Проблемы с жёсткими дисками

[Looking]

После установки Кубунты 10.4 64-бита (до этого стояли последовательно обновляемые кубунты начиная с 8.10; "чистая" установка в силу ряда причин показалась более привлекательной) нормально видится только один из 3-х SATA дисков. При установке определился только /sda. С помощью манипуляций получилось по UUID подключить через fstab расположенные на /sdb разделы, причём подключаются они через раз. А вот /sdc определяет только как /dev/mapper/nvidia_*, хотя никакого рэйда никогда не было! Разные Partition Managerы при этом прекрасно видят все три диска, но, опять же, монтировать /sdc не хотят! Железо старое: асусовская мать А8NE, атлон 3000+. Куда копать?

[vasilisc]

перезагрузитесь и сразу сюда киньте под спойлер

Код: [Выделить]

sudo dmesg|grep sdи

Код: [Выделить]

sudo lspci -vv

[Looking]

Ответ на sudo dmesg|grep sd
[    1.620544] sd 3:0:0:0: Attached scsi generic sg1 type 0
[    1.620772] sd 3:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[    1.620819] sd 3:0:0:0: [sda] Write Protect is off
[    1.620822] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.620846] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.620982]  sda: sda2 < sda5 sda6 sda7 sda8 sda9 >
[    1.671826] sd 3:0:0:0: [sda] Attached SCSI disk
[    2.030521] sd 4:0:0:0: Attached scsi generic sg2 type 0
[    2.030738] sd 4:0:0:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    2.030781] sd 4:0:0:0: [sdb] Write Protect is off
[    2.030784] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    2.030807] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.030933]  sdb: sdb1 sdb2 sdb3
[    2.051397] sd 4:0:0:0: [sdb] Attached SCSI disk
[    2.530704] sd 5:0:0:0: Attached scsi generic sg3 type 0
[    2.530920] sd 5:0:0:0: [sdc] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    2.530963] sd 5:0:0:0: [sdc] Write Protect is off
[    2.530966] sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    2.530988] sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.531112]  sdc: sdc1 sdc2 sdc3 sdc4
[    2.578946] sd 5:0:0:0: [sdc] Attached SCSI disk
[    3.625801] EXT4-fs (sda8): mounted filesystem with ordered data mode
[   12.630200] Adding 1951856k swap on /dev/sda9.  Priority:-1 extents:1 across:1951856k
[   15.315394] EXT4-fs (sda5): mounted filesystem with ordered data mode
[   15.888813] EXT3 FS on sda6, internal journal
[   15.947342] EXT3 FS on sdc1, internal journal
[   16.265673] EXT3 FS on sda7, internal journal
[   16.312176] EXT3 FS on sdc2, internal journal
[   16.591156] EXT3 FS on sdc3, internal journal
[   16.691372] EXT3 FS on sdc4, internal journal
[   16.882380] type=1505 audit(1272387983.925:9):  operation="profile_load" pid=940 name="/usr/sbin/cupsd"
то бишь диски как я и говорил он, скотина, видит.
А вот какую часть sudo lspci -vv показать, чтобы не загружать ещё пол-страницы?
Пользователь решил продолжить мысль 27 Апреля 2010, 19:55:43:Так, разбиваю на две части sudo lspci -vv, а то оно превышает критичные значения:

(Нажмите, чтобы показать/скрыть)

00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
        Subsystem: ASUSTeK Computer Inc. Device 815a
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [44] HyperTransport: Slave or Primary Interface
                Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
                Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
                Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
                Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
                Revision ID: 1.03
                Link Frequency 0: 1.0GHz
                Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
                Link Frequency 1: 200MHz
                Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
                Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
                Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
                Prefetchable memory behind bridge Upper: 00-00
                Bus Number: 00
        Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed-
                Mapping Address Base: 00000000fee00000

00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
        Subsystem: ASUSTeK Computer Inc. Device 815a
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0

00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
        Subsystem: ASUSTeK Computer Inc. Device 815a
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 255
        Region 0: I/O ports at e400 [size=32]
        Region 4: I/O ports at 4c00 [size=64]
        Region 5: I/O ports at 4c40 [size=64]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: nForce2_smbus
        Kernel modules: i2c-nforce2

00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10)
        Subsystem: ASUSTeK Computer Inc. Device 815a
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 20
        Region 0: Memory at d2004000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ohci_hcd

00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) (prog-if 20)
        Subsystem: ASUSTeK Computer Inc. Device 815a
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin B routed to IRQ 21
        Region 0: Memory at d2005000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [44] Debug port: BAR=1 offset=0098
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ehci_hcd

00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Controller (rev a2)
        Subsystem: ASUSTeK Computer Inc. Device 812a
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (500ns min, 1250ns max)
        Interrupt: pin A routed to IRQ 22
        Region 0: I/O ports at dc00 [size=256]
        Region 1: I/O ports at e000 [size=256]
        Region 2: Memory at d2003000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: Intel ICH
        Kernel modules: snd-intel8x0

00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev a2) (prog-if 8a [Master SecP PriP])
        Subsystem: ASUSTeK Computer Inc. Device 815a
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
        Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled]
        Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
        Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled]
        Region 4: I/O ports at f000 [size=16]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: pata_amd
        Kernel modules: pata_amd

