Перестает работать wi-fi после ждущего режима

[Bugayok]

Тот самый Broadcom

Код: [Выделить]

lspci -knn | grep Net -A2
08:00.0 Network controller [0280]: Broadcom Inc. and subsidiaries BCM43142 802.11b/g/n [14e4:4365] (rev 01)
        Subsystem: Hewlett-Packard Company BCM43142 802.11b/g/n [103c:2230]
        Kernel driver in use: wl

Ставил драйвер по инструкции,

Код: [Выделить]

sudo apt-get install  bcmwl-kernel-source
работает. Однако после перевода в ждущий режим и обратно - wi-fi перестает работать, сети не отображает
перезагрузка network не помогла

[zg_nico]

перезагрузка network не помогла

Попробуйте увести машину в ждущий режим, вернуть обратно, а затем выполнить:

Код: [Выделить]

sudo rmmod -f wl; sudo modprobe wlИ подскажите: заработает ли wifi?

[Bugayok]

Попробовал.
Нет, не помогло, к сожалению

[zg_nico]

Попробовал

А вывод эта команда какой-нибудь дает? Какие-нибудь ошибки возникают?
И после "пробуждения" (выход из спящего режима) машины что команды

Код: [Выделить]

dmesg | egrep -i "(error|fail|warning)"
dmesg | tail -n 20 показывают?

[Bugayok]

Эта команда

Код: [Выделить]

sudo rmmod -f wl; sudo modprobe wlничего не пишет, ошибок не выдает

Далее

Код: [Выделить]

dmesg | egrep -i "(error|fail|warning)"
[    0.459681] pci 0000:0a:00.0: BAR 6: failed to assign [mem size 0x00080000 pref]
[    1.590900] RAS: Correctable Errors collector initialized.
[    1.821804] ACPI Warning: \_SB.PCI0.RP05.PXSX._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20181213/nsarguments-66)
[    3.779277] EXT4-fs (sdb7): re-mounted. Opts: errors=remount-ro
[    4.297359] hp_wmi: query 0xd returned error 0x5
[    4.560400] bluetooth hci0: Direct firmware load for brcm/BCM43142A0-0a5c-216c.hcd failed with error -2
[  466.517467] wl: module verification failed: signature and/or required key missing - tainting kernel
[  473.100331] ata2.00: irq_stat 0x08000000, interface fatal error
[  473.100334] ata2: SError: { UnrecovData CommWake 10B8B BadCRC }
[  473.100338] ata2.00: failed command: READ FPDMA QUEUED
                        res 40/00:38:20:5c:09/00:00:1b:00:00/40 Emask 0x10 (ATA bus error)
[  473.438731] sd 1:0:0:0: [sdb] tag#7 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  473.438752] print_req_error: I/O error, dev sdb, sector 453598240 flags 80700
[  539.627553] ata2.00: irq_stat 0x08000000, interface fatal error
[  539.627555] ata2: SError: { UnrecovData CommWake 10B8B BadCRC }
[  539.627558] ata2.00: failed command: READ FPDMA QUEUED
                        res 40/00:68:10:cd:ef/00:00:17:00:00/40 Emask 0x10 (ATA bus error)
[  539.968235] sd 1:0:0:0: [sdb] tag#13 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  539.968256] print_req_error: I/O error, dev sdb, sector 401591568 flags 80700
[  573.567970] ERROR @wl_cfg80211_scan :
[  573.567972] WLC_SCAN error (-22)


и последняя

Код: [Выделить]

dmesg | tail -n 20
[ 1228.566703] done.
[ 1228.634954] PM: suspend exit
[ 1228.654077] nouveau 0000:0a:00.0: bus: MMIO read of 00000000 FAULT at 6013d4 [ IBUS ]
[ 1228.864908] Generic PHY r8169-900:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=r8169-900:00, irq=IGNORE)
[ 1228.992365] r8169 0000:09:00.0 eno1: Link is Down
[ 1230.373951] usb 1-2: new full-speed USB device number 6 using xhci_hcd
[ 1230.524766] usb 1-2: New USB device found, idVendor=046d, idProduct=c52f, bcdDevice=30.00
[ 1230.524772] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1230.524776] usb 1-2: Product: USB Receiver
[ 1230.524779] usb 1-2: Manufacturer: Logitech
[ 1230.528877] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C52F.0005/input/input27
[ 1230.529367] hid-generic 0003:046D:C52F.0005: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:14.0-2/input0
[ 1230.530923] input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1/0003:046D:C52F.0006/input/input28
[ 1230.590697] hid-generic 0003:046D:C52F.0006: input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2/input1
[ 1231.098261] r8169 0000:09:00.0 eno1: Link is Up - 100Mbps/Full - flow control rx/tx
[ 1231.098272] IPv6: ADDRCONF(NETDEV_CHANGE): eno1: link becomes ready
[ 1272.190915] PKCS#7 signature not signed with a trusted key
[ 1272.225453] wlan0: Broadcom BCM4365 802.11 Hybrid Wireless Controller 6.30.223.271 (r587334)

[ 1272.229552] wl 0000:08:00.0 wlo1: renamed from wlan0