Добрый день,
На ноуте lenovo y450-3m столкнулся с проблемой записи лазерных дисков
...
BraseroWodim stdout: Waiting for reader process to fill input buffer ... input buffer ready.
BraseroWodim stdout: Performing OPC...
BraseroWodim stdout: Starting new track at sector: 0
BraseroWodim stdout:
BraseroWodim stderr: Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: CDB: 2A 00 00 00 01 D1 00 00 1F 00
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: status: 0x2 (CHECK CONDITION)
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: Sense Bytes: 70 00 05 00 00 00 00 0A 2A 30 06 90 21 02 00 00
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: Sense Key: 0x5 Illegal Request, Segment 0
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: Sense flags: Blk 0 (not valid)
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: cmd finished after 0.005s timeout 40s
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: wodim: The current problem looks like a buffer underrun.
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: wodim: It looks like 'driveropts=burnfree' does not work for this drive.
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: wodim: Please report.
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: wodim: Make sure that you are root, enable DMA and check your HW/OS set up.
BraseroWodim called brasero_job_get_flags
BraseroWodim stdout: Track 01: 0 of 10 MB written.
BraseroWodim stdout: write track data: error after 952320 bytes
BraseroWodim stdout: Writing time: 17.352s
BraseroWodim stdout: Average write speed 4.3x.
BraseroWodim stdout: Fixating...
BraseroWodim called brasero_job_get_action
BraseroWodim called brasero_job_set_current_action
BraseroWodim stdout: Fixating time: 28.552s
BraseroWodim stderr: wodim: fifo had 79 puts and 16 gets.
BraseroWodim called brasero_job_get_flags
BraseroWodim stdout: HUP
BraseroWodim stderr: wodim: fifo was 0 times empty and 4 times full, min fill was 92%.
BraseroWodim called brasero_job_get_flags
BraseroWodim stderr: HUP
BraseroWodim process finished with status 254
BraseroWodim called brasero_job_error
BraseroWodim finished with an error
BraseroWodim asked to stop because of an error
error = 0
message = "no message"
BraseroGenisoimage stopping
BraseroGenisoimage got killed
BraseroGenisoimage disconnecting BraseroGenisoimage from BraseroWodim
BraseroWodim stopping
BraseroWodim got killed
BraseroWodim closing connection for BraseroWodim
Session error : unknown (brasero_burn_record brasero-burn.c:2811)
sudo hdparm -i /dev/cdrom
/dev/cdrom:
Model=HL-DT-ST, FwRev=RV08, SerialNo=M2T9A5A5157
Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no
Drive conforms to: Unspecified: ATA/ATAPI-4,5,6,7
* signifies the current active mode
1. Есть ли вероятность, что в 10.04 driveropts=burnfree будет работать с моим приводом?
2. k3b этот же driveropts=burnfree использует, или у него свой драйвер от переполнения буфера?
3. Владельцы этого ноута как пишут диски? Может что-то программно только у меня?
Тема: Переполнение буфера при записи дисков на Y450-3M (Прочитано 1778 раз)