00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev a3) (prog-if 85 [Master SecO PriO])
        Subsystem: ASUSTeK Computer Inc. Device 815a
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 23
        Region 0: I/O ports at 09f0 [size=8]
        Region 1: I/O ports at 0bf0
        Region 2: I/O ports at 0970 [size=8]
        Region 3: I/O ports at 0b70
        Region 4: I/O ports at d800 [size=16]
        Region 5: Memory at d2002000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: sata_nv
        Kernel modules: sata_nv

00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev a3) (prog-if 85 [Master SecO PriO])
        Subsystem: ASUSTeK Computer Inc. Device 815a
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (750ns min, 250ns max)
        Interrupt: pin A routed to IRQ 22
        Region 0: I/O ports at 09e0 [size=8]
        Region 1: I/O ports at 0be0
        Region 2: I/O ports at 0960 [size=8]
        Region 3: I/O ports at 0b60
        Region 4: I/O ports at c400 [size=16]
        Region 5: Memory at d2001000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: sata_nv
        Kernel modules: sata_nv

00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2) (prog-if 01)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Bus: primary=00, secondary=05, subordinate=05, sec-latency=128
        I/O behind bridge: 00008000-00009fff
        Memory behind bridge: d0000000-d1ffffff
        Prefetchable memory behind bridge: 60000000-600fffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr+ DiscTmrStat+ DiscTmrSERREn-

00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
        Subsystem: ASUSTeK Computer Inc. Device 8141
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
        Latency: 0 (250ns min, 5000ns max)
        Interrupt: pin A routed to IRQ 23
        Region 0: Memory at d2000000 (32-bit, non-prefetchable) [size=4K]
        Region 1: I/O ports at b000 [size=8]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
        Kernel driver in use: forcedeth
        Kernel modules: forcedeth

00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
                Address: 00000000fee0100c  Data: 4149
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
                Mapping Address Base: 00000000fee00000
        Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #3, Speed 2.5GT/s, Width x2, ASPM L0s, Latency L0 <512ns, L1 <4us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
                        Slot #  8, PowerLimit 25.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Off, PwrInd On, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [100] Virtual Channel <?>
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
                Address: 00000000fee0100c  Data: 4151
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
                Mapping Address Base: 00000000fee00000
        Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <512ns, L1 <4us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
                        Slot #  4, PowerLimit 10.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Off, PwrInd On, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [100] Virtual Channel <?>
        Kernel driver in use: pcieport
        Kernel modules: shpchp

Пользователь решил продолжить мысль 27 Апреля 2010, 22:05:26:Марлезонский балет, часть вторая:

(Нажмите, чтобы показать/скрыть)

00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
                Address: 00000000fee0100c  Data: 4159
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
                Mapping Address Base: 00000000fee00000
        Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <512ns, L1 <4us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
                        Slot #  2, PowerLimit 10.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Off, PwrInd On, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [100] Virtual Channel <?>
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000a000-0000afff
        Memory behind bridge: b0000000-cfffffff
        Prefetchable memory behind bridge: 0000000060100000-00000000601fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
                Address: 00000000fee0100c  Data: 4161
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
                Mapping Address Base: 00000000fee00000
        Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr+ UncorrErr- FatalErr+ UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s, Latency L0 <512ns, L1 <4us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
                        Slot #  1, PowerLimit 75.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Off, PwrInd On, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [100] Virtual Channel <?>
        Kernel driver in use: pcieport
        Kernel modules: shpchp

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Capabilities: [80] HyperTransport: Host or Secondary Interface
                !!! Possibly incomplete decoding
                Command: WarmRst+ DblEnd-
                Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
                Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
                Revision ID: 1.02

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Kernel driver in use: amd64_edac
        Kernel modules: amd64_edac_mod

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Kernel driver in use: k8temp
        Kernel modules: k8temp

01:00.0 VGA compatible controller: nVidia Corporation G96 [GeForce 9400 GT] (rev a1)
        Subsystem: LeadTek Research Inc. Device 20e3
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at c2000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: Memory at b0000000 (64-bit, prefetchable) [size=256M]
        Region 3: Memory at c0000000 (64-bit, non-prefetchable) [size=32M]
        Region 5: I/O ports at a000 [size=128]
        [virtual] Expansion ROM at 60100000 [disabled] [size=512K]
        Capabilities: [60] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [78] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <4us
                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <1us, L1 <1us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Capabilities: [b4] Vendor Specific Information <?>
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [128] Power Budgeting <?>
        Capabilities: [600] Vendor Specific Information <?>
        Kernel driver in use: nvidia
        Kernel modules: nvidia-current, nvidiafb, nouveau

05:06.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
        Subsystem: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: I/O ports at 8000 [size=8]
        Region 1: I/O ports at 8400
        Region 2: I/O ports at 8800 [size=8]
        Region 3: I/O ports at 8c00
        Region 4: I/O ports at 9000 [size=16]
        Region 5: Memory at d1000000 (32-bit, non-prefetchable) [size=1K]
        [virtual] Expansion ROM at 60000000 [disabled] [size=512K]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-
        Kernel driver in use: sata_sil
        Kernel modules: sata_sil

[kobaltd]

05:06.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
        Subsystem: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: I/O ports at 8000
вот вообщето ваш файк райд - так что ищите у себя в девайсах или уже собранный через dm диск или отключайте  при загрузке через опции ядра обработку файк райдов - точно не помню что то из сери "nodm" или в таком духе

[Looking]

Спасибо, буду пробовать!

Тэк, острота проблемы не снята - в систкме не установлены ни dm-mod ни dmraid, соответственно у меня отсутствует понимание как настроить то, чего нет? Или я ошибаюсь?