITE DMA
ca 00 18 48 2d 45 e2 0a 1d+21:12:06.619 WRITE DMA
ec 00 00 00 00 00 a0 0a 1d+21:12:06.609 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Тема: Перестала грузиться ОС (Прочитано 2646 раз)
