Первый раз себе поставил ubuntu в linux вообще практически ничего не понимаю. Ставил вер.8.04 с live cd. Перечитал вроде уже все руководства по настроике adsl но дошёл только до синхронизации - дальше ошибка. Уже всё перепробовал доустановил всу нужные пакеты build-essencial и pppoe, перепробовал все возможные комбинации настроек и файлов синхронизации, даже создал свой собственный файл синхронизации с помощью сниффера, но всё равно одна и та же ошибка
avrilfan@avrilfan-desktop:~$ sudo eciadsl-probe-device
WARNING: before probing, please ensure that your USB devices are plugged in
and that your system's USB support is properly configured
USB modem to probe must be UNinitialized, it will surely appear as an unknown
device (because it is not initialized yet), for instance: ? (0547:2131)
config read from /etc/eciadsl/eciadsl.conf
your USB devices:
1: EHCI Host Controller / Linux 2.6.24-19-generic ehci_hcd (0000:0000)
2: OHCI Host Controller / Linux 2.6.24-19-generic ohci_hcd (0000:0000)
3: USB-ADSL Modem / Conexant, Inc. (0572:cb16)
enter device to probe (1-3): 3
probing, please wait..
your USB devices now:
1: EHCI Host Controller / Linux 2.6.24-19-generic ehci_hcd (0000:0000)
2: OHCI Host Controller / Linux 2.6.24-19-generic ohci_hcd (0000:0000)
3: USB-ADSL Modem / Conexant, Inc. (0572:cb16)
probed USB device: USB-ADSL Modem / Conexant, Inc.
VID1=0572, PID1=cb16
VID2=0572, PID2=cb16
Did you really unplug/replug your modem before launching this script?
avrilfan@avrilfan-desktop:~$ sudo eciadsl-config-text
===== Welcome to the EciAdsl Linux driver configuration =====
At any time, press Ctrl+C to quit this script without saving modifications.
Tip: you can run eciadsl-config-text with a .bin file as parameter to change
your .bin quickly.
Your choice:
1) Configure all settings
2) Remove dabusb module
3) Change synch .bin file
Enter your choice (1-3, default is 1): 1
===> EciAdsl driver setup <===
Current user name is: avrilfan
Type in your user name (given by your provider, press ENTER to keep the previous one):
* user name unchanged
Type in your password (given by your provider):
Type in your password again (for verification):
Select your provider:
1) AR..Telviso
2) AU..Arachnet
3) AU..iiNet
4) AU..Pacific Internet
5) AU..TPG
6) BE..Belgacom Skynet
7) BE..EDPnet
8) BE..Easynet
9) BE..Openweb
10) BE..PlanetInternet
11) BE..Tiscali Belgium
12) BR..Global Village Telecom
13) CH..Bluewin
14) CH..Econophone
15) CH..Netstream
16) CH..SolNet
17) CH..Sunrise
18) DK..Cybercity
19) DK..Tiscali
20) EG..Noor
21) EG..Menanet
22) ES..Auna
23) ES..Telefonica (ya.com)
24) ES..Wanadoo Spain
25) FI..Elisa Communications
26) FR..9 Telecom
27) FR..Cegetel
28) FR..Club-Internet
29) FR..Easynet
30) FR..Free
31) FR..Nerim
32) FR..Tele2
33) FR..Tiscali
34) FR..Wanadoo (France Telecom)
35) FR..World Online/Tiscali
36) HU..MonorNet
37) IL..Bezeq Intl.
38) IL..Internet Zahav IL
39) IL..Kavei Zahav
40) IL..Netvision
41) IT..Alice Telecom
42) IT..Infostrada
43) IT..Telecom Italia
44) IT..Tiscali Italia
45) PE..Telefonica del Peru
46) PL..Neostrade/TPnet
47) PT..Clix
48) PT..Sapo
49) PT..ViaNetwork
50) RU..Avangard
51) RU..WebPlus
52) SE..Telenordia
53) SG..Pacific Internet
54) SG..Singnet
55) UK..British Telecom
56) UK..Giointernet
57) UK..Kingston/Karoo Rapidtime
58) UK..Pipex UK
59) Other
Enter your choice (1-59, default is 1): 59
If your provider was not listed (or if you want to overwrite
defaults), you can type in your own DNS servers:
DNS1 currently unset
Type in an IP for DNS1 (press ENTER to skip):
DNS2 currently unset
Type in an IP for DNS2 (press ENTER to skip):
Enter now your VPI/VCI (depending on your provider/country)
Example for France: 8 35 (VPI=8, VCI=35)
These values correspond to the number dialed under Windows.
VPI currently set to 0
Type in your VPI (given by your provider, press ENTER to keep the previous one):
* VPI unchanged
VCI currently set to 35
Type in your VCI (given by your provider, press ENTER to keep the previous one):
* VCI unchanged
Select your modem:
1) Previous setting (Other)
2) Aethra Starmodem
3) Allnet ALL768UB
4) Archtek UGW-8000
5) Askey ALE070
6) Askey ALE130
7) Askey ALE150
8) Asus AAM6000UG
9) Atlantis Land I-Storm
10) Aztech 100U
11) BT Voyager
12) BT Voyager 100
13) BT Voyager 105
14) Conceptronic ConADSLUG
15) Conitech Kiowa
16) Cypress Globespan G7000
17) D-Link DSL200
18) D-Link DSL200 rev B
19) D-Link DSL200 rev B1
20) D-Link DSL200 generation III
21) Digicom MichelAngelo
22) Dynalink ALE070
23) ECI B-Focus
24) ECI HiFocus
25) Eicon Diva
26) Ericsson hm120dp
27) Ericsson hm121dp/di
28) Fujitsu FDX310
29) GVC BB039
30) IPM Datacom Webpower
31) IPM Datacom Dataway USB
32) IPM Datacom SpeedWeb USB
33) Kraun ADSL USB (#1)
34) Kraun ADSL USB (#2)
35) Linkmax HSA 100
36) Lucent CellPipe USB-20A (#1)
37) Lucent CellPipe USB-20A (#2)
38) Lucent CellPipe USB-20A (#3)
39) Nortek 2020 (#1)
40) Nortek 2020 (#2)
41) Nortek 2021 (#1)
42) Nortek 2021 (#2)
43) Nortek 2021 (Tiscali)
44) Onixon DSL100U
45) Prolink Hurricane 7000
46) Siemens Santis (#1)
47) Siemens Santis (#2)
48) Siemens Santis (#3)
49) Siemens Santis 10
50) Siemens Santis 100
51) SMC 7003 V.2 USB ADSL
52) Solwise SAR100
53) Solwise EA100
54) Supergrass Surfer
55) Telewell TW-EA100
56) Topcom Webr@cer 850
57) Topcom XPlorer 850
58) Turbocomm EA100
59) Turbocomm EA103
60) US Robotics 8500
61) Virata (Tiscali)
62) Wisecom ws-ad80usg
63) WyTek FM028
64) Xavi X7005Q2
65) Xentrix USB
66) Zoom 5510 ADSL
67) Zyxel Prestige 630-41
68) Other
Enter your choice (1-68, default is 1): 20
If your modem was not listed (or if you want to overwrite defaults),
you can enter your own VID1/PID1/VID2/PID2 (use eciadsl-probe-device
to get them), Globespan chipset and USB alt interface values:
VID1 currently set to 0915
Type in a VID1 (4-digit hexadecimal, press ENTER to keep current value): 0572
PID1 currently set to 8104
Type in a PID1 (4-digit hexadecimal, press ENTER to keep current value): cb16
VID2 currently set to 0915
Type in a VID2 (4-digit hexadecimal, press ENTER to keep current value): 0572
PID2 currently set to 8104
Type in a PID2 (4-digit hexadecimal, press ENTER to keep current value): cb16
Select your modem chipset:
1) Previous setting (GS7470)
2) GS7070
3) GS7470
Enter your choice (1-3, default is 1): 3
USB ALT INTERFACE for SYNCH process currently set to 0
Type in the USB ALT INTERFACE for SYNCH (1-digit decimal (0-5) , press ENTER to keep current value):
* USB ALT INTERFACE for SYNCH unchanged
USB ALT INTERFACE for PPPOECI process currently set to 5
Type in the USB ALT INTERFACE for PPPOECI (1-digit decimal (0-5) , press ENTER to keep current value):
* USB ALT INTERFACE for PPPOECI unchanged
Select your .bin file for synch:
1) Previous setting (/etc/eciadsl/gs7470_synch999.bin)
2) /etc/eciadsl/gs7470_synch06.bin
3) /etc/eciadsl/gs7470_synch21.bin
4) /etc/eciadsl/gs7470_synch999.bin
5) /etc/eciadsl/gs7470_synch04.bin
6) /etc/eciadsl/gs7470_synch20.bin
Enter your choice (1-6, default is 1): 2
Select your PPP mode (use the DEFAULT one if you don't know what this means):
1) Previous setting (LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS)
2) VCM_RFC2364
3) LLC_RFC2364
4) LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS
5) VCM_RFC_1483_BRIDGED_ETH
6) LLC_RFC1483_ROUTED_IP
7) VCM_RFC1483_ROUTED_IP
Enter your choice (1-7, default is 1): 4
In current config, DHCP is disabled
Is DHCP used by your provider (MOST users should say NO)?
(y/n or press ENTER to keep current value)
* DHCP usage unchanged
In current config, static IP is not used
Did you get a static IP from your provider (MOST users should say NO)?
(y/n)
* static IP usage unchanged
==== Configuration will be created with these values :
+ User : avrilfan
+ Password : (hidden)
+ Provider : Other
DNS 1 :
DNS 2 :
+ VPI/VCI : 0/35
+ Modem : D-Link DSL200 generation III
GS chipset : GS7470
VID1/PID1 : 0572/cb16
VID2/PID2 : 0572/cb16
ALT SYNCH : 0
ALT PPPOECI : 5
+ .bin file : /etc/eciadsl/gs7470_synch06.bin
+ PPP mode : LLC_SNAP_RFC1483_BRIDGED_ETH_NO_FCS
+ use DHCP : no
+ use static IP : no
Press ENTER to create config files or Ctrl+C to exit now without saving.
backing up /etc/ppp/chap-secrets to /etc/ppp/chap-secrets.bak32.. OK
modifying /etc/ppp/chap-secrets.. OK
backing up /etc/ppp/pap-secrets to /etc/ppp/pap-secrets.bak32.. OK
modifying /etc/ppp/pap-secrets.. OK
backing up /etc/ppp/peers/adsl to /etc/ppp/peers/adsl.bak31.. OK
modifying /etc/ppp/peers/adsl.. OK
backing up /etc/eciadsl/eciadsl.conf to /etc/eciadsl/eciadsl.conf.bak57.. OK
updating /etc/eciadsl/eciadsl.conf..OK
==== eciadsl-config-text: Configuration updated with success !
You can now run eciadsl-start (as root) to connect to the internet.
avrilfan@avrilfan-desktop:~$ sudo eciadsl-start
[EciAdsl 1/5] Setting up USB support...
Preliminary USB device filesystem is OK
[EciAdsl 2/5] Uploading firmware...
Process skipped .. no more needed
firmware loaded successfully
[EciAdsl 3/5] Synchronization...
pusb_control_msg: Inappropriate ioctl for device
*** glibc detected *** /usr/local/bin/eciadsl-synch: double free or corruption (fasttop): 0x0000000000607240 ***
======= Backtrace: =========
/lib/libc.so.6[0x7fd546faf08a]
/lib/libc.so.6(cfree+0x8c)[0x7fd546fb2c1c]
/usr/local/bin/eciadsl-synch[0x4032f3]
/usr/local/bin/eciadsl-synch[0x402953]
/lib/libc.so.6(__libc_start_main+0xf4)[0x7fd546f591c4]
/usr/local/bin/eciadsl-synch[0x401419]
======= Memory map: ========
00400000-00407000 r-xp 00000000 08:02 573972 /usr/local/bin/eciadsl-synch
00606000-00607000 rw-p 00006000 08:02 573972 /usr/local/bin/eciadsl-synch
00607000-00628000 rw-p 00607000 00:00 0 [heap]
41d94000-41d95000 ---p 41d94000 00:00 0
41d95000-42595000 rw-p 41d95000 00:00 0
42595000-42596000 ---p 42595000 00:00 0
42596000-42d96000 rw-p 42596000 00:00 0
7fd540000000-7fd540021000 rw-p 7fd540000000 00:00 0
7fd540021000-7fd544000000 ---p 7fd540021000 00:00 0
7fd546d2d000-7fd546d3a000 r-xp 00000000 08:02 630847 /lib/libgcc_s.so.1
7fd546d3a000-7fd546f3a000 ---p 0000d000 08:02 630847 /lib/libgcc_s.so.1
7fd546f3a000-7fd546f3b000 rw-p 0000d000 08:02 630847 /lib/libgcc_s.so.1
7fd546f3b000-7fd547093000 r-xp 00000000 08:02 630822 /lib/libc-2.7.so
7fd547093000-7fd547293000 ---p 00158000 08:02 630822 /lib/libc-2.7.so
7fd547293000-7fd547296000 r--p 00158000 08:02 630822 /lib/libc-2.7.so
7fd547296000-7fd547298000 rw-p 0015b000 08:02 630822 /lib/libc-2.7.so
7fd547298000-7fd54729d000 rw-p 7fd547298000 00:00 0
7fd54729d000-7fd5472b3000 r-xp 00000000 08:02 630900 /lib/libpthread-2.7.so
7fd5472b3000-7fd5474b3000 ---p 00016000 08:02 630900 /lib/libpthread-2.7.so
7fd5474b3000-7fd5474b5000 rw-p 00016000 08:02 630900 /lib/libpthread-2.7.so
7fd5474b5000-7fd5474b9000 rw-p 7fd5474b5000 00:00 0
7fd5474b9000-7fd5474d6000 r-xp 00000000 08:02 630802 /lib/ld-2.7.so
7fd5476c6000-7fd5476c8000 rw-p 7fd5476c6000 00:00 0
7fd5476d0000-7fd5476d1000 rw-p 7fd5476d0000 00:00 0
7fd5476d2000-7fd5476d6000 rw-p 7fd5476d2000 00:00 0
7fd5476d6000-7fd5476d8000 rw-p 0001d000 08:02 630802 /lib/ld-2.7.so
7fff4f6c3000-7fff4f6d8000 rw-p 7ffffffea000 00:00 0 [stack]
7fff4f7fe000-7fff4f800000 r-xp 7fff4f7fe000 00:00 0 [vdso]
ffffffffff600000-ffffffffff601000 r-xp 00000000 00:00 0 [vsyscall]
Please Wait.. Synchronisation in progress [-]/usr/local/bin/eciadsl-start: line 517: 23907 Aborted "$BIN_DIR/eciadsl-synch" $synch_options
ERROR: failed to get synchronization
avrilfan@avrilfan-desktop:~$
Тема: Никак не могу настроить d-link dsl 200 gen III (Прочитано 1860 раз)
